DLA SMD-5962-90628 REV B-2005 MICROCIRCUIT LINEAR TRAPEZOIDAL-WAVEFORM INTERFACE BUS TRANSCEIVERS MONOLITHIC SILICON《硅单片 梯形波形接口的总线收发器 线性微型电路》.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R022-94. 94-05-06 Michael A. Frye B Redraw. Incorporate rev. A changes. Update drawing to current requirements. Editorial changes throughout. - drw 05-10-27 Raymond Monnin THE ORIGINAL FIRST SHEET OF THIS DRAWI

2、NG HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Charles E. Besore COLUMBUS, OHIO 43218-3990 http:/www.dscc.

3、dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica Poelking MICROCIRCUIT, LINEAR, TRAPEZOIDAL-WAVEFORM INTERFACE BUS TRANSCEIVERS, AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-02-15 MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268

4、 5962-90628 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E479-05 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90628 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2

5、234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-90628 01 R A Drawin

6、g number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type. The device type identifies the circuit function as follows: Device type Generic number Circuit function 01 55ALS056 Trapezoidal-waveform interface bus transceivers 1.2.2 Case outlines. The case outlines

7、 are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 dual-in-line S GDFP2-F20 or CDFP3-F20 20 flat pack 2 CQCC1-N20 20 leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, ap

8、pendix A. 1.3 Absolute maximum ratings. Supply voltage (VCC) 6.0 V dc Control input voltage 5.5 V dc Driver input voltage 5.5 V dc Driver output voltage 2.5 V dc Receiver input voltage . 2.5 V dc Receiver output voltage . 5.5 V dc Continuous power dissipation (PD) 1/: Case R and 2 . 1375 mW Case S .

9、 1000 mW Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds) 300C Junction temperature (TJ) 150C 1.4 Recommended operating conditions. Supply voltage range (VCC) 4.5 V dc minimum to 5.5 V dc maximum Minimum high-level input voltage (VIH). 2.0 V dc Maximum low-level input

10、 voltage (VIL) . 0.8 V dc Bus termination voltage . 1.9 V dc to 2.1 V dc Ambient operating temperature range (TA) -55C to +125C _ 1/ For operation above +25C free-air temperature, derate case outlines R and 2 at the rate of 11 mW/C and case S at 8 mW/C. Provided by IHSNot for ResaleNo reproduction o

11、r networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90628 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following sp

12、ecification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General

13、 Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Draw

14、ings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the

15、 text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall

16、 be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification

17、to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modi

18、fications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimen

19、sions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections and truth table. The terminal connections and truth table shall be as sp

20、ecified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirem

21、ents shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be m

22、arked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in complianc

23、e to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAND

24、ARD MICROCIRCUIT DRAWING SIZE A 5962-90628 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Uni

25、t Min MaxHigh-level output voltage at An VOHVCC= 4.5 V, Bn at 1.2 V, IOH= -400 A, T/ R at 0.8 V, CS at 0.8 V 1, 2, 3 All 2.4 V Low-level output voltage An VOLVCC= 4.5 V, Bn at 2 V, IOL= 16 mA, T/ R at 0.8 V, CS at 0.8 V 1, 2, 3 All 0.5 V Bn VCC= 4.5 V, An at 2 V, T/ R at 2 V, CS at 0.8 V 0.75 1.2 In

26、put clamp voltage at An, T/ R and CS VICVCC= 4.5 V, II= -18 mA 1, 2, 3 All -1.5 V Receiver input threshold at Bn VTVCC= 5.0 V 1 All 1.45 1.65 V 2, 3 1.4 1.7 Short circuit output current at An IOSVCC= 5.5 V, Bn at 1.2 V, An at 0.0 V, T/ R at 0.8 V, CS at 0.8 V 1, 2, 3 All -35 -125 mA High-level input

27、 current An, T/ R and CS IINVCC= 5.5 V, VI= VCC1, 2, 3 All 40 A Bn VCC= 5.5 V, VI= 2.0 V, An at 0.8 V, T/ R at 0.8 V 100 Low-level input current at An, T/ R and CS IILVCC= 5.5 V, VI= 0.4 V 1, 2, 3 All -400 A Supply current ICCVCC= 5.5 V 1, 2, 3 All 85 mA Functional tests 1/ See 4.3.1c 7, 8 All See f

28、ootnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90628 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical perf

