DLA SMD-5962-90749 REV B-2012 MICROCIRCUIT DIGITAL BIPOLAR CMOS OCTAL BUFFER AND LINE DRIVER WITH NONINVERTING THREE-STATE OUTPUTS TTL COMPATIBLE INPUTS MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Redraw the switching waveforms in figure 4, switching waveforms and test circuit. Update boilerplate to MIL-PRF-38535 requirements. Editorial changes throughout. LTG 06-04-21 Thomas M. Hess B Update boilerplate to MIL-PRF-38535 requirements. Edit

2、orial changes throughout. jak 12-06-01 Thomas M. Hess REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Marcia B. Kelleher DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIR

3、CUIT DRAWING CHECKED BY Thomas J. Ricciuti THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, BIPOLAR CMOS, OCTAL BUFFER AND LINE DRIVER WITH NONINVERTING THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMEN

4、T OF DEFENSE DRAWING APPROVAL DATE 90-10-10 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-90749 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E215-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90749 D

5、LA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and le

6、ad finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90749 01 M R A Federal stock class designator RHA designat

7、or (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designato

8、r. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circui

9、t function 01 54BCT541 Octal buffer and line driver with non-inverting three-state outputs, TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor

10、self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outl

11、ine letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2 CQCC1-N20 20 Square chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for

12、device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90749 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply vol

13、tage range (VCC) -0.5 V dc to +7.0 V dc Input voltage range (VIN) -0.5 V dc to +7.0 V dc Voltage applied to any output in the high state (VOUT) . -0.5 V dc to VCCVoltage applied to any output in the disabled state (VOUT) . -0.5 V dc to +5.5 V dc Current into any output in the low state . 96 mA Input

14、 clamp current (IIC) . -30 mA Storage temperature range (TSTG) . -65C to +150C Maximum power dissipation (PD) . 607 mW 2/ Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions.

15、Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Minimum high level input voltage (VIH) . 2.0 V dc Maximum low level input voltage (VIL) . 0.8 V dc Maximum high level output current (IOH) -12 mA Maximum low level output current (IOL) +48 mA Ambient operating temperature range (TC) -55C to +125C 1/

16、Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Must be able to withstand the additional PDdue to the short circuit test, e.g., IOS. The PDlimit is based upon dc values. P

17、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90749 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standa

18、rds, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integra

19、ted Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-H

20、DBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict bet

21、ween the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requiremen

22、ts for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements f

23、or device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes

24、 Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified o

25、n figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherw

26、ise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD

27、 MICROCIRCUIT DRAWING SIZE A 5962-90749 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined i

28、n table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on t

29、he device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certificati

30、on mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML

31、-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of com

32、pliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appen

33、dix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device

34、class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA

35、 Land and Maritime s agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device cla

36、ss M devices covered by this drawing shall be in microcircuit group number 126 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90749 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-

37、3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Test conditions -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max High level output voltage VOHVCC= 4.5 V VIH= 2.0 V or VIL= 0.8 V IOH= -3 mA 1, 2

38、, 3 All 2.4 V IOH= -12 mA 2.0 Low level output voltage VOLVCC= 4.5 V VIH= 2.0 V or VIL= 0.8 V IOL= 48 mA 1, 2, 3 All 0.55 V Input clamp voltage VICVCC= 4.5 V, IIN= -18 mA 1, 2, 3 All -1.2 V High level input current IIH1VCC= 5.5 V, VIN= 5.5 V 1, 2, 3 All 100 A IIH2VCC= 5.5 V, VIN= 2.7 V 20 A Low leve

39、l input current IILVCC= 5.5 V, VIN= 0.5 V 1, 2, 3 All -0.6 mA Short-circuit output current 1/ IOSVCC= 5.5 V, VOUT= 0.0 V 1, 2, 3 All -100 -225 mA Supply current, outputs high ICCHVCC= 5.5 V, outputs open 1, 2, 3 All 40 mA Supply current, outputs low ICCL72 Supply current, outputs disabled ICCZ7 Off-

40、state output current, high level voltage applied IOZHVCC= 5.5 V, VOUT= 2.7 V 1, 2, 3 All 50 A Off-state output current, low level voltage applied IOZLVCC= 5.5 V, VOUT= 0.5 V 1, 2, 3 All -50 A Functional tests 2/ See 4.4.1b 7, 8 All Propagation delay time, An to Yn tPLHCL= 50 pF R1 = R2 = 500 See fig

41、ure 4 VCC= 5.0 V 9 All 2.1 5.3 ns VCC= 4.5 V and 5.5 V 10, 11 1.7 6.3 tPHLVCC= 5.0 V 9 All 3.7 7.5 VCC= 4.5 V and 5.5 V 10, 11 3.2 8.7 Propagation delay time, output enable, OE1 or OE2 to Yn tPZHVCC= 5.0 V 9 All 5.3 9.3 ns VCC= 4.5 V and 5.5 V 10, 11 4.4 11.0 tPZLVCC= 5.0 V 9 All 6.0 10.4 VCC= 4.5 V

42、 and 5.5 V 10, 11 5.4 12.4 Propagation delay time, output disable, OE1 or OE2 to Yn tPHZVCC= 5.0 V 9 All 3.5 7.6 ns VCC= 4.5 V and 5.5 V 10, 11 3.0 9.1 tPLZVCC= 5.0 V 9 All 3.4 7.2 VCC= 4.5 V and 5.5 V 10, 11 3.0 9.4 See footnotes on next sheet.Provided by IHSNot for ResaleNo reproduction or network

43、ing permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90749 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. 1/ Not more than one output should be shorted at one ti

44、me and the duration of the test condition shall not exceed one second. 2/ Functional tests shall be conducted at input test conditions of 0.4 V VIL 0.8 V and 2.0 V VIH 2.4 V for VCC= 4.5 V and is repeated for VCC= 5.5 V. Device type All Case outlines R, S, and 2 Terminal number Terminal symbol 1 2 3

45、 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 OE1 A1 A2 A3 A4 A5 A6 A7 A8 GND Y8 Y7 Y6 Y5 Y4 Y3 Y2 Y1 OE2 VCCFIGURE 1. Terminal connections. Inputs Outputs OE1 OE2 An Yn L L L L L L H H H X X Z X H X Z H = High voltage level L = Low voltage level Z = High-impedance state X = Irrelevant FIGURE 2. Tru

46、th table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90749 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for R

47、esaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90749 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 FIGURE 4. Switching waveforms and test circuit. Provided by IHSNot for ResaleNo rep

48、roduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90749 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 NOTES: 1. When measuring tPLZand tPZL: S1 = 7.0 V. When measuring tPLH, tPHL, tPZH, and tPHZ: S1 = Open. 2. The tPZLand tPLZreference waveform is for the output under test with internal conditions such that the output is low at VOL except when dis