DLA SMD-5962-91639 REV C-2005 MICROCIRCUIT LINEAR CMOS QUAD DIFFERENTIAL LINE DRIVER MONOLITHIC SILICON《硅单块 互补金属氧化物半导体四列差异总线驱动器 直线式微型电路》.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add vendor CAGE 01295. Make change to VINand PDas specified under paragraph 1.3. Make change to VOH, ICC, IOZ, ISC, skew, tPHZ, and tPLZtests as specified in table I. Changes in accordance with N.O.R. 5962-R109-95. 95-04-14 M. A. Frye B Add case

2、X which is a 16 lead flat pack. Make changes to 1.2.4, 1.3, 1.4, 3.2.1, and figure 1. Redrawn. ro 98-02-20 Raymond Monnin C Update drawing to current requirements. Editorial changes throughout. - drw 05-01-24 Raymond Monnin THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHE

3、T REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Rick C. Officer DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Charles E. Besore COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR

4、USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, CMOS QUAD DIFFERENTIAL LINE DRIVER, MONOLITHIC AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-09-16 SILICON AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-91639 SHEET 1 OF 14 DSCC FORM 2233 APR 97 596

5、2-E110-05 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91639 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documen

6、ts two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness As

7、surance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 91639 01 M E A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing

8、 number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA de

9、signator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identifies the circuit function as follows: Device type Generic number Circuit function 01 26C31 CMOS quad differential line driver 1.2.3 Device class designator. The device class designator is a single letter identi

10、fying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-3

11、8535 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F GDFP2-F16 or CDFP3-F16 16 Flat pack X See figure 1 16 Flat pack 2 CQCC1-N20 20 Square leadless chip c

12、arrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91639 DEF

13、ENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC). -0.5 V dc to 7.0 V dc DC input voltage range (VIN). -0.5 V dc to VCC+0.5 V dc DC output voltage range (VOUT) -0.5 V dc to 7.0 V dc DC outp

14、ut current, per pin (IOUT). 150 mA Input, output clamp diode current (IIK, IOK) 20 mA DC VCCor GND current, per pin (ICC) 150 mA Storage temperature range. -65C to +150C Lead temperature (soldering, 4 seconds) . 260C Junction temperature (TJ) . 150C Thermal resistance, junction-to-case (JC): Cases E

15、, F, 2 See MIL-STD-1835 Case X 11C/W Thermal resistance, junction-to-ambient (JA): Case E +100C/W Case F +150C/W Case X +116C/W Case 2. +85C/W Power dissipation (PD): (TA= +25C) Case E 1375 mW Case F 1000 mW Case X 1293 mW Case 2. 1375 mW 1.4 Recommended operating conditions. Supply voltage range (V

16、CC) 4.5 V dc to 5.5 V dc DC input or output voltage range (VIN, VOUT) 0 V dc to VCCAmbient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing

17、to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 -

18、Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/ass

19、ist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of

20、 this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade

21、performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91639 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENT

22、S 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function

23、as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as s

24、pecified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figu

25、re 2. 3.2.3 Truth table. The truth table shall be as specified on figure 3. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance charact

26、eristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are def

27、ined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-

28、“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certi

29、fication mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from

30、 a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate

31、of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and he

32、rein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For

33、 device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the

34、 option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit gro

35、up number 77 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91639 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE

36、 I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C -4.5 V VCC 5.5 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max Logical 1 input voltage VIH1,2,3 01 2.0 V Logical 0 input voltage VIL1,2,3 01 0.8 V Logical 1 output voltage VOHVIN= VIHor VI

37、L, ICC= 4.5 V, IOUT= -20 mA 1 01 2.4 V 2,3 2.2 Logical 0 output voltage VOLVIN= VIHor VIL, VCC= 4.5 V, IOUT= 20 mA 1,2,3 01 0.5 V Differential output voltage VTVCC= 4.5 V, RL= 100 1/ 1,2,3 01 2.0 V Difference in differential output |VT| -|VT| VCC= 4.5 V, RL= 100 1/ 1,2,3 01 0.4 V Common mode output

