DLA SMD-5962-90927 REV G-2004 MICROCIRCUIT LINEAR ANALOG-TO-DIGITAL CONVERTER VIDEO 8-BIT MONOLITHIC SILICON《硅单块 8比特视频模拟到数字转换器 直线式微型电路》.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R261-92. 92-07-13 M. A. Frye B Redrawn with changes. Add device type 03. Editorial changes throughout. 95-07-17 M. A. Frye C Changes to table I. Editorial changes throughout. - drw 98-03-27 Raymond Monnin D Cha

2、nges to table I, sheet 5. - drw 99-02-26 Raymond Monnin E Change test conditions of supply current tests in table I for device types 01 and 02, sheet 5. - drw 99-09-16 Raymond Monnin F Change in table I, sheet 5, for device types 01 and 02. - drw 00-01-03 Raymond Monnin G Update drawing to current r

3、equirements. Editorial changes throughout. - drw 04-12-20 Raymond Monnin THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED REV SHET REV SHET REV STATUS REV G G G G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Dan Wonnell DEFENSE SUPPLY CENTER COL

4、UMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Charles E. Besore COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, ANALOG-TO-DIGITAL CONVERTER, VIDEO, 8-BIT, AND AGENCIES OF THE DEPARTMENT OF DEFENS

5、E DRAWING APPROVAL DATE 92-03-25 MONOLITHIC SILICON AMSC N/A REVISION LEVEL G SIZE A CAGE CODE 67268 5962-90927 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E053-05 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962

6、-90927 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of cas

7、e outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90927 01 Q X A Federal stock class desig

8、nator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropria

9、te RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device types. The device types identify the circuit function as follows: Device type Generic n

10、umber Circuit function INL/DNL (TA= +25C) 01 AD9048T 8-bit video analog-to-digital converter 0.5 LSB 02 AD9048S 8-bit video analog-to-digital converter 0.75 LSB 03 TS83048 8-bit video analog-to-digital converter 0.65 LSB 1.2.3 Device class designator. The device class designator is a single letter i

11、dentifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-

12、PRF-38535 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 28 Dual-in-line, side brazed 3 CQCC1-N28 28 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified

13、in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90927 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVI

14、SION LEVEL G SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ VCCto DGND. -0.5 V dc to +7.0 V dc AGND to DGND -0.5 V dc to +0.5 V dc VEEto AGND. +0.5 V dc to -7.0 V dc VIN, VRTor VRBto AGND . +0.5 V to VEEDifferential reference voltage (VRTto VRB). -2.2 V dc to +2.2 V dc CONV, NMINV or

15、 NLINV to DGND. -0.5 V dc to +5.5 V dc Applied output voltage to DGND . -0.5 V dc to +5.5 V dc 2/ Applied output current, externally forced. -1.0 mA to +6.0 mA 3/,4/ Output short-circuit duration 1.0 s 5/ Junction temperature +175C Thermal resistance, junction-to-case (JC) Case outline X . 15C/W Cas

16、e outline 3 21C/W Lead temperature, (soldering, 10 sec) +300C Storage temperature range . -65C to +150C 1.4 Recommended operating conditions. Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specifi

17、cation, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Spec

18、ification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings.

19、 (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text

20、 of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the

21、device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Applied voltage must be current-limited to specified range. 3/ Forcing voltage must be limited to specified range. 4/ Current is specified as a negative when flowing into the device. 5/ Output High; o

22、ne pin to ground; one second duration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90927 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREM

23、ENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or functi

24、on as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be a

25、s specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on f

26、igure 2. 3.2.3 Block diagram. The block diagrams shall be as specified on figure 3. 3.2.4 Output circuit. The output circuit shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performan

27、ce characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgro

28、up are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking

29、the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark.

30、 The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be req

31、uired from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The ce

32、rtificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendi

33、x A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device cl

34、ass M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity

35、retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microc

36、ircuit group number 57 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90927 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 5 DSCC FORM 2234 AP

37、R 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions Group A Device Limits Unit -55C TA +125C subgroups type VCC= 5.0 V, VEE= -5.2 V unless otherwise specified Min Max Positive supply current +ICC1/, 2/ 1 01, 02 56 mA 2, 3 58 1/, 2/, 3/ 1 03 46 2, 3 48 Negative supply current

38、 -ICC1/, 2/ 1 01, 02 110 mA 2, 3 120 1/, 2/, 4/ 1 03 110 2, 3 120 Analog input bias current IB1/, 3/, 4/, 5/ 1 All 60 A 2, 3 100 Analog input resistance RI 1/, 6/ 1 All 200 k 2, 3 40 Reference ladder RR 1/ 1, 2, 3 01, 02 30 125 resistance 03 125 205 Reference ladder current IRC1/, 7/ 1, 2, 3 All 40

