DLA SMD-5962-91536 REV B-2012 MICROCIRCUIT DIGITAL ECL TRIPLE D FLIP-FLOP MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Radiation requirements added. Update to reflect latest changes in format and requirements. Editorial changes throughout. -les 04-01-29 Raymond Monnin B Update drawing as part of 5 year review. jt. 12-10-11 C. SAFFLE REV SHEET REV B SHEET 15 REV S

2、TATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Thanh V. Nguyen DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIE

3、S OF THE DEPARTMENT OF DEFENSE CHECKED BY Thanh V. Nguyen APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, ECL, TRIPLE D FLIP-FLOP MONOLITHIC SILICON DRAWING APPROVAL DATE 93-01-26 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-91536 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E469-12 Provi

4、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91536 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance

5、 class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is

6、reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 91536 01 M X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA desig

7、nator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) in

8、dicates a non-RHA device. 1.2.2 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 100331 Triple D flip-flop 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as fol

9、lows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outlines. The case outli

10、nes are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X GDIP5-T24 or CDIP6-T24 24 dual-in-line Y See figure 1 24 quad-flat 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, ap

11、pendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91536 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings.

12、1/ Supply voltage range (VEE) -7.0 V dc to +0.5 V dc Dc input voltage range (VIN). VEEto +0.5 V dc Dc input current range (IIN) . -30 mA to +5.0 mA Storage temperature range . -65C to +150C Maximum dc output current (IOUT) . -50 mA Maximum power dissipation (PD) 2/ . 805 mW Lead temperature (solderi

13、ng, 10 seconds) . +300C Junction temperature (TJ) +175C Thermal resistance, junction-to-case (JC): Case X . See MIL-STD-1835 Case Y . 28C/W 1.4 Recommended operating conditions. Negative supply voltage range (VEE) . -5.7 V dc minimim to 4.2 V dc maximum High level input voltage range (VIH) -1.165 V

14、dc minimum to 0.870 V dc maximum Low level output voltage (VIL) . -1.830 V dc minimum to 1.475 V dc maximum Ambient operating temperature range (TA) . -55C to +125C Minimum setup time, Dnto CPC/CPn(ts) TC= +25C . 0.8 ns TC= +125C . 0.9 ns TC= -55C 1.0 ns Minimum hold time, Dnto CPC/CPn(th) TC= +25C

15、. 1.3 ns TC= +125C . 1.6 ns TC= -55C 1.5 ns Minimum setup time, CDn/SDnto CPC/CPn(ts) TC= +25C . 1.3 ns TC= +125C . 1.6 ns TC= -55C 1.5 ns Minimum setup time, MR/MS to CPC/CPn(ts) TC= +25C . 2.3 ns TC= +125C . 2.5 ns TC= -55C 2.5 ns Minimum pulse width, high, CPC/CPn/CDn/SDn/MS/MR (tW(H) 2.0 ns Maxi

16、mum toggle frequency (fMAX) . 400 MHz 1.5 Radiation features. Maximum total dose available (dose rate = 50 300 rads(Si)/s) 300Krads(Si) _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affec

17、t reliability. 2/ Maximum power dissipation is defined as VCCX ICC, and must withstand the added PDdue to short circuit test e.g., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91536 DLA LAND AND MARIT

18、IME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, t

19、he issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface

20、Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Documen

21、t Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws

22、and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) plan. Th

23、e modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical d

24、imensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Te

25、rminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table. The truth table shall be as specified on figure 3. 3.2.4 Test circuit and switching waveforms. The test circuit and switching waveforms shall be as specified on figure 4. Provided by IHSNot for ResaleN

26、o reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91536 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless o

27、therwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified i

28、n table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations,

29、 the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535,

30、appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q

31、 and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of s

32、upply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein

33、or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits de

34、livered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for

35、 device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.1

36、0 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 31 see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING

37、SIZE A 5962-91536 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC +125C 1/ unless otherwise specified Group A subgroups Device type Limits Unit Min Max High level output vol

38、tage VOHVIL= -1.83 V, 1, 2 All -1.025 -0.870 V VIH= -0.87 V, 3 -1.085 -0.870 Low level output voltage VOLVEE= -5.7 V, -4.2 V, 1, 2 All -1.830 -1.620 V Loading: 50 to 2.0V 3 -1.830 -1.555 High level threshold VOHCVIL= -1.475 V, 1, 2 All -1.035 V output voltage VIH= -1.165 V, 3 -1.085 Low level thresh

39、old VOLCVEE= -5.7 V, -4.2 V, 1, 2 All -1.610 V output voltage Loading: 50 to 2.0V 3 -1.555 High level input current IIHVEE= -5.7 V, 1, 2 All 240 A VIN= -0.87 V 3 340 Low level input current IILVEE= -4.2 V, 1, 2, 3 All 0.5 A VIN= -1.83 V Negative power supply IIHVEE= -5.7 V, -4.2 V 1, 2, 3 All -130 -

40、50 mA drain current Functional tests VEE= -5.7 V, -4.2 V, VIH= -1.023 V, VIL= -1.642 V, See 4.4.1b, 7, 8 All Propagation delay time, tPLH19 All 0.6 2.0 ns common clock to output, tPHL1See figure 4 10 0.5 2.4 CPCto Qn, Qn 11 0.5 2.2 Propagation delay time, tPLH29 All 0.6 2.0 ns individual clock to ou

41、tput, tPHL210 0.5 2.4 CPnto Qn, Qn 11 0.5 2.2 Propagation delay time, tPLH3CPC, CPn= low 9 All 0.6 2.0 ns individual direct clear/ tPHL310 0.5 2.4 individual direct set to 11 0.5 2.2 output, CDn/SDnto Qn, Qn CPC, CPn= high 9 All 0.6 2.1 ns 10 0.5 2.5 11 0.5 2.4 See footnotes at end of table. Provide

42、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91536 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test

43、Symbol Conditions -55C TC +125C 1/ unless otherwise specified Group A subgroups Device type Limits Unit Min Max Propagation delay time, tPLH4See figure 4 CPC, CPn= low 9 All 0.8 2.6 ns master set/master reset tPHL410 0.8 2.9 to output, MS/MR to Qn, 11 0.7 2.7 QnCPC, CPn= high 9 All 0.8 2.8 ns 10 0.8

44、 3.1 11 0.7 2.9 Transition time, tTLH9, 10, 11 All 0.2 1.4 ns output, Qn, Qn2/ tTHL1/ Pre and Post-irradiation values are identical unless otherwise specified in table I. When performing post irradiation electrical measurements for any RHA level, TA= +25C. 2/ This parameter is provided as design inf

45、ormation only (not tested but guaranteed). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91536 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Case Y Dimension

46、 Millimeters Inches Notes Min Max Min Max A 2.16 .085 b 0.41 0.46 .015 .019 c 0.10 0.15 .004 .007 D 22.10 28.45 .870 1.120 D1 9.40 10.16 .370 .400 4 E 22.10 28.45 .870 1.120 E1 9.40 10.16 .370 .400 4 e 1.14 1.40 .045 .055 L 6.35 9.14 .250 .360 Q 0.89 1.27 .035 .050 5 S 1.91 .075 NOTES: 1. The prefer

47、red unit of measurement is millimeters. However, this item was designed using inch-pound units of measurement. In case problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Lead number 1 is identified by a tab located on the lead. 3. Lead numbers a

48、re shown for reference only and do not appear on the package. 4. Dimensions D1 and E1 allow glass meniscus. 5. Dimension Q shall be measured at the point of exit of the lead from the body. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91536 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 De