29、ormance characteristics - continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxDriver tPLH19 01 10 ns Propagation delay time, from An to Bn VCC= 4.5 V to 5.5 V, VL= 2.0 V, See figure 2 10, 11 45 tPHL19 12 10, 11 15 tPLH29 01 18 n

30、s Propagation delay time, from CS to Bn VCC= 4.5 V to 5.5 V, VL= 2.0 V, See figure 2 10, 11 45 tPHL29 20 10, 11 22 tPLH39 01 18 ns Propagation delay time, from RT/ to Bn VCC= 4.5 V to 5.5 V, VL= 2.0 V, See figure 3 10, 11 45 tPHL39 18 10, 11 21 tTLH9 01 8 ns Transition time, from An to Bn VCC= 4.5 V

31、 to 5.5 V, VL= 2.0 V, See figure 2 10, 11 38 tTHL9 10 10, 11 13 Receiver tPLH49 01 20 ns Propagation delay time, from Bn to An VCC= 4.5 V to 5.5 V, VL= 5.0 V, S1 closed, See figure 4 10, 11 22 tPHL49 18 10, 11 24 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networki

32、ng permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90628 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions -55C TA +125C unless o

33、therwise specified Group A subgroups Device type Limits Unit Min MaxReceiver tPLZ19 01 20 ns Output disable time, from CS to An VCC= 4.5 V to 5.5 V, VL= 5.0 V, S1 closed, See figure 5 10, 11 23 tPZL19 13 Output enable time, from CS to An 10, 11 14 tPHZ19 01 12 ns Output disable time, from CS to An V

34、CC= 4.5 V to 5.5 V, S1 open, See figure 5 10, 11 13 tPZH19 14 Output enable time, from CS to An 10, 11 22 tPLZ29 01 17 ns Output disable time, from RT/ to An VCC= 4.5 V to 5.5 V, VL= 5.0 V, S1 closed, See figure 5 10, 11 20 tPZL29 25 Output enable time, from RT/ to An 10, 11 45 tPHZ29 01 12 ns Outpu

35、t disable time, from RT/ to An VCC= 4.5 V to 5.5 V, VL= 0.0 V, S1 closed, See figure 5 10, 11 13 tPZH29 01 15 ns Output enable time, from RT/ to An VCC= 4.5 V to 5.5 V, S1 open, See figure 5 10, 11 22 tw(NR) 9 01 4 ns Receiver noise rejection pulse duration from Bn to An VCC= 4.5 V to 5.5 V, VL= 5.0

36、 V, S1 closed, See figure 6 10, 11 2 1/ Functional test shall be conducted at input test condition of GND VIL VOLand VOH VIH VCC. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90628 DEFENSE SUPPLY CENTER CO

37、LUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outline R, S, and 2 Terminal number Terminal symbol 1 A1 2 A2 3 A3 4 A4 5 VCC6 A5 7 A6 8 A7 9 A8 10 CS 11 RT/ 12 B8 13 B7 14 B6 15 B5 16 GND 17 B4 18 B3 19 B2 20 B1 Controls Channels CS RT/ A B L H T(

38、A B) L L R(B A) H X D NOTE: H = high level L = low level R =recive TtansmtD = disable Xirelvant FIGURE 1. Terminal connections and truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90628 DEFENSE SU

39、PPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 NOTE: For VI( CS ), tr= tf 5 ns from 10% to 90%. FIGURE 2. Driver delay waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRA

40、WING SIZE A 5962-90628 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 NOTE: For VI( RT/ ), tr= tf 5 ns from 10% to 90%. FIGURE 3. Bn to RT/ from forms Delay wave . Provided by IHSNot for ResaleNo reproduction or networking permitted without li

41、cense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90628 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 NOTE: For VI(Bn), tr= tf 10 ns from 10% to 90%. FIGURE 4. Receiver delay waveforms. Provided by IHSNot for ResaleNo reproduction

42、 or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90628 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 11 DSCC FORM 2234 APR 97 NOTE: For VI( CS , RT/ ), tr= tf 5 ns from 10% to 90%. FIGURE 5. Anto RT/ or CS from formsDel

43、ay wave . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90628 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 12 DSCC FORM 2234 APR 97 NOTE: For VI(Bn), tr= tf 2 ns from 10%

44、to 90%. FIGURE 6. Receiver noise immunity waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90628 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 13 DSCC FORM 2234 APR

45、 97 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affir

46、m that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Noti

47、fication of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore document

48、ation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspectio