DLA SMD-5962-90737 REV E-2011 MICROCIRCUIT LINEAR ANALOG SWITCH MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with N.O.R. 5962-R062-94. 93-12-06 M. A. Frye B Redrawn. Add case outline X. Technical and editorial changes throughout. 95-03-24 M. A. Frye C Drawing updated to reflect current requirements. - ro 01-10-02 R. Monnin D Redraw

2、n. Paragraph 1.2.2, correct circuit function for device type 03. Editorial changes throughout. - drw 10-10-12 Charles F. Saffle E Add new device types 04, 05, 06. - jt 11-06-23 C. SAFFLE REV SHEET REV E E SHEET 14 15 REV STATUS REV E E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12

3、 13 PMIC N/A PREPARED BY Dan Wonnell DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Sandra Rooney APPROVED BY Michael A. Frye MICROCIRCUIT,

4、LINEAR, ANALOG SWITCH, MONOLITHIC SILICON DRAWING APPROVAL DATE 93-05-06 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-90737 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E267-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUI

5、T DRAWING SIZE A 5962-90737 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A c

6、hoice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90737 01 M P A Federal stock

7、class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with

8、the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device types. The device types identify the circuit function as follows: Device t

9、ype Generic number Circuit function 01 DG417A CMOS, SPST analog switch 02 DG418A CMOS, SPST analog switch 03 DG419A CMOS, SPDT analog switch 04 DG417B CMOS, SPST analog switch 05 DG418B CMOS, SPST analog switch 06 DG419B CMOS, SPDT analog switch 1.2.3 Device class designator. The device class design

10、ator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification

11、and qualification to MIL-PRF-38535 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style H GDFP1-F10 or CDFP2-F10 10 Flat pack P GDIP1-T8 or CDIP2-T8 8 Dual-in-line X CDFP3-F10 10 Flat pack 1.2.5 Lead fi

12、nish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90737 DLA LAND AND MARITIME C

13、OLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage between V+ and V- . 44 V dc Device types 01, 02 and 03 Supply voltage between V+ and V-. 20 V dc Device types 04, 05 and 06 Supply voltage between GND and V- . 25 V dc Digital inpu

14、ts range to V- . (GND - 0.3 V dc) to 44 V dc 2/ Device types 01, 02 and 03 Digital inputs range to V-. (GND 0.3 V dc) to (V+) + 0.3 V 2/ Device types 04, 05 and 06 Digital input range VS, VDto V- . (V-) -2 V dc to (V+) +2 V dc or 30 mA, whichever occurs first 2/ Current (any terminal except for S an

15、d D) continuous 30 mA Current (S or D) pulsed, 1 ms, 10% duty cycle . 100 mA Power dissipation (PD): Cases H and X, at +70C 421 mW 3/ Case P at +75C 600 mW 3/ Junction temperature (TJ) . +175C Lead temperature (soldering, 10 seconds ) +300C Storage temperature range. -65C to +150C Thermal resistance

16、, junction-to-case (JC) See MIL-STD-1835 1.4 Recommended operating conditions. Positive supply voltage (V+) . +15 V dc Negative supply voltage (V-) . -15 V dc Logic supply voltage (VL) 5 V dc Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification,

17、 standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 -

18、Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the dev

19、ice. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Signals on SX, DX, or INXexceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to the maximum current ratings. 3/ For case outlines H and X, derate above TA= +70C linearly at

20、 5.26 mW/C. For case outline P, device types 01, 02 and 03, derate above TA= +75C linearly at 12 mW/C. For case outline P, device types 04, 05 and 06, derate above TA = +75 C linearly at 8 mW/C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDAR

21、D MICROCIRCUIT DRAWING SIZE A 5962-90737 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are

22、 available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

23、of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535

24、and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A

25、for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2

26、.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation p

27、arameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall

28、be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasib

29、le due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in acc

30、ordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of comp

31、liance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be liste

32、d as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements

33、of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with

34、each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. Pro

35、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90737 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol C

36、onditions 1/ -55C TA +125C Group A subgroups Device type Limits Unit unless otherwise specified Min Max Drain-source ON resistance rDS(ON)IS= -10 mA, VD= 12.5 V, VIN= 0.8 V, VL= 5V V+ = +13.5 V, V- = -13.5 V 1 01 2.5 35 2, 3 2.5 45 IS = -10 mA, VD = 12.5 V, VIN= 2.4 V, VL= 5 V V+ = +13.5 V, V- = -13

37、.5 V 1 02 2.5 35 2, 3 2.5 45 IS= -10 mA, VD= 12.5 V, VIN= 0.8 V, 2.4 V, VL= 5 V 2/ V+ = +13.5 V, V- = -13.5 V 1 03 2.5 35 2, 3 2.5 45 IS= -10 mA, VD= + 12.5 V VIN= 0.8 V, VL= 5 V V+ = 13.5 V, V- = -13.5 V 1 04 2.5 25 2, 3 2.5 34 IS= -10 mA, VD= + 3.8 V VIN= 2.4 V, VL = 5 V V+ = 10.8 V, V- = 0 V 1 04