39、mA Invert input logic “0“ IIL1/, 3/, 7/, 8/ 1, 2, 3 01, 02 200 A current 03 400 Invert input logic “1“ IIH1/, 3/, 7/, 9a/, 9b/ 1, 2, 3 01, 02 750 A current 1/, 3/, 7/, 9a/ 1, 2, 3 03 250 /, 3/, 7/, 9b/ 10 Digital output logic “0“ VOL1/, 4/, 10/, 11/ 1, 2, 3 All 0.5 V voltage Digital output logic “1“

40、 VOH1/, 10/, 11/ 1, 2, 3 All 2.4 V Short circuit current 12/ IOS1/, 3/, 7/, 13/ 1, 2, 3 All -175 -30 mA Conversion rate FS1/, 7/, 11/, 14/ 9 01, 02 35 MSPS 03 50 Transient response 1/, 13/, 14/, 15/, 27/ 9 01, 02 20 ns /, 13/, 14/, 15/ 03 20 Convert input logic “0” IIL1/, 3/, 7/, 8/ 1, 2, 3 All 500

41、A current Convert input logic”1” IIH1/, 3/, 7/, 9a/, 9b/ 1, 2, 3 01, 02 150 A current 1/, 3/, 7/, 9a/ 1, 2, 3 03 250 /, 3/, 7/ 9b/ 1, 2 40 3 10 Convert pulse width 14/ tPWL1/ 9 All 18 ns (low) Convert pulse width 14/ tPWH1/ 9 All 10 ns (high) See footnotes at end of table. Provided by IHSNot for Res

42、aleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90927 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Con

43、ditions Group A Device Limits Unit -55C TA +125C subgroups type VCC= 5.0 V, VEE= -5.2 V unless otherwise specified Min Max Signal-to-noise ratio SNR AIN= 1.248 MHz, 15/, 16/, 4 01 45 dB TA= +25C IN= 2.438 MHz, 15/, 16/, 44 TA= +25C IN= 1.248 MHz, 15/, 17/, 54 TA= +25C IN= 2.438 MHz, 15/, 17/, 53 TA=

44、 +25C IN= 1.248 MHz, 15/, 16/, 4 02, 03 43.5 TA= +25C IN= 2.438 MHz, 15/, 16/, 43 TA= +25C IN= 1.248 MHz, 15/, 17/, 52.5 TA= +25C IN= 2.438 MHz, 15/, 17/, 52 TA= +25C IN= 1.248 MHz, 16/, 18/ 4 01 45 TA= +25C 02, 03 43.5 Differential linearity DNL 19/ 4 01 0.5 LSB 5, 6 0.75 4 02 0.75 5, 6 1.0 03 0.65

45、 5, 6 0.75 Integral linearity INL 19/ 4 01 0.5 LSB 5, 0.75 4 02 0.75 5, 6 1.0 03 0.65 5, 0.75 No missing codes QMISS19/ 4, 5, 6 All PASS/FAIL Top of reference ladder EOT19/, 20/ 4, 5, 6 01, 02 12 mV offset 03 20 Bottom of reference ladder EOB19/, 21/ 4, 5, 6 01, 02 8 mV offset 03 10 Convert input lo

46、gic “1“ VIH19/, 22/ 4, 5, 6 All 2.0 V voltage Convert input logic “0“ VIL19/, 22/ 4, 5, 6 All 0.8 V voltage See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90927 DEFENSE SUPPLY

47、CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions Group A Device Limits Unit -55C TA +125C subgroups type VCC= 5.0 V, VEE= -5.2 unless otherwise specified Min Max Output propaga

48、tion delay tPD1/, 3/, 7/, 14/, 23/, 24/ 9 All 15 ns Output rise time tR1/, 14/, 23/, 25/ 9 All 9 ns Output fall time tF1/, 14/, 23/, 25 All 14 ns Output hold time tOH1/, 3/, 4/, 14/, 23/, 24/ 9 01, 02 5 ns 03 4 Output time skew tS1/ 9 All 7 ns In-band harmonics TA= +25C, 1/, 26/ 4 01 49 dBc 02 47 TA= +25C, 1/, 26/, 27/ 03 47 1/ Differential reference voltage = 2.0 V. 2/ Tested worst case with all outputs low, and all digital inputs at logic “0“. 3/ VCC= 5.5 V. 4/ VEE= -5.5 V. 5/ Measured wit