DLA SMD-5962-90750 REV B-2012 MICROCIRCUIT DIGITAL BIPOLAR CMOS OCTAL BUS TRANSCEIVER WITH INVERTING THREE-STATE OUTPUTS TTL COMPATIBLE INPUTS MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Redraw the switching waveforms in figure 4, switching waveforms and test circuit. Update boilerplate to MIL-PRF-38535 requirements. Editorial changes throughout. LTG 06-04-21 Thomas M. Hess B Update boilerplate paragraphs to the current MIL-PRF-3

2、8535 requirements. - LTG 12-06-22 Thomas M. Hess REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Marcia B. Kelleher DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWI

3、NG THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A CHECKED BY Thomas J. Ricciuti APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, , BIPOLAR CMOS, OCTAL BUS TRANSCEIVER WITH INVERTING THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS, MONOLITHIC SILI

4、CON DRAWING APPROVAL DATE 90-10-01 REVISION LEVEL B SIZE A CAGE CODE 67268 5962-90750 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E320-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90750 DLA LAND AND MARITI

5、ME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are av

6、ailable and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90750 01 M R A Federal stock class designator RHA designator (see 1.2.1) Dev

7、ice type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M

8、RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54BC

9、T620A Octal bus transceiver with inverting three-state outputs, TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the re

10、quirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive desig

11、nator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2 CQCC1-N20 20 Square chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by

12、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90750 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5

13、V dc to +7.0 V dc DC input voltage range (VIN): I/O ports . -0.5 V dc to +5.5 V dc Excluding I/O ports . -0.5 V dc to +7.0 V dc Voltage applied to any output in the high state (VOUT) . -0.5 V dc to VCCVoltage applied to any output in the disabled state (VOUT) . -0.5 V dc to +5.5 V dc Current into an

14、y output in the low state . 96 mA Input clamp current (IIC) . -30 mA Storage temperature range (TSTG) . -65C to +150C Maximum power dissipation (PD) . 673 mW 4/ Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C

15、 1.4 Recommended operating conditions. Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Minimum high level input voltage (VIH) . 2.0 V dc Maximum low level input voltage (VIL) . 0.8 V dc Maximum high level output current (IOH): A port . -3.0 mA B port . -12 mA Maximum low level output current (IOL)

16、: A port . +20 mA B port . +48 mA Case operating temperature range (TC) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise s

17、pecified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 -

18、 Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardizat

19、ion Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes appli

20、cable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise specified, all voltages are

21、 referenced to ground. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ Must be able to withstand the additional PDdue to the short circuit test, e.g., IOS. The PDlimit is based upon dc values. Provided by

22、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90750 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements

23、 for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for de

24、vice class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q an

25、d V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on fig

26、ure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise s

27、pecified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II

28、. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manuf

29、acturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A

30、. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a

31、certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in M

32、IL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for dev

33、ice class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to

34、 this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device cl

35、ass M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcir

36、cuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 126 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5

37、962-90750 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Test conditions -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max High level output voltage A

38、 port VOHVCC= 4.5 V VIH= 2.0 V VIL= 0.8 V IOH= -1 mA 1, 2, 3 All 2.5 V IOH= -3 mA 2.4 B port IOH= -3 mA 2.4 IOH= -12 mA 2.0 Low level output voltage A port VOLVCC= 4.5 V VIH= 2.0 V VIL= 0.8 V IOL= 20 mA 1, 2, 3 All 0.50 V B port IOL= 48 mA 0.55 Input clamp voltage VICVCC= 4.5 V, IIN= -18 mA 1, 2, 3

39、All -1.2 V High level input current 1/ A or B port IIH1VCC= 5.5 V, VIN= 5.5 V 1, 2, 3 All 1.0 mA OEAB or OEBA 0.1 A or B port IIH2VCC= 5.5 V, VIN= 2.7 V 70 A OEAB or OEBA 20 Low level input current 1/ A or B port IILVCC= 5.5 V, VIN= 0.5 V 1, 2, 3 All -0.65 mA OEAB or OEBA -0.60 Short-circuit output

