DLA SMD-5962-90765 REV E-2011 MICROCIRCUIT LINEAR LINE DRIVER QUAD DIFFERENTIAL MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device types 03 and 04. Editorial changes throughout. 94-11-15 M. A. Frye B Changes in accordance with NOR 5962-R106-95. 95-04-12 M. A. Frye C Change tLZ, tHZ, and tTDfor device type 03 in table I. Editorial changes throughout. -rrp 98-10-05

2、Raymond Monnin D Update drawing to current requirements. Editorial changes throughout. - drw 04-11-18 Raymond MonninE Redraw. For device types 01 and 02, correct the RLtest condition in table I for tests VOD2, Delta VOD2, VOC, and Delta VOC, from 1000 to 100. - drw11-01-24 Charles F. Saffle THE ORIG

3、INAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV E SHET 15 REV STATUS REV E E E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Rick C. Officer DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRA

4、WING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Charles E. Besore APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, LINE DRIVER, QUAD DIFFERENTIAL, MONOLITHIC SILICON DRAWING APPROVAL DATE 91-08-01 AMSC N/A REVISION LEVEL E SIZE A CAGE C

5、ODE 67268 5962-90765 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E170-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90765 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2

6、234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN)

7、. When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90765 01 Q E A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.

8、4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA

9、levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device types. The device types identify the circuit function as follows: Device type Generic number Circuit function 01 96F172 RS-485 comparable quad differential line driver 02 96F174 RS-485 comp

10、arable quad differential line driver 03 55LBC172 RS-485 comparable quad differential line driver, low power 04 55LBC174 RS-485 comparable quad differential line driver, low power 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as

11、follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outlines. The case ou

12、tlines are as designated in MIL-STD-1835 as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F GDFP2-F16 or CDFP3-F16 16 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-

13、38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90765 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3

14、 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) 7 V dc Enable input voltage 5.5 V dc Storage temperature range . -65C to +150C Lead temperature (soldering, 60 seconds) +300C Junction temperature (TJ): Device type 01, 02 . +175C Device type 03, 04 . +150C Power dissipatio

15、n (PD), TA= +25C 2/, device types 01, 02: Case E . 1800 mW Case F . 1000 mW Case 2 2000 mW Power dissipation (PD), TA= +25C 3/, device types 03, 04: Case E, 2 . 1375 mW Case F . 1000 mW Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case E,

16、 device types 01, 02 80C/W Case E, device types 03, 04 85C/W Case F . 140C/W Case 2 75C/W 1.4 Recommended operating conditions. Operating supply voltage range (VCC): Device types 01, 02 4.5 V dc to 5.5 V dc Device types 03, 04 4.75 V dc to 5.25 V dc Ambient operating temperature range (TA) -55C to +

17、125C Common mode output voltage range (VOC) . -7 V dc to +12 V dc High output current (IOH) -60 mA Low output current (IOL) . 60 mA 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the

18、 extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test M

19、ethod Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.d

20、aps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affe

21、ct reliability. 2/ Above TA= +25C, derate at a factor of 12.5 mW/C for case E, 7.1 mW/C for case F and 13.4 mW/C for case 2. 3/ Above TA= +25C, derate at a factor of 11 mW/C for cases E and 2, 8 mW/C for case F. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

22、m IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90765 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing take

23、s precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified her

24、ein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class le

25、vel B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. Th

26、e case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth tables. The truth tables shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. U

27、nless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups s

28、pecified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space li

29、mitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-P

30、RF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device

31、 classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved s

32、ource of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 a

33、nd herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microc

34、ircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and

35、review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the rev

36、iewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 53 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCU

37、IT DRAWING SIZE A 5962-90765 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA+125C Group A subgroups Device type Limits Unit unless otherwise specified Min Max Low level i

38、nput voltage VILVCC= 5.5 V 1 01, 02 0.8 V 2, 3 0.7 VCC= 5.25 V 1, 2, 3 0.8 High level input voltage VIHVCC= 5.5 V 1, 2, 3 01, 02 2 V VCC= 5.25 V 03, 04 2 Input clamp voltage VICII= -18 mA, VCC= 5.5 V 1, 2, 3 01, 02 -1.5 V II= -18 mA, VCC= 5.25 V 03, 04 -1.5 Differential output voltage VOD1IO= 0 mA,

