DLA SMD-5962-92031 REV D-2013 MICROCIRCUIT LINEAR RESONANT-MODE POWER SUPPLY CONTROLLERS MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02. Make changes to 1.2.2, Table I, and figure 1. 94-01-06 M. A. FRYE B Add device type 03. Add case outline 2. Changes to ICC, VRLINE2, VRLOAD2, IIB, VOL, VOH, AVOL, CMRR, and VSATLin table I. Update boilerplate. - rrp 01-02-22 R

2、. MONNIN C Drawing updated to reflect current requirements. - ro 05-12-21 R. MONNIN D Drawing updated to reflect current MIL-PRF-38535 requirements. - ro 13-08-07 C. SAFFLE REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK C. O

3、FFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, RESONAN

4、T-MODE POWER SUPPLY CONTROLLERS, MONOLITHIC SILICON DRAWING APPROVAL DATE 93-03-30 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-92031 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E341-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD M

5、ICROCIRCUIT DRAWING SIZE A 5962-92031 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class Q and M) and space application (device class

6、 V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92031 01 M E A Federa

7、l stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are mark

8、ed with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follo

9、ws: Device type Generic number Circuit function 01 UC1864 Resonant-mode power supply controller 02 UC1865 Resonant-mode power supply controller 03 UC1863 Resonant-mode power supply controller 1.2.3 Device class designator. The device class designator is a single letter identifying the product assura

10、nce level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(

11、s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device

12、classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92031 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 A

13、PR 97 1.3 Absolute maximum ratings. 1/ 2/ Supply voltage (VCC) . 22 V dc Output current (OUTPUT A and OUTPUT B): Source and sink . 0.5 A Pulse 1.5 A Power ground voltage 0.2 V Inputs (+INPUT, -INPUT, ZERO, FAULT) . -0.4 V to 7 V Error amp output current . 2 mA Power dissipation (PD) at 70C 1 W 3/ Ju

14、nction temperature (TJ) +150C Lead temperature (soldering, 10 seconds) +300C Storage temperature range -65C to +150C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case E . 85C/W Case 2 80C/W 1.4 Recommended operating conditions. Supply vol

15、tage (VCC) . 12 V dc Ambient operating temperature (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the is

16、sues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Stand

17、ard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk,

18、700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulation

19、s unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ All voltages are with respect to signal ground and all currents are p

20、ositive into the specified terminal. 3/ Derate at 12.5 mW at TA 70C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92031 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 22

21、34 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the fo

22、rm, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dim

23、ensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified

24、 on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature ra

25、nge. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be

26、 marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall b

27、e in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M sh

28、all be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certif

29、icate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that

30、the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38

31、535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acqui

32、red to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required

33、 documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 58 (see MIL-PRF-38535, appendix A). Provided by IHSNot for

34、 ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92031 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C T

35、A +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max ICCstart ICCVCC= VCC(ON) 0.3 V 1,2,3 All 300 A ICCrun ICCVID= 100 mV 1,2,3 All 32 mA 5 V Generator section Output voltage VOUT12 V VCC 20 V, -10 mA IOUT 0 mA 1,2,3 All 4.8 5.2 V Short circuit current IOSVOUT= 0 V

36、 1,2,3 All -150 -15 mA Soft reference section Reference voltage VREFIOUT= 0 mA, TA= +25C 1 All 4.95 5.05 V 12 V VCC 20 V, -200 A IOUT 200 A 1,2,3 4.85 5.15 Line regulation VRLINE2VCC= 12 V and 20 V 1,2,3 All -20 20 mV Load regulation VRLOAD2IOUT= 200 A 1,2,3 All -30 30 mV Soft start current ISSV = 2