40、current 2/ A port IOSVCC= 5.5 V, VOUT= 0.0 V 1, 2, 3 All -60 -150 mA B port -100 -225 Supply current, outputs high 3/ ICCHVCC= 5.5 V Outputs open 1, 2, 3 All 37 mA Supply current, outputs low 3/ ICCL84 Supply current, outputs disabled ICCZ10 Functional tests 4/ See 4.4.1b 7, 8 All ns Propagation del

41、ay time, Am to Bm tPLH1CL= 50 pF R1 = R2 = 500 See figure 4 VCC= 5.0 V 9 All 0.6 5.2 VCC= 4.5 V and 5.5 V 10, 11 0.6 6.2 tPHL1VCC= 5.0 V 9 All 0.1 3.4 VCC= 4.5 V and 5.5 V 10, 11 0.1 3.7 Propagation delay time, Bm to Am tPLH2VCC= 5.0 V 9 All 0.9 6.0 ns VCC= 4.5 V and 5.5 V 10, 11 0.9 7.2 tPHL2VCC= 5

42、.0 V 9 All 0.1 3.7 VCC= 4.5 V and 5.5 V 10, 11 0.1 4.0 Propagation delay time, output enable, OEBA to Am tPZH1VCC= 5.0 V 9 All 3.5 9.2 ns VCC= 4.5 V and 5.5 V 10, 11 3.5 10.9 tPZL1VCC= 5.0 V 9 All 3.7 9.9 VCC= 4.5 V and 5.5 V 10, 11 3.7 11.5 See footnotes at end of table. Provided by IHSNot for Resa

43、leNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90750 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Test conditions

44、 -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Propagation delay time, output enable, OEAB to Bm tPZH2CL= 50 pF R1 = R2 = 500 See figure 4 VCC= 5.0 V 9 All 2.0 6.7 ns VCC= 4.5 V and 5.5 V 10, 11 2.0 7.9 tPZL2VCC= 5.0 V 9 All 2.9 8.1 VCC= 4.5 V and 5.5 V 1

45、0, 11 2.9 9.2 Propagation delay time, output disable, OEBA to Am tPHZ1VCC= 5.0 V 9 All 3.1 8.6 ns VCC= 4.5 V and 5.5 V 10, 11 3.1 10.8 tPLZ1VCC= 5.0 V 9 All 1.3 6.9 VCC= 4.5 V and 5.5 V 10, 11 1.3 8.3 Propagation delay time, output disable, OEAB to Bm tPHZ2VCC= 5.0 V 9 All 2.1 7.0 ns VCC= 4.5 V and

46、5.5 V 10, 11 2.1 8.5 tPLZ2VCC= 5.0 V 9 All 0.1 5.3 VCC= 4.5 V and 5.5 V 10, 11 0.1 6.0 1/ For I/O ports, the parameters IIH2and IILinclude the off-state output current. 2/ Not more than one output should be shorted at one time and the duration of the test condition shall not exceed one second. 3/ IC

47、CHand ICCLare measured in the A to B mode. 4/ Functional tests shall be conducted at input test conditions of 0.4 V VIL 0.8 V and 2.0 V VIH 2.4 V for VCC= 4.5 V and is repeated for VCC= 5.5 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD

48、MICROCIRCUIT DRAWING SIZE A 5962-90750 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Device type All Case outlines R, S, and 2 Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 OEAB A1 A2 A3 A4 A5 A6 A7 A8 GND B8 B7 B6 B5 B4 B3 B2 B1 OEBA VCCFIGURE 1. Terminal connections. Inputs Operation OEBA OEAB L L B data to A bus L H B data to A bus, A data to B bus H L Isolation H H A data to B bus H = High voltage level L = Low voltage level FIGURE 2. Truth table. Provided by IHSNot f