DLA SMD-5962-90978 REV A-2009 MICROCIRCUIT HYBRID LINEAR 12-BIT ULTRA HIGH SPEED DIGITAL TO ANALOG CONVERTER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add note to table II, Group C end-point test parameters. -gz 09-04-13 Joseph D. RodenbeckREV SHEET REV SHEET REV STATUS REV A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Steve Duncan DEFENSE SUPPLY CENTER COLU

2、MBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael Jones COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY K. A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, 12-BIT, ULTRA HIGH SPEED, DIGITAL TO ANALOG CONVERTER AND AGENCIES OF THE DEPART

3、MENT OF DEFENSE DRAWING APPROVAL DATE 94-06-24 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-90978 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E273-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-9097

4、8 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are

5、 reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 90978 01 H X X Federal RHA Device Device Case Lead stock class designator type class outli

6、ne finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-)

7、 indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 HDS-1250ATM/883B D/A converter, 12-bit, ultra high speed 1.2.3 Device class designator. This device class designator shall be a single letter

8、 identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation

9、K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class

10、. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upo

11、n one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system per

12、formance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRA

13、WING SIZE A 5962-90978 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 24

14、Dual-in-line 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Positive supply voltage (+VS). +17 V dc Negative supply voltage (-VS) -17 V dc Power dissipation (PD) . 1.09 W Digital input voltage range (VIN) . 0 to +7.0 V Junction temperature

15、 (TJ) +165C Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds) +300C 1.4 Recommended operating conditions. Positive supply voltage range (+VS). +14.5 V dc to +15.5 V dc Negative supply voltage range (-VS) -14.5 V dc to -15.5 V dc Case operating temperature range (TC). -

16、55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation

17、 or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOO

18、KS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-509

19、4.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresse

20、s above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE

21、 A 5962-90978 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MI

22、L-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requi

23、rements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and p

24、hysical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Block diagram. The block diagram shall be as

25、 specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test req

26、uirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer

27、s vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for

28、each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) up

29、on request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PR

30、F-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PR

31、F-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn

32、-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs

33、, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, excep

34、t interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90978 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43

35、218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Conditions 1/ +VS= +15 V, -VS= -15 V unless otherwise specified Group A subgroups Device type Min Max Unit ACCURACY 1 -21 +21 Unipolar offset, (full scale) UPOSBits 1 through 1

36、2 off 2,3 01 -26 +26 A Bits 1 through 12 on, Output = IOUT-1.0 +1.0 Unipolar gain, (full scale) UPGBits 1 through 12 on, VOUTwith internal load (RLOAD) = 200 4 01 -2.0 +2.0 %FS Unipolar gain verses temperature (full scale) UPGTBits 1 through 12 on, Output = IOUT5,6 01 -75 +75 ppm/C Bipolar offset (f

37、ull scale) BPOSBits 1 through 12 off, pins 20 and 22 connected 4 01 -1.0 +1.0 %FS Bipolar offset verses temperature (full scale) BPOSTBits 1 through 12 off, pins 20 and 22 connected 5,6 01 -30 +30 ppm/C Bipolar gain (full scale) BPGBits 1 through 12 on, pins 20 and 22 connected 4 01 -1.0 +1.0 %FS Bi

38、polar zero (full scale) BPZROBit 1 on, bits 2 through 12 off, pins 20 and 22 connected 4 01 -0.2 +0.2 %FS Bipolar zero verses temperature (full scale) BPZROTBit 1 on, bits 2 through 12 off, pins 20 and 22 connected 5,6 01 -75 +75 ppm/C 4 -0.5 +0.5 Integral linearity INL Output = IOUT, Best fit line

39、5,6 01 -1.5 +1.5 LSB 4 -0.5 +0.5 Differential linearity DIL Output = IOUT, All major carries 5,6 01 -1.0 +2.0 LSB DATA INPUTS Input voltage high VIH2/ 1,2,3 01 +2.5 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAN

40、DARD MICROCIRCUIT DRAWING SIZE A 5962-90978 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ +VS= +15 V, -VS= -15 V unless otherwise specified Group A

41、subgroups Device type Min Max Unit DATA INPUTS - Continued. Input voltage low VIL2/ 1,2,3 01 +0.8 V 1,3 40 Input current high IIHBits 1 through 12 on, VIN= 2.5 V and 7.0 V 2 01 100 A Bit 1 = logic “0“, bits 1 through 12 = 0.0 V 7.0 Input current low IILBits 2 through 12 = logic “0“, bits 1 through 1

42、2 = 0.0 V 1,2,3 01 3.5 mA AC CHARACTERISTICS Settling time tSOutput : VOUT, 1 LSB step at midscale to 0.1%, internal load (RLOAD) = 200 9 01 35 ns POWER SUPPLIES Positive supply current +ISBits 1 through 12 off, +VS= +15 V 1,2,3 01 54 mA Negative supply current -ISBits 1 through 12 off, -VS= -15 V 1

43、,2,3 01 -19 mA 1 0.06 +PSRR Bits 1 through 12 on, +VS= +14.5 V and +15.5 V 2.3 0.08 1 0.06 Power supply rejection ratio -PSRR Bits 1 through 12 on, -VS= -14.5 V and -15.5 V 2.3 01 0.08 %/% 1/ Unless otherwise specified, all parameters are tested at TC= -55C, TA= +25C, and TC= +125C. 2/ These paramet

44、ers are guaranteed but not tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90978 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 Millimeters Inc

45、hes Symbol Min Max Min Max A - 5.08 - .200 b 0.36 0.58 .014 .023 D 32.13 32.51 1.265 1.280 e 2.29 2.79 .090 .110 eA 14.99 15.75 .590 .620 E 19.43 19.81 .765 .780 Q 5.08 6.86 .200 .270 S - 2.54 - .100 NOTES: 1. The U.S. Government preferred system of measurement is the metric SI. This item was design

46、ed using inch- pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin 1 is indicated by a contrasting color bead located on the bottom of the package. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo

47、 reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90978 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outline X Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 1

48、0 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Bit 1 (MSB) Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8 Bit 9 Bit 10 Bit 11 Bit 12 (LSB) Ground Ground Ground Ground Ground Ground Ground Output RLOAD(200) Bipolar offset -VS(-15 V) +VS(+15 V) FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90978 DEFENSE SUPPL