DLA SMD-5962-90526 REV N-2008 MICROCIRCUIT DIGITAL CMOS DIGITAL SIGNAL PROCESSOR MONOLITHIC SILICON.pdf

1、REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R060-92 91-11-25 M. L. Poelking B Changes in accordance with NOR 5962-R006-93 92-11-05 M. L. Poelking C Add device type 03. Update boilerplate. Editorial changes throughout. 92-12-10 M. L. Poelking D Add device

2、type 04. Update boilerplate. Editorial changes throughout. 96-07-09 M. L. Poelking E Add case outlines T and M. Changes to boilerplate. Editorial changes throughout. 96-10-03 M. L. Poelking F Changes in accordance with NOR 5962-R296-97. 97-06-06 M. L. Poelking G Add device type 05. Editorial changes

3、 throughout. - LTG 97-12-01 M. L. Poelking H Changes in accordance with NOR 5962-R103-98 98-05-06 M. L. Poelking J Changes in accordance with NOR 5962-R171-98 98-10-22 M. L. Poelking K Changes in accordance with NOR 5962-R002-00 99-11-15 M. L. Poelking L Incorporate revisions H, J, and K. Add paragr

4、aph 6.7, application note, to document. Update boilerplate to MIL-PRF-38535 requirements. LTG 02-06-17 Thomas M. Hess M Update die dimensions and bond pad coordinates due to die shrink. Update boilerplate to current MIL-PRF-38535 requirements. CFS 04-08-27 Thomas M. Hess N Update boilerplate to curr

5、ent MIL-PRF-38535 requirements. CFS 08-11-17 Thomas M. Hess REV N N N N SHEET 55 56 57 58 REV N N N N N N N N N N N N N N N N N N N N SHEET 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 REV N N N N N N N N N N N N N N N N N N N N SHEET 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

6、 32 33 34 REV STATUS REV N N N N N N N N N N N N N N OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Christopher A. Rauch DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Tim H. Noh COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABL

7、E FOR USE BY ALL DEPARTMENTS APPROVED BY Don M. Cool MICROCIRCUIT, DIGITAL, CMOS, DIGITAL SIGNAL PROCESSOR, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-09-13 AMSC N/A REVISION LEVEL N SIZE A CAGE CODE 67268 5962-90526 SHEET 1 OF 58 DSCC FORM 2233 APR 97 5962

8、-E039-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90526 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL N SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing document

9、s two product assurance class levels consisting of high reliability (device classes Q and M) and appendix F of MIL-PRF-38535, “General provisions for TAB microcircuits” and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or

10、Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90526 01 M X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designat

11、orCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535,

12、appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 320C30 Digital signal processor, 28 MHz 02 320C

13、30 Digital signal processor, 25 MHz 03 320C30 Digital signal processor, 33 MHz 04 320C30 Digital signal processor, 40 MHz 05 320C30 Digital signal processor, 50 MHz 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Devic

14、e class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A and appendix F of MIL-PRF-38535 Q or V Certification and qualification to MIL-PRF-38535 and appendix F

15、 of MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style U See figure 1 196 Quad flat pack with non-conductive tiebar X CMGA7-P181 181 Pin grid array Y 1/ See figure 1 196 Leadless chi

16、p carrier Z 1/ See figure 1 196 Quad flat package T See figure 1 203 Environmentally protected tape automated bond M See figure 1 196 Tape automated bond _ 1/ Not available from an approved source of supply. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

17、S-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90526 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL N SHEET 3 DSCC FORM 2234 APR 97 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 and appendix F of MIL-PRF-38535 for device classes Q and V or MIL-PRF-3853

18、5, appendix A and appendix F of MIL-PRF-38535 for device class M. 1.3 Absolute maximum ratings. 2/ Supply voltage range (VDD) 3/ . -0.3 V dc to 7.0 V dc Input voltage range . -0.3 V dc to 7.0 V dc Output voltage range . -0.3 V dc to 7.0 V dc Continuous power dissipation 4/ 3.15 W Storage temperature

19、 range . -55C to +150C Junction temperature (TJ) Case outlines X and U: Device types 03, 04, and 05 +150C Junction temperature (TJ) Case outlines T and M: Device type 03 +125C Thermal resistance, junction to case (JC): Case X See MIL-STD-1835 Case U 1.5C/W Maximum die temperature rise for the die at

