1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add case outline Y. Rewrite entire document. 93-06-11 K. A. Cottongim B Changes in accordance with NOR 5962-R158-95. 95-06-16 K. A. Cottongim C Changes in accordance with NOR 5962-R157-97. 96-12-20 K. A. Cottongim D Update drawing to current requ
2、irements of MIL-PRF-38534. 06-02-13 Raymond Monnin REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve Duncan DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Robert M. Heber POST OFFICE BOX
3、 3990 COLUMBUS, OHIO 43218-3390 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, HYBRID, LINEAR, RESOLVER OR SYNCHRO-TO-DIGITAL CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 90-10-10 AMSC N/A REVISION
4、 LEVEL D SIZE A CAGE CODE 67268 5962-90554 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E269-06Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90554 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISI
5、ON LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents one product assurance class, class H (high reliability) and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). 1.2 PIN. The PIN shall be as shown in t
6、he following example: 5962-90554 01 X X Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The device type(s) shall identify the circuit function as follows: Device type Generic number Circuit function Accuracy (1.0 LSB) 01 HSDC-8915A, XDC14
7、507-628 400 Hz, voltage follower buffer input 2.6 arc minutes 02 HSDC-8915, XDC14507-627 400 Hz, voltage follower buffer input 4.0 arc minutes 1.2.2 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package sty
8、le X See figure 1 36 Dual-in-line Y See figure 1 36 Dual-in-line 1.2.3 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) +18 V dc Logic input voltage (VL) +15 V dc Reference input 130 V rms Digital inputs -0.3 V dc to VL Power d
9、issipation (PD) . 270 mW 2/ Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds). +300C Thermal resistance, junction-to-case (JC) . 8.0C/W Thermal resistance, junction-to-ambient (JA) 28C/W Junction temperature (TJ) +150C 1.4 Recommended operating conditions. Supply volta
10、ge range (VS) +11 V dc to +16.5 V dc Logic input voltage (VL) +4.5 V dc to +15 V supply Case operating temperature range (TC). -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawi
11、ng to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and
12、affect reliability. 2/ Power dissipation applies up to TC= +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90554 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC F
13、ORM 2234 APR 97 DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDB
14、OOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Build
15、ing 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemp
16、tion has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device class H shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality
17、 Management (QM) plan or as designated for applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the
18、 QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall
19、 be in accordance with 1.2.2 herein and on figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Block diagram(s). The block diagram(s) shall be as specified on figure 3. 3.2.4 Digital angle output(s). The digital angle output(s) shall be as specifie
20、d on figure 4. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements
21、 shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor
22、similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each devi
23、ce type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon reques
24、t. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 a
25、nd herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRA
26、WING SIZE A 5962-90554 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device types Min Max Unit Resolu
27、tion control 14 bits fail/pass 7,8 All Output accuracy Measured at angles of 0, 15, 30, 45, 60, 75, 90, 105, 120, 135, 150, 165, 180, 225, 270, and 315 degrees 7,8 All 2/ Reference input Input voltage range 3/ VIN 4,5,6 All 4.0 130 V rms Carrier frequency 3/ 4,5,6 All 360 1000 Hz Single ended 250 In
28、put impedance 3/ ZINREFDifferential 4,5,6 All 500 k Common mode voltage range 3/ VCMREF4,5,6 All -210 210 V (pk) Signal input Input impedance 3/ ZINVoltage follower 4/ 4,5,6 All 10 M Sine/Cosine voltage 3/ range VINL-L Line-to-line 4,5,6 All 0.9 1.1 V rms Digital outputs (bits 1 through 14 and conve
29、rter busy) VOLLogic 0, 1 TTL load at -1.6 mA 1,2,3 All 0.4 V dc VOHLogic 1, 10 TTL loads at 0.4 mA 1,2,3 All 2.8 V dc Drive capability IXHigh impedance load 1,2,3 All -10 +10 A Converter busy CB Positive pulse 9,10,11 All 0.5 2.5 s See footnotes at end of table. Provided by IHSNot for ResaleNo repro