39、VCC= 5.5 V 1, 2, 3 01, 02 6 V VOD2RL= 54, VCC= 4.5 V 2/ 1, 2 01, 02 1.5 3 1.2 RL= 54, VCC= 4.75 V 2/ 1, 2, 3 03, 04 1.1 5.0 RL= 100, VCC= 4.5 V 2/ 1, 2, 3 01, 02 2.0 RL= 60, VCC= 4.75 V 2/ 03, 04 1.1 5.0 Change in magnitude of VOD23/ Delta VOD2RL= 54, VCC= 4.5 V 1, 2 01, 02 -200 200 mV RL= 100, VCC=

40、 4.5 V 4/ 3 -400 400 RL= 54, VCC= 4.75 V 1, 2, 3 03, 04 -200 200 Common mode output voltage VOCRL= 54, VCC= 5.5 V 1, 2, 3 01, 02 3 V RL= 100, VCC= 5.5 V 3 RL= 54, VCC= 5.25 V 03, 04 -1 3 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

41、se from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90765 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions 1/ -55C TA+125C Group A subgroups Device type Limits Unit

42、 unless otherwise specified Min Max Change in magnitude of VOC 3/ Delta VOCRL= 54, VCC= 4.5 V 1, 2, 3 01, 02 -200 200 mV RL= 100, VCC= 4.5 V -200 200 RL= 54, VCC= 4.75 V 03, 04 -200 200 Output current with power off IOVO= -7 V to 12 V, VCC= 0 V 1, 2, 3 01, 02 -50 50 A 03, 04 -100 100 High impedance

43、state output current IOZVO= -7 V to 12 V, VCC= 5.5 V, outputs disabled 1, 2, 3 01, 02 -50 50 A VO= -7 V to 12 V, VCC= 5.25 V, outputs disabled 03, 04 -100 100 Short circuit output current 5/ IOSVO= -7 V, VCC= 5.5 V 1, 2, 3 01, 02 -250 mA VO= -7 V, VCC= 5.25 V 03, 04 -250 VO= 12 V, VCC= 5.5 V 01, 02

44、250 VO= 12 V, VCC= 5.25 V 03, 04 250 VO= 0 V, VCC= 5.5 V 01, 02 -150 VO= VCC= 5.5 V 150 High input current IIHVI= 2.4 V, VCC= 5.5 V 1, 2, 3 01, 02 20 A VI= 2.4 V, VCC= 5.25 V 03, 04 -100 Low input current IILVI= 0.4 V, VCC= 5.5 V 1, 2, 3 01, 02 -50 A VI= 0.4 V, VCC= 5.25 V 03, 04 -100 Supply current

45、 (all drivers) ICCVCC= 5.5 V, no load, outputs enabled 1, 2, 3 01, 02 50 mA VCC= 5.25 V, no load, outputs enabled 03, 04 7 VCC= 5.5 V, no load, outputs disabled 01, 02 30 VCC= 5.25 V, no load, outputs disabled 03, 04 1.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or

46、networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90765 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions 1/ -55C TA+125C Group A

47、 subgroups Device type Limits Unit unless otherwise specified Min Max Functional test FT See 4.4.1b 7, 8 All Propagation delay low to high level tPLHRL= 27 , CL= 15 pF, VCC= 5 V, see figure 3 9 01, 02 16 ns 10, 11 25 Propagation delay high to low level tPHLRL= 27 , CL= 15 pF, VCC= 5 V, see figure 3

48、9 01, 02 16 ns 10, 11 25 Output disable time from low level tLZRL= 110 , CL= 50 pF, VCC= 5 V, see figure 3 9 01, 02 25 ns 03, 04 30 10, 11 01, 02 40 03 55 04 45 Output disable time from high level tHZRL= 110 , CL= 50 pF, VCC= 5 V, see figure 3 9 01, 02 30 ns 03 60 04 50 10, 11 01, 02 80 03 115 04 90 Output enable time to low level tZLRL= 110 , CL= 50 pF, VCC= 5 V, see figure 3 9 01, 02 40 ns 03, 04 30 10, 11 01, 02 100 03, 04 40 See footnotes at end of table. Provided by IHSNot