38、 2.5 35 2, 3 2.5 52 IS= -10 mA, VD= +12.5 V VIN= 2.4 V, VL= 5 V V+ = 13.5V, V- = -13.5 V 1 05 2.5 25 2, 3 2.5 34 IS= -10 mA, VD= + 3.8 V VIN= 0.8 V, VL= 5 V V+ = 10.8 V, V- = 0 V 1 05 2.5 35 2, 3 2.5 52 IS= -10 mA, VD= + 12.5 VIN= 0.8 V, 2.4 V, VL= 5 V V+ = 13.5 V, V- = -13.5V 1 06 2.5 25 2, 3 2.5 3

39、4 IS= -10 mA, VD= +3.8 V VIN= 0.8V, 2.4 V, VL= 5 V V+ = 10.8 V, V- = 0 V 1 06 2.5 35 2, 3 2.5 52 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90737 DLA LAND AND MARITIME COLU

40、MBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TA +125C Group A subgroups Device type Limits Unit unless otherwise specified Min Max Source OFF leakage current IS(OFF)VD= 15.5 V, VS= 15.

41、5 V, VIN= 2.4 V, V+ = +16.5 V, V- = -16.5 V 1 01, 04 0.25 nA 2, 3 20 VD= 15.5 V, VS= 15.5 V, VIN= 0.8 V, V+ = +16.5 V, V- = -16.5 V 1 02, 05 0.25 2, 3 20 VD= 15.5 V, VS= 15.5 V, VIN= 0.8 V, 2.4 V, 2/ V+ = +16.5 V, V- = -16.5 V 1 03, 06 0.25 2, 3 20 Drain OFF leakage current ID(OFF) VD= 15.5 V, VS= 1

42、5.5 V, VIN= 2.4 V, V+ = +16.5 V, V- = -16.5 V 1 01, 04 0.25 nA 2, 3 20 VD= 15.5 V, VS= 15.5 V, VIN= 0.8 V, V+ = +16.5 V, V- = -16.5 V 1 02, 05 0.25 2, 3 20 VD= 15.5 V, VS= 15.5 V, VIN= 0.8 V, 2.4 V, 2/ V+ = +16.5 V, V- = -16.5 V 1 03, 06 0.75 2, 3 60 See footnotes at end of table. Provided by IHSNot

43、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90737 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Cond

44、itions -55C TC +125C Group A subgroups Device type Limits Unit unless otherwise specified Min Max Drain ON leakage current ID(ON) VD= 15.5 V, VS= 15.5 V, VIN= 0.8 V, V+ = +16.5 V, V- = -16.5 V 1 01,04 0.4 nA 2, 3 40 VD= 15.5 V, VS= 15.5 V, VIN= 2.4 V, V+ = +16.5 V, V- = -16.5 V 1 02,05 0.4 2, 3 40 V

45、D= 15.5 V, VS= 15.5 V, VIN= 0.8 V, 2.4 V, 2/ V+ = +16.5 V, V- = -16.5 V 1 03, 06 0.75 2, 3 60 Logic input current, input voltage low IILVIN= 0.8 V 1, 2, 3 All 0.5 A Logic input current, input voltage high IIHVIN= 2.4 V 1, 2, 3 All 0.5 A Turn-ON time tON RL= 300 , CL= 35 pF, VS= 10 V, see figure 3 9

46、01, 02 10 175 ns 10, 11 10 250 RL= 300 , CL= 35 pF, VS= 10 V, see figure 3 9 04, 05 5 89 10, 11 5 106 RL= 300 , CL= 35 pF, VIN= 0.8 V, VL= 5 V V+ = 12 V, V- = 0 V, See figure 3 9 04, 05 2.5 125 10, 11 2.5 155 Turn-OFF time tOFF RL= 300 , CL= 35 pF, VS= 10 V, see figure 3 9 01, 02 10 145 ns 10, 11 10

47、 210 9 04, 05 5 80 10, 11 5 88 RL= 300 , CL= 35 pF, VIN= 0.8 V, VL= 5 V V+ = 12 V, V- = 0 V, See figure 3 9 04, 05 2.5 66 10, 11 2.5 73 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE

48、A 5962-90737 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions 1/ -55C TA +125C Group A subgroups Device type Limits Unit unless otherwise specified Min Max Transition time ttrans RL= 300 , CL= 35 pF, VS1= 10 V, VS2= 10 V, see figures 4 and 6 9 03 10 175 ns 10, 11 10 250 9 06 10 87 1