38、voltage VOSVCC= 5.5 V, RL= 100 1/ 1,2,3 01 3.0 V Difference in common mode output |VOS-VOS| VCC= 5.5 V, RL= 100 1/ 1,2,3 01 0.4 V Input current IINVIN= VCC, GND, VIH, or VIL, VCC= 5.5 V 1,2,3 01 -1.0 +1.0 A Quiescent power supply current ICCIOUT= 0 A, VCC= 4.5 V, VIN= 5 V or GND 2/ 1,2,3 01 500 A IO

39、UT= 0 A, VCC= 5.5 V, VIN= 2.4 V or 0.5 V 2/ 1 3.0 mA 2,3 3.2 TRI-STATE output leakage current IOZVOUT= 2.5 V or 0.5 V, ENABLE = VIL, VCC= 5.5 V, ENABLE = VIH1,2,3 01 -20 +20 A Output short circuit current ISCVIN= VCCor GND, VCC= 5.5 V 1/, 3/ 1 01 -150 -30 mA 2,3 -170 -30 Output leakage current “powe

40、r off” IOFFVCC= 0 V, VOUT= 6 V 1,2,3 01 100 A VCC= 0 V, VOUT= 0 V -100 Functional tests to output See 4.4.1b 7,8 01 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91639 DEFENSE

41、 SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions -55C TA +125C -4.5 V VCC 5.5 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max Propagation

42、 delay input to output tPLHS1 open 4/ 9,10,11 01 14 ns tPHL14 Skew S1 open 4/ 5/ 9,10,11 01 4 ns Output rise time tTLHS1 open 4/ 9,10,11 01 14 ns Output fall time tTHLS1 open 4/ 9,10,11 01 14 ns Output enable time tPZHS1 closed 4/ 9,10,11 01 22 ns tPZL28 Output disable time tPHZS1 closed 4/ 6/ 9,10,

43、11 01 16 ns tPLZ16 1/ See EIA specification RS-422 for exact test conditions. 2/ Measure per input. All other inputs at 5 V or GND. 3/ This is a current forced when a high output is shorted to GND. Only one output shall be shorted at a time. 4/ See figures 5 and 6. Rise time (tr) 6 ns and fall time

44、(tf) 6 ns. VCC= 5.0 V. 5/ Skew is defined as the difference in propagation delay between complementary output at 50 % point. 6/ Output disable time is the delay from ENABLE or ENABLE being switched to the output transistor turning off. Provided by IHSNot for ResaleNo reproduction or networking permi

45、tted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91639 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Ltr Inches Millimeters Notes Min Max Min Max A .050 .080 1.27 2.03 A1 .004 .012 0.10 0.30 b .015 .019 0.38 0.48 2

46、C .004 .008 0.10 0.20 2 D - .390 - 9.91 E .400 .420 10.16 10.67 E1 .245 .270 6.22 6.86 e .050 BSC 1.27 BSC K .008 .012 0.20 0.30 L .037 .043 0.94 1.09 R .013 .017 0.33 0.43 R1 .013 .017 0.33 0.43 S - .018 - 0.46 S1 .005 - 0.13 - NOTES: 1. The U.S. government preferred system of measurement is the me

47、tric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. 2. Maximum limits may be increased by .003 inches after lead finish is applied. FIGURE

48、 1. Case outline X. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91639 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outlines E, F, and X 2 Terminal number Terminal symbol 1 INPUT A NC 2 CHANNEL A2 OUTPUT INPUT A 3 CHANNEL A1 OUTPUT CHANNEL A2 OUTPUT 4 ENABLE CHANNEL A1 OUTPUT 5 CHANNEL B1 OUTPUT ENABLE 6 CHANNEL B2 OUTPUT NC 7 INPUT B CHANNEL B1 OUTPUT 8 GND C