DLA SMD-5962-90987 REV A-2010 MICROCIRCUIT LINEAR FREQUENCY CONTROLLER PHASE LOCKED MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update boilerplate paragraphs to current MIL-PRF-38535 requirements. - ro 10-05-04 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 1

2、1 PMIC N/A PREPARED BY DAN WONNELL DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MIC

3、ROCIRCUIT, LINEAR, FREQUENCY CONTROLLER, PHASE LOCKED, MONOLITHIC SILICON DRAWING APPROVAL DATE 92-04-17 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-90987 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E303-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

4、rom IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90987 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) an

5、d space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following exam

6、ple: 5962 - 90987 01 M E A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 spe

7、cified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify

8、 the circuit function as follows: Device type Generic number Circuit function 01 UC1633 Frequency controller, phase locked 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation

9、M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as foll

10、ows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or

11、networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90987 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ Input supply voltage (+VIN) . +20 V dc Reference output curren

12、t -30 mA Operational amplifier output current 30 mA Operational amplifier input voltage range . -0.3 V dc to +20 V dc Phase detector output current 10 mA Lock indicator output current 15 mA Lock indicator output voltage +20 V Divide select input voltage range -0.3 V dc to +10 V dc Double edge disabl

13、e input voltage range -0.3 V dc to +10 V dc Oscillator input voltage range . -0.3 V dc to +5 V dc Sense amplifier input voltage range -0.3 V dc to +20 V dc Power dissipation (PD) at TA= +25C 1000 mW 3/ Operating junction temperature range (TJ) . -55C to +150C Storage temperature range . -65C to +150

14、C Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) 100C/W 1.4 Recommended operating conditions. Input supply voltage (+VIN) . 12.0 V Ambient operating temperature range (TA) . -55C to +125C 2. APP

15、LICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPAR

16、TMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HD

17、BK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) _

18、 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Voltages are referenced to ground, pin 16. Currents are positive into, negative out of, the specified terminals. 3/ Der

19、ate above TA= +25C at 10 mW/C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90987 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of preced

20、ence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirem

21、ents. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein

22、. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF

23、-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance c

24、haracteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The

25、 electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the

26、 entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Markin

27、g for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535,

28、 appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from

29、 a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V

30、, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shal

31、l be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.

32、9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Mic

33、rocircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 110 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZ

34、E A 5962-90987 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA+125C Group A subgroups Device type Limits Unit +VIN= 12 V unless otherwise specified Min Max Supply v

35、oltage ICC+VIN= 15 V 1,2,3 01 28 mA Reference section Output voltage VREF1,2,3 01 4.75 5.25 V Load regulation VRLOADIOUT= 0 mA to 7 mA 1,2,3 01 20 mV Line regulation VRLINE+VIN= 8 V to 15 V 1,2,3 01 20 mV Short circuit current IOSVOUT= 0 V 1,2,3 01 12 mA Oscillator section DC voltage gain AVOscillat

36、or input to oscillator output 4,5,6 01 12 20 dB Input DC level VIBOscillator input pin open 1,2,3 01 1.15 1.45 V Input impedance RI+VIN= VIB0.5 V 1,2,3 01 1.3 1.9 k Output dc level VOBOscillator input pin open 1,2,3 01 1.2 1.6 V Maximum input frequency fMAX4,5,6 01 10 MHz Dividers: Maximum input fre

37、quency fINInput = 1 V VPPat oscillator input 4,5,6 01 10 MHz Divide 4/5 input current IINInput = 5 V, (divide by 4) 1,2,3 01 500 A Input = 0 V, (divide by 5) -5.0 5.0 Divide 4/5 threshold voltage VTH1,2,3 01 0.5 2.2 V Divide 2/4/8 input current IINInput = 5 V, (divide by 8) 1,2,3 01 500 A Input = 0

