DLA SMD-5962-91632 REV C-2008 MICROCIRCUIT LINEAR QUAD PRECISION OPERATIONAL AMPLIFIER MONOLITHIC SILICON《微电路 线性高精度单片四运算放大器》.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device types 03 and 04. Changes to TABLE I. 93-07-06 M. A. FRYE B Add case outline X. Inactivate case outline G. Make changes to 1.2.4, FIGURE 1, and FIGURE 2. 95-06-30 M. A. FRYE C Replaced reference to MIL-STD-973 with reference to MIL-PRF-

2、38535. - ro 08-03-19 R. HEBER REV SHET REV SHET REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK C. OFFICER DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY CHARLES E. BESORE COLUMBUS, OHIO 43218-3990 http:/w

3、ww.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHAEL A. FRYE AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 93-01-21 MICROCIRCUIT, LINEAR, QUAD, PRECISION OPERATIONAL AMPLIFIER, MONOLITHIC SILICON AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5

4、962-91632 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E186-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91632 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 223

5、4 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN).

6、When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 91632 01 M C A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4)

7、 Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA l

8、evels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: VOS(TA= +25C) Device type Generic number Circuit function _(single supply)_ 01 LT1079 Quad, precision operational amplif

9、ier 150 V 02 LT1079A Quad, precision operational amplifier 100 V 03 LT1078 Dual, precision operational amplifier 120 V 04 LT1078A Dual, precision operational amplifier 70 V 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follow

10、s: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outlin

11、e(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line G MACY1-X8 8 Can P GDIP1-T8 or CDIP2-T8 8 Dual-in-line X See figure 1 8 Can 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-3853

12、5 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91632 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SH

13、EET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) . 22 V dc Differential input voltage 30 V dc Input voltage . 2/ Output short circuit duration Indefinite Power dissipation (PD) 266 mW Storage temperature range . -65C to +150C Junction temperature (TJ) . +150C Lead tem

14、perature (soldering, 10 seconds) +300 Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) 100C/W 1.4 Recommended operating conditions. Supply voltage: Single supply operation: +VS+5.0 V dc -VS. 0.0 V dc Dual supply operation: +VS+15 V dc -VS. -15

15、 V dc Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of t

16、hese documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Elect

17、ronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Stan

18、dardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersed

19、es applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Input voltage is equal to the positi

20、ve supply voltage or 5.0 V dc less than the negative supply voltage. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91632 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSC

21、C FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not a

22、ffect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and

23、physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connecti

24、ons shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient

25、 operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manu

26、facturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for devic

27、e classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance m

28、ark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For

29、 device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affi

30、rm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MI

31、L-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to th

32、is drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shal

33、l be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 73 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permit

34、ted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91632 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Gr

35、oup A subgroups Device type Limits 1/ Unit Min MaxSingle supply operation 2/ Input offset voltage VOS1 01 150 V 2,3 400 1 02 100 2,3 280 1 03 120 2,3 370 1 04 70 2,3 250 Input offset current IOS1 01,03 0.35 nA 2,3 0.70 1 02,04 0.25 2,3 0.50 Input bias current IB1 01,03 10 nA 2,3 12 1 02,04 8 2,3 10

36、RINTA= +25C 4 01,03 300 M Differential input 3/ resistance 02,04 400 CMRR VCM= 0 V to 3.5 V 1 01,03 94 dB Common mode rejection ratio VCM= 0.05 V to 3.2 V 2,3 88 VCM= 0 V to 3.5 V 1 02,04 97 VCM= 0.05 V to 3.2 V 2,3 92 PSRR VS= 2.3 V to 12 V 1 01,03 100 dB Power supply rejection ratio VS= 3.1 V to 1

37、2 V 2,3 94 VS= 2.3 V to 12 V 1 02,04 102 VS= 3.1 V to 12 V 2,3 98 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91632 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990

38、REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min MaxSingle supply operation - continued 2/ AVOLVO= 0.03 V to 4.0 V, 1 01,03 150 V/

39、mV Large signal voltage gain no load 02,04 200 VO= 0.03 V to 3.5 V, 1 01,03 120 RL= 50 k 02,04 150 VO= 0.05 V to 4.0 V, 2,3 01,03 80 no load 02,04 110 VO= 0.05 V to 3.5 V, 2,3 01,03 60 RL= 50 k 02,04 80 Output voltage swing -VOUTOutput low, no load 4 All 6.0 mV 5,6 8.0 Output low, TA= +25C, 2.0 k to

40、 ground 4 1.0 Output low, ISINK= 100 A 4 130 5,6 170 +VOUTOutput high, no load 4 4.2 5,6 3.9 Output high, 4 3.5 2.0 k to ground 5,6 3.0 Slew rate 3/ SR AV= +1.0, VS= 2.5 V, TA= +25C 4 All 0.04 V/s Supply current ISPer amplifier 1 01,03 55 A 2,3 70 1 02,04 50 2,3 60 Minimum supply voltage 3/ VMINTA=

41、+25C 1 All 3.5 to 0 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91632 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR

42、97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min MaxDual supply operation 4/ Input offset voltage VOS1 01,03 350 V 2,3 600 1 02,04 250 2,3 430 Input offset current IOS1 01,03

43、 0.35 nA 2,3 0.70 1 02,04 0.25 2,3 0.50 Input bias current IB1 01,03 10 nA 2,3 12 1 02,04 8 2,3 10 Input voltage range VINTA= +25C 1 All +13.5 to -15.0 V CMRR VCM= +13.5 V, -15 V 1 01,03 97 dB Common mode rejection ratio 02,04 100 VCM= +13 V, -14.9 V 2,3 01,03 90 02,04 94 PSRR +VS= +5.0 V to +18 V 1

44、 01,03 100 dB Power supply rejection ratio -VS= 0.0 V to -18 V 2,3 94 1 02,04 102 2,3 98 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91632 DEFENSE SUPPLY CENTER COLUMBUS COL

45、UMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Dual supply operation - continued 4/ AVOLVO= 10 V, RL= 50

46、 k 1 All 1000 V/mV Large signal voltage gain VO= 10 V, RL= 2.0 k 1 01,03 300 02,04 400 VO= 10 V, RL= 5.0 k 2,3 01,03 150 02,04 200 Output voltage swing VOUTRL= 50 k 4 All 13 V RL= 2.0 k 4 11 RL= 5.0 k 5,6 11 Supply current ISPer amplifier 1 01,03 75 A 2,3 95 1 02,04 65 2,3 80 Slew rate 3/ SR AV= +1.

47、0, TA= +25C, VOUT= -5.0 V to +5.0 V, measured at -2.0 V to +2.0 V 4 All 0.06 V/s 1/ The limiting terms “min” (minimum) and “max” (maximum) shall be considered to apply to magnitudes only. Negative current shall be defined as conventional current flow out of a device terminal. 2/ Unless otherwise spe

48、cified, +VS= +5.0 V, -VS= 0.0 V, VCM= 0.1 V, and VOUT= 1.4 V. 3/ If not tested, shall be guaranteed to the limits specified in table I herein. 4/ Unless otherwise specified, +VS= +15 V and -VS= -15 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91632 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2