20、 100%: Cases T and M 0.09C/W Thermal resistance, junction to ambient (JA): Case U 29C/W 1.4 Recommended operating conditions. Supply voltages (VDD): Device type 01, 04 and 05 . 4.75 V dc min to 5.25 V dc max Device type 02 and 03 . 4.5 V dc min to 5.5 V dc max Supply voltages (CVSS, etc.) (VSS) . 0

21、V dc nominal High level input voltage (VIH): 5/ Except CLKX0 and CLKX1 2.1 V dc min to VDD+0.3 V dc max High level input voltage (VIH): 5/ Pins CLKX0 and CLKX1 2.2 V dc min to VDD+0.3 V dc max Low level input voltage (VIL) 5/ . -0.3 V dc min to 0.8 V dc max High level output current (IOH) . -300 A m

22、ax Low level output current (IOL) . 2 mA max CLKIN high level input voltage (VTH) 5/ 3.0 V dc min to VDD+0.3 V dc max Operating case temperature (TC) -55C min to +125C max _ 2/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum leve

23、ls may degrade performance and affect reliability. 3/ All voltage values are with respect to VSS. 4/ Actual operating power will be less. This value was obtained under specially produced worst-case test conditions, which are not sustained during normal device operation. These conditions consist of c

24、ontinuous parallel writes of a checkerboard pattern to both primary and expansion buses at the maximum rate possible. 5/ VIHmax, VILmin, and VTHmax are guaranteed from characterization but not tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-S

25、TANDARD MICROCIRCUIT DRAWING SIZE A 5962-90526 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL N SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of

26、this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS M

27、IL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online

28、 at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing ta

29、kes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535, and appendix F of

30、 MIL-PRF-38535 “General provisions for TAB microcircuits”, and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device cla

31、ss M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.1.1 Microcircuit die. For the requirements of microcircuit die, see appendix A to this document. 3.2 Design, construction, and physical dimensions. The design, construction, and ph

32、ysical dimensions shall be as specified in MIL-PRF-38535, appendix F of MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A, appendix F of MIL-PRF-38535 and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and

33、 on figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Functional block diagram. The functional block diagram shall be as specified on figure 3. 3.2.4 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as speci

34、fied on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature r

35、ange. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUI

36、T DRAWING SIZE A 5962-90526 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL N SHEET 5 DSCC FORM 2234 APR 97 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire

37、 SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535 and appendix F

38、 of MIL-PRF-38535 (see 3.1 herein). Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A and appendix F of MIL-PRF-38535. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compl

39、iance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herei

40、n). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing sha

41、ll affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535, appendix F of MIL-PRF-38535 (see 3.1 herein) and herein or for device class M, the requirements of MIL-PRF-38535, appendix A, appendix F of MIL-PRF-38535, and herein. 3.7 Certificate of con

42、formance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notificatio

43、n to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufa

44、cturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 105 (see MIL-PRF-3

45、8535, appendix A). 3.11 ROM coding processing option. If ROM coding is to be utilized by the user, an altered item drawing (AID) must be supplied to the vendor. It is recommended that users insure the vendor perform subgroups 7 and 9 after programming to verify the specific program configuration. Pr

46、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90526 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL N SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Tes

47、t Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxHigh level output voltage VOHVDD= min IOH= -300.0 A 1, 2, 3 All 2.4 V VDD= min IOL= 2.0 mA 0.6 V Low level output voltage 2/ VOLFor pins A23-A0 1, 2, 3 All 0.8 V Three-state current IZVDD

48、= max 1, 2, 3 All -20.0 20.0 A Input current IINVIN= 0.0 V to VDDmax 1, 2, 3 All -10.0 10.0 A Input current with internal pull-ups 3/ IIP1, 2, 3 All -600.0 20.0 A Input current, (X2/CLKIN) IICVIN= 0.0 V to 5.5 V 1, 2, 3 All -50.0 50.0 A fx= 28 MHz 01 600.0 fx= 25 MHz 02 600.0 fx= 33 MHz 03 600.0 fx=

49、 40 MHz 04 600.0 Supply current 4/ ICCVDD= max fx= 50 MHz 1 05 600.0 mA Input capacitance 5/ CIN 15.0 Output capacitance 5/ COUT 20.0 X2/CLKIN capacitance 5/ CXSee 4.4.1b 4 All 25.0 pF Functional testing See 4.4.1d 7, 8 All Fall time, CLKIN 5/ tF1See figure 4 X2/CLKIN timing 9, 10, 11 All 5.0 ns tC1= 35 ns 01 12.5 tC1= 40 ns 02 14.