38、V, (divide by 2) -500 Divide 2/4/8 open circuit voltage V(OPEN)Input current = 0 A, (divide by 4) 1,2,3 01 1.5 3.5 V Divide by 2 threshold VTH1,2,3 01 0.20 V Divide by 4 threshold VTH1,2,3 01 1.5 3.5Divide by 8 threshold VTHVolts below VREF1,2,3 01 0.20 V Provided by IHSNot for ResaleNo reproduction

39、 or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90987 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA+125C

40、 Group A subgroups Device type Limits Unit +VIN= 12 V unless otherwise specified Min Max Sense amplifier Threshold voltage VTHPercent of VREF1,2,3 01 27 33 % Input bias current IINInput = 1.5 V 1,2,3 01 -1.0 A Double edge disable input: Input current IINInput = 5 V (disabled) 1,2,3 01 500 A Input =

41、0 V (enabled) -5.0 5.0 Threshold voltage VTH1,2,3 01 0.5 2.2 V Phase detector: High output level VOUT(H)Positive phase/frequency error, volts below VREF1,2,3 01 0.5 V Low output level VOUT(L)Negative phase/frequency error 1,2,3 01 0.5 V Mid output level VOUT(M)Zero phase/frequency error, Percent of

42、VREF1,2,3 01 47 53 % High level maximum source current ISOURCEVOUT= 4.3 V 1,2,3 01 2.0 mA Low level maximum sink current ISINKVOUT= 0.7 V 1,2,3 01 2.0 mA Mid level output impedance ROIOUT= -200 A to +200 A 1,2,3 01 4.5 7.5 k Lock indicator output: Saturation voltage VSATFrequency error, IOUT= 5 mA 1

43、,2,3 01 0.45 V Leakage current ILKZero frequency error, VOUT= 15 V 1,2,3 01 1.0 A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90987 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL

44、A SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA+125C Group A subgroups Device type Limits Unit +VIN= 12 V unless otherwise specified Min Max Loop amplifier: Non-inverting reference voltage VREFPercent of VREF1,2,3 01 47 53 % I

45、nput bias current IINInput = 2.5 V 1,2,3 01 -0.8 A Large signal voltage gain AVOL4,5,6 01 60 dB Power supply rejection ratio PSRR +VIN= 8 V to 15 V 4,5,6 01 70 dB Short circuit current IOSSource: VOUT= 0 V 1,2,3 01 16 mA Sink: VOUT= 5 V 16 Auxiliary operational amplifier: Input offset voltage VIN(of

46、fset) VCM= 2.5 V 1,2,3 01 8 mV Input bias current IIN(bias) VCM= 2.5 V 1,2,3 01 -0.8 A Input offset current IIN(offset) VCM= 2.5 V 1,2,3 01 0.1 A Large signal voltage gain AVOL4,5,6 01 70 dB Power supply rejection ratio PSRR +VIN= 8 V to 15 V 4,5,6 01 70 dB Common mode rejection ratio CMRR VCM= 0 V

47、to 10 V 4,5,6 01 70 dB Short circuit current IOSSource: VOUT= 0 V 1,2,3 01 16 mA Sink: VOUT= 5 V 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90987 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-39

48、90 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outline E Terminal number Terminal symbol 1 DIVIDE 4/5 INPUT 2 DIVIDE 2/4/8 INPUT 3 LOCK INDICATOR OUTPUT 4 PHASE DETECTOR OUTPUT 5 DOUBLE EDGE DISABLE INPUT 6 SENSE AMPLIFIER INPUT 7 5 V REFERENCE OUTPUT 8 LOOP AMPLIFIER INVERSE INPUT 9 LOOP AMPLIFIER OUTPUT 10 AUXILIARY AMPLIFIER INVERSE INPUT 11 AUXILIARY AMPLIFIER NONINVERSE INPUT 12 AUXILIARY AMPLIFIER OUTPUT 13 +VIN14 OSCILLATOR OUTPUT 15 OSCILLATOR INPUT16 GROUND FIGURE 1