DLA SMD-5962-90954 REV D-2011 MICROCIRCUIT HYBRID LINEAR +5 AND 卤15 VOLT TRIPLE CHANNEL DC DC CONVERTER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Table I; For the output voltage test (VOUT) changed in the conditions block IOUT= 0 (main) to IOUT= 100 mA (main). For the output current test (IOUT) changed the min limit from 0.0 to 100 mA. For the line and load regulation tests (VRLINE) and (V

2、RLOAD) changed in the conditions block from IOUT= 0, 1000, 2000 mA (main) to IOUT= 100, 1000, 2000 mA (main). -sld 99-02-23 K. A. Cottongim B Updated drawing to reflect the current requirements of MIL-PRF-38534. -sld 03-07-31 Raymond Monnin C Correct paragraphs 4.2.a.2 and 4.3.3.b.2. -gz 07-02-05 Jo

3、seph Rodenbeck D Table II, add note to Group C end-point test parameters. Reinstate original paragraphs 4.2.a.2 and 4.3.3.b.2. Update boilerplate paragraphs. -gz 11-03-09 Charles F. Saffle THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV D D D D D D D D

4、D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE

5、 APPROVED BY Gregory Lude MICROCIRCUIT, HYBRID, LINEAR, +5 AND 15 VOLT, TRIPLE CHANNEL, DC/DC CONVERTER DRAWING APPROVAL DATE 92-05-13 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-90954 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E274-11 Provided by IHSNot for ResaleNo reproduction or networki

6、ng permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90954 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF

7、-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 90954 01 H

8、X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified

9、 RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 ATO2815T/CH, ATO2815TF/CH DC/DC converter, 15 W, +5 V and 15 V outpu

10、ts 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The

11、product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability

12、 devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and c

13、onformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should

14、 be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outlines. The case outlin

15、es are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 10 Dual-in-line Z See figure 1 10 Flanged 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. Provided by IHSNot for ResaleNo reproduction or netwo

16、rking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90954 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Input voltage range -0.5 V dc to +50 V dc Power dissipation (PD) . 8 W Lead tem

17、perature (soldering, 10 seconds) +300C Storage temperature range -65C to +150C 1.4 Recommended operating conditions. Input voltage range +16 V dc to +40 V dc Output currents: +5 V output . 2000 mA 15 V output . 167 mA Output power . 15 W 2/ 3/ Case operating temperature range (TC) -55C to +125C 2. A

18、PPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEP

19、ARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 -

20、 List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order

21、 of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Ite

22、m requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as d

23、esignated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect

24、 the form, fit, or function of the device for the applicable device class. 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Derate output power linearly above case tempe

25、rature +125C to 0 at +135C. 3/ At least 20 percent of the total power should be from the main (+5 volt) output. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90954 DLA LAND AND MARITIME COLUMBUS, OHIO 43218

26、-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3

27、.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature r

28、ange. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with

29、the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the init

30、ial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer a

31、nd be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritim

32、e-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 S

33、ampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shal

34、l be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DL

35、A Land and Maritime-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TCas specified in accordance with table I of method 1015 o

36、f MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

37、 from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90954 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC+125C VIN= 28 V dc 5%, CL= 0 unless otherwise specified Group A

38、subgroups Device type Limits Unit Min Max Output voltage 1/ VOUTIOUT= 100 mA (main) 1 01 4.95 5.05 V 2,3 4.90 5.10 IOUT= 0 (dual) 1 14.85 15.15 2,3 14.70 15.30 Output current 1/ 2/ 3/ IOUTVIN= 16, 28, and 40 V dc (main) 1,2,3 01 100 2000 mA VIN= 16, 28, and 40 V dc (dual) 0.0 167 Output ripple volta

39、ge 1/ 4/ VRIPVIN= 16, 28, and 40 V dc, B.W. = dc to 2 MHz (main) 1,2,3 01 80 mVp-p VIN= 16, 28, and 40 V dc, B.W. = dc to 2 MHz (dual) 40 Line regulation 1/ 3/ VRLINEVIN= 16, 28, and 40 V dc, IOUT= 100, 1000, and 2000 mA (main) 1,2,3 01 25 mV VIN= 16, 28, and 40 V dc, IOUT= 0, 84, and 167 mA (dual)

40、1 35 mV 2,3 75 Load regulation 1/ 3/ VRLOADVIN= 16, 28, and 40 V dc, IOUT= 100, 1000, and 2000 mA (main) 1,2,3 01 50 mV VIN= 16, 28, and 40 V dc, IOUT= 0, 84, and 167 mA (dual) 75 Input current IINIOUT= 0, inhibit (pin 8) tied to input return (pin 10) 1,2,3 01 15 mA IOUT= 0, inhibit (pin 2) open 40

41、Input ripple current 4/ IRIPIOUT= 2000 mA (main), IOUT= 167 mA (dual), B.W. = dc to 2 MHz 1,2,3 01 50 mAp-p Efficiency EFFIOUT= 2000 mA (main), IOUT= 167 mA (dual), TC= +25C 1 01 76 % See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

42、from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90954 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC+125C VIN= 28 V dc 5%, CL= 0 unless otherwise specifi

43、ed Group A subgroups Device type Limits Unit Min Max Isolation ISO Input to output or any pin to case (except pin 7) at 500 V dc, TC= +25C 1 01 100 M Power dissipation, load fault 3/ PDOverload, TC= +25C 5/ 1 01 8 W Short circuit, TC= +25C 6 Switching frequency 1/ FSIOUT= 2000 mA (main), IOUT= 167 m

44、A (dual) 4,5,6 01 225 275 kHz Inhibit open circuit voltage VOI1,2,3 01 9 13 V 1/ Tested at each output. 2/ Parameter guaranteed by line and load regulation tests. 3/ At least 20 percent of the total output power should be taken from (+5 volt) main output. 4/ Bandwidth guaranteed by design. Tested fo

45、r 20 kHz to 2 MHz. 5/ An overload is that condition with a load in excess of the rated load but less than that necessary to trigger the overload protection circuit and is the condition of maximum power dissipation. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

46、from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90954 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 Case outline X. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAND

47、ARD MICROCIRCUIT DRAWING SIZE A 5962-90954 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 Case outline Z. Inches mm .005 0.13 .040 1.02 .055 1.40 .162 4.12 .260 6.60 .400 10.16 .500 12.70 1.000 25.40 1.350 34.29 1.950 49.53 2.360 59.94 2.700 68.58 NOTE

48、S: 1. Dimensions are in inches. 2. Metric equivalents are for general information only. 3. Unless otherwise specified, tolerance is .005 inches, (0.13 mm). 4. Case outline X weight: 72 grams maximum. 5. Case outline Z weight: 76 grams maximum. FIGURE 1. Case outlines Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,