30、duction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90554 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditi
31、ons 1/ -55C TC +125C unless otherwise specified Group A subgroups Device types Min Max Unit Analog output Ac error e For 1.0 LSB change, near null to ground 4,5,6 All 12.8 19.2 mV rms/ LSB DC velocity voltage At 2.1 rps 4,5,6 All 0.8 1.2 V dc Filtered dc error 3/ E Per + lsb of error 4,5,6 All -1.2
32、-0.8 V dc Full scale max., positive direction 4,5,6 All 3.72 5.70 V dc Velocity 3/ 5/ v Full scale max., negative direction 4,5,6 All -3.73 -5.70 V dc Digital inputs (INH, EN 1-6, EN 7-14, and digital bits 1 through 14 while operating in CT mode) VILLogic 0, VL= 5.0 V dc 1,2,3 All 1.5 V dc Voltage i
33、nputs 6/ VIHLogic 1, VL= 5.0 V dc 1,2,3 All 3.5 V dc Loading 6/ ILOAD(internal pull-up) 1,2,3 All -1.0 -10 A Inhibit INH 7,8 7/ All Enable bits 1 to 6 EM 7,8 8/ All Enable bits 7 to 14 EL 7,8 8/ All Set S 7,8 9/ All See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or netwo
34、rking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90554 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -55C TC +
35、125C unless otherwise specified Group A subgroups Device types Min Max Unit Power supplies Supply current ISLogic = 0, VS= 16.5 V dc 1,2,3 All 25 mA Logic supply current ILVL= 5.0 V dc 1,2,3 All 1.0 mA 1/ VS= +11 V dc to +16.5 V dc, VL= +4.5 V dc to +15 V supply. 2/ Output accuracy for device type 0
36、1 is 2.6 arc minutes 1.0 LSB, and output accuracy for device type 02 is 4.0 arc minutes 1.0 LSB. 3/ Parameter shall be tested as part of device initial characterization and after design and process changes. Parameter shall be guaranteed to the limits specified in table I for all lots not specificall
37、y tested. 4/ The Sine/Cosine resolver signal is referenced to the converter internal dc reference (VREF). 5/ Test is performed at full speed of 10 rps. 6/ Test on a go-no-go basis in conjunction with other tested parameters and not directly testable. 7/ Test should verify no digital angles change wh
38、ile INH is logic 0 and analog input is rotating. 8/ Test should verify logic 0 enables, logic 1 high impedance. 9/ Test should verify logic 0 for use in CT mode. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 596
39、2-90554 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Inches mm Inches mm .005 0.13 .100 2.54 .010 0.25 .210 5.33 .015 0.38 .240 6.10 .018 0.46 .600 15.24 .055 1.40 .775 19.69 .086 2.18 1.700 43.18 .090 2.29 1.895 48.13 NOTES:
40、 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Lead identification numbers are for reference only. 4. Lead spacing dimensions apply only at seating plane. FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted w
41、ithout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90554 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 Case outline Y. Millimeters Inches Symbol Minimum Maximum Minimum Maximum A - 5.33 - .210 b 0.41 0.51 .016 .020 c 0.41 0
42、.51 .016 .020 D - 48.26 - 1.900 E - 20.32 - .800 e 2.54 BSC .100 BSC eA 15.11 15.37 .595 .605 L 6.10 6.60 .240 .260 Q - 0.72 .030 S1 2.18 2.44 .086 .096 X 43.18 BSC 1.700 BSC NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound units
43、 of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. FIGURE 1. Case outline(s) - Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZ
44、E A 5962-90554 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 APR 97 Device types 01 and 02 Device types 01 and 02 Case outlines X and Y Case outlines X and Y Terminal number Terminal symbol Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12
45、13 14 15 16 17 18 NC COSINE SINE NC BIT 1 MSB BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 BIT 8 BIT 9 BIT 10 BIT 11 BIT 12 BIT 13 BIT 14 LSB 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 RH (reference high) RL (reference low) NC E (filtered dc error out) (analog velocity out) CB (converter busy) EN
46、7-14 (enable, bits 7-14) EN 1-6 (enable, bits 1-6) e (AC error out) VL (logic voltage input) GND S Ge (gain control) VS(power supply in) INH (inhibit) VREF(internal dc reference) BC (buffered cosine) BS (buffered sine)FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or ne
47、tworking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90554 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 10 DSCC FORM 2234 APR 97 FIGURE 3. Block diagram(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90554 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 11 DSCC FORM 2234 APR 97 FIGURE 3. Block diagram(s) - Continued. Provided by IHSNot for ResaleNo reproduction or
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1