37、 V 1,2,3 All -650 -350 A Restart delay current IRDV = 2 V 1,2,3 All 10 35 A Error amplifier section (VID= V+INPUT V-INPUT) Input offset voltage VIOVCM= 5 V, VOUT= 2 V, IOUT= 0 mA 1,2,3 All -10 10 mV Input bias current IIBVCM= 0 V 1,2,3 All -2 A Output voltage, low VOLVID= -100 mV, IOUT= 200 A 1,2,3

38、All 0.25 V Output voltage, high VOHVID= 100 mV, IOUT= -200 A 1,2,3 All 3.9 V Voltage gain AVOLVCM= 5 V, IOUT= 0 mA, VOUT= 0.5 V and 3.7 V 1,2,3 All 70 dB Power supply rejection ratio PSRR VCM= 5 V, VOUT= 2 V, VCC= 12 V and 20 V 1,2,3 All 70 dB See footnotes at end of table. Provided by IHSNot for Re

39、saleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92031 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/

40、 -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Error amplifier section Continued. (VID= V+INPUT V-INPUT) Common mode rejection ratio CMRR VOUT= 2 V, VCM= 0 V and 6 V 4,5,6 All 65 dB Unity gain bandwidth UGBW 3/ 4,5,6 All 0.5 MHz Voltage controlled osci

41、llator (VCO) section Maximum frequency fMAXVID(error amp) = 100 mV 4 All 450 550 kHz 5,6 425 575 Minimum frequency fMINVID(error amp) = -100 mV 4 All 45 55 kHz 5,6 42 58 One shot section Zero comparator threshold VTHZ1,2,3 All 0.45 0.55 V Maximum pulse width, OUTPUT A tMAXVZERO= 1 V 9,10,11 All 850

42、1150 ns Ratio of maximum to minimum pulse width tMIN/ tMAXVZERO= 0 V 9,10,11 01, 03 2.5 5.5 % 9,11 02 4 7 10 3.8 7 Propagation delay tPD3/ 9,10,11 All 200 ns Output stage section Output low saturation (outputs A and B) VSATLIOUT= 20 mA 1,2,3 All 0.5 V IOUT= 200 mA 2.2 Output high saturation (outputs

43、 A and B) VSATHIOUT= -200 mA, down from VCC1,2,3 All 2.5 V Under-voltage lockout (UVLO), low saturation (outputs A and B) VSL A,BIOUT= 20 mA 1,2,3 All 1.5 V Rise and fall time tR, tFCL= 1 nF 3/ 9,10,11 All 45 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networkin

44、g permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92031 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise

45、specified Group A subgroups Device type Limits 2/ Unit Min Max Fault comparator section Fault comparator threshold voltage VTHF1,2,3 All 2.85 3.15 V Delay to output tDO3/ 4/ 1,2,3 All 200 ns Under-voltage lockout (UVLO) section VCCstart threshold VSTT1,2,3 01, 03 7 9 V 02 15 18 VCCstop threshold VSP

46、T1,2,3 01, 03 6 8 V 02 9.5 11.5 1/ Unless otherwise specified, VCC= 12 V, voltage controlled oscillator capacitance CVCO= 1 nF, range resistance = 7.15 k, RMINresistance = 86.6 k, capacitance = 200 pF, resistance = 4.02 k, and soft ref capacitance = 0.1 F. 2/ The algebraic convention, whereby the mo

47、st negative value is a minimum and the most positive value is a maximum, is used in this table. Negative current shall be defined as conventional current flow out of a device terminal. 3/ If not tested, shall be guaranteed to the limits specified under table I herein. 4/ VIN= 0 V to 4 V, tR(VIN) 10

48、ns, and tPD= t(VOUT= 6 V) t(VIN= 3 V). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92031 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 Device types 01, 02 and 03 01 and 03 Case outlines E 2 Terminal number Terminal symbol 1 5 V SOFT REF 2 +INPUT 5 V 3 -INPUT +INPUT 4 E/A OUT -INPUT 5 SIG GND E/A OUT 6 RANGE SIG GND 7 RMINRANGE 8 CVCORMIN9 RC CVCO10 ZERO R