DLA SMD-5962-90652 REV B-2012 MICROCIRCUIT DIGITAL HIGH SPEED CMOS 8-INPUT MULTIPLEXER TTL COMPATIBLE INPUTS MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add notes and redraw the switching waveforms for figure 4, switching waveforms and test circuit. Update boilerplate to MIL-PRF-38535 requirements. Editorial changes throughout. - LTG 06-01-31 Thomas M. Hess B Correct output current condition for

2、VOHand VOLtests in table I. Update boilerplate to MIL-PRF-38535 requirements. Editorial changes throughout. - jak 12-02-23 Thomas M. Hess REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Marcia B. Kelleher DLA LAND AND MA

3、RITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING CHECKED BY Thomas J. Riccuiti THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, HIGH SPEED CMOS, 8-INPUT MULTIPLEXER, TTL COMPATIBLE INPUTS, MONOLITH

4、IC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-04-19 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-90652 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E182-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD

5、MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-90652 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device cl

6、ass V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90652 01 M E A Fed

7、eral stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are m

8、arked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as fo

9、llows: Device type Generic number Circuit function 01 54HCT151 8-input multiplexer, TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-cer

10、tification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline lett

11、er Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) -0.5

12、V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC+ 0.5 V dc DC output voltage range (VOUT) . -0.5 V dc to VCC+ 0.5 V dc Clamp diode current 20 mA DC output current (per pin) 25 mA DC VCCor GND current (per pin) . 50 mA Storage temperature range (TSTG) . -65C to +150C Maximum power diss

13、ipation (PD) 2/ . 500 mW Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAN

14、D AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-90652 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. 3/ Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Input voltage range (VIN) 0.0 V dc to VCCOutput voltage range (VOUT) 0.0 V dc to VCCCase operating temp

15、erature range (TC) . -55C to +125C Input rise or fall time (tr, tf): VCC= 4.5 V, 5.5 V 0 to 500 ns 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless

16、otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL

17、-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from

18、the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in

19、 the solicitation or contract. JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JESD-7-A - Standard for Description of 54/74HCXXXX and 54/74HCTXXXX High-Speed CMOS Devices. (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 N

20、orth 10th Street, Suite 240S, Arlington, VA 22201.) 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

21、specific exemption has been obtained. 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ For TC= +100C to +125C, derate linearly at 12 mW/C. 3/ Unless otherwise specified,

22、 all voltages are referenced to ground. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-90652 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1

23、 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as de

24、scribed herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specif

25、ied in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Tr

26、uth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4. 3.3 Electrical performance characteristics a

27、nd postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test re

28、quirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN num

29、ber is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class

30、M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Ce

31、rtificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in

32、order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V,

33、the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall

34、be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects

35、this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made availa

36、ble onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 39 (see MIL-PRF-38535, appendix A). . Provided by IHSNot for ResaleNo reproduction or networking permitted without li

37、cense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-90652 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Test conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups

38、 Device type Limits Unit Min Max High level output voltage VOHVCC= 4.5 V VIN= VIH= 2.0 V or VIL= 0.8 V IOH= -20 A 1, 2, 3 All 4.4 V IOH= -4.0 mA 3.7 Low level output voltage VOLVCC= 4.5 V VIN= VIH= 2.0 V or VIL= 0.8 V IOL= +20 A 1, 2, 3 All 0.1 V IOL= +4.0 mA 0.4 High level input voltage VIH2/ VCC=

39、4.5 V 1, 2, 3 All 2.0 V Low level input voltage VIL2/ VCC= 4.5 V 1, 2, 3 All 0.8 V Quiescent supply current ICCVCC= 5.5 V, VIN= VCCor GND IOUT= 0.0 A 1, 2, 3 All 160 A Input leakage current IINVCC= 5.5 V, VIN= VCCor GND 1, 2, 3 All 1.0 A Additional quiescent supply current, TTL inputs ICCAny one inp

40、ut VIN= 2.4 V or 0.5 V Other inputs VIN= VCCor GND VCC= 5.5 V 1, 2, 3 All 3.0 mA Input capacitance CINVIN= 0 V, see 4.4.1c 4 All 10 pF Power dissipation capacitance CPD3/ See 4.4.1c 4 All 73 pF Functional tests See 4.4.1b 7, 8 All Propagation delay time, Im to Y tPHL1, tPLH1VCC= 4.5 V CL= 50 pF See

41、figure 4 9 All 38 ns 10, 11 57 Propagation delay time, Im to Y tPHL2, tPLH24/ 9 All 36 ns 10, 11 54 Propagation delay time, Sn to Y tPHL3, tPLH34/ 9 All 41 ns 10, 11 62 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ST

42、ANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-90652 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Test conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device typ

43、e Limits Unit Min Max Propagation delay time, Sn to YtPHL4, tPLH4VCC= 4.5 V CL= 50 pF See figure 4 9 All 43 ns 10, 11 65 Propagation delay time, ENABLEto Y tPHL5, tPLH54/ 9 All 29 ns 10, 11 44 Propagation delay time, ENABLEto YtPHL6, tPLH6 9 All 36 ns 10, 11 54 Transition time tTHL, tTLH4/ 9 All 15

44、ns 10, 11 22 1/ For a power supply of 5.0 V 10%, the worst case output voltages (VOHand VOL) occur for HCT at VCC= 4.5 V. Thus, the 4.5 V values should be used when designing with this supply. Worst cases VIHand VILoccur at VCC= 5.5 V and 4.5 V, respectively. 2/ Test is guaranteed if applied as a fo

45、rcing function for VOHor VOLtests. 3/ Power dissipation capacitance (CPD) determines the dynamic power consumption (PD) and the dynamic current consumption (IS): PD(total) = (CPD+ CL) VCC2f + (VCCx ICC) + (n x d x ICCx VCC) IS= (CPD+ CL) VCC f + ICC+ (n x d x ICC) f is input switching frequency; n i

46、s number of inputs switching; d is duty cycle; CLis load capacitance on each output. 4/ This parameter, if not tested, shall be guaranteed to the limits specified in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWI

47、NG DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-90652 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Device type All Case outline E Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 I3 I2 I1 I0 Y YENABLEGND S2 S1 S0 I7 I6 I5 I4 VCCFIGURE 1. Terminal connections. P

48、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-90652 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Inputs Outputs ENABLES2 S1 S0 I0 I1 I2 I3 I4 I5 I6 I7 Y Y H X X X X X X X X X X X H L L L L L L X X X X X X X H L L L L L H X X X X X X X L H L L L H X L X X X X X X H L L L L H X H X X X X X X L H L L H L X X L