DLA SMD-5962-92148 REV E-2009 MICROCIRCUIT DIGITAL ADVANCED BIPOLAR CMOS OCTAL TRANSCEIVER WITH THREESTATE OUTPUTS TTL COMPATIBLE INPUTS MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02. Add ground bounce limits. Change input high and low current. Change quiescent supply current, delta. Change input and input/output capacitance. Change propagation delay times for device type 01 - jak. 95-04-05 Monica L. Poelki

2、ng B Change IIH, IIL, ICC, VOLP, VOLV, VOHP, and VOHVfor device type 02. Editorial changes throughout. - jak. 97-09-22 Thomas M. Hess C Changes IAW NOR 5962-058-98 jak. 98-03-27 Monica L. Poelking D Correct VOH3and IILin Table I. Editorial changes throughout jak. 99-11-24 Monica L. Poelking E Update

3、 boilerplate paragraphs to the current MIL-PRF-38535 requirements. - LTG 09-03-24 Thomas M. Hess REV SHET REV E E E E SHEET 15 16 17 18 REV STATUS REV E E E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby CHECKED BY Thanh V. Nguyen DEFENSE

4、SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil APPROVED BY Monica L. Poelking STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 93-12-15 MICROCIRCUIT, DIGITAL, ADVANCED BIPOLAR C

5、MOS, OCTAL TRANSCEIVER WITH THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-92148 SHEET 1 OF 18 DSCC FORM 2233 APR 97 5962-E205-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ST

6、ANDARD MICROCIRCUIT DRAWING SIZE A 5962-92148 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space applic

7、ation (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92

8、148 01 Q R A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA le

9、vels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit

10、function as follows: Device type Generic number Circuit function 01 54ABT245 Octal Bus transceiver with 3-state outputs TTL compatible inputs 02 54ABT245A Octal Bus transceiver with 3-state outputs TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter id

11、entifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-P

12、RF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead fi

13、nish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92148 DEFENSE SUPPLY CENTER C

14、OLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range except I/O ports (VIN) -0.5 V dc to +7.0 V dc 4/ DC output voltage range (VOUT) . -0.5 V dc to +5.5 V dc 4/

15、 DC input clamp current (IIK) -18 mA DC output clamp current (IOK) -50 mA DC output current (IOL) (per output). +96 mA Storage temperature range (TSTG). -65C to +150C Lead temperature (soldering, 10 seconds). +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ

16、) +175C Maximum power dissipation (PD) . 500 mW 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) (Operating) . +4.5 V dc to +5.5 V dc Input voltage range (VIN) +0.0 V dc to VCCOutput voltage range (VOUT). +0.0 V dc to VCC Maximum low level input voltage (VIL) 0.8 V Maximum high

17、 level input voltage (VIH) 2.0 V Case operating temperature range (TC). -55C to +125C Maximum input rise or fall rate (t/V). 5 ns/V Maximum high level output current (IOH) -24 mA Maximum low level output current (IOL) 48 mA 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handboo

18、ks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Ma

19、nufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standa

20、rd Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses above the absolute maximum rating may cause permanent damage

21、 to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to

22、 +125C. 4/ The input and output negative voltage ratings may be exceeded provided that the input and output clamp current ratings are observed. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92148 DEFENSE SU

23、PPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes

24、 applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Mana

25、gement (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construc

26、tion, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3

27、.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce test circuit and waveforms. The ground bounce tes

28、t circuit and waveforms shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.2.7 Radiation exposure circuit. The radiation exposure circuit shall be as specified when available. 3.3 Electrical per

29、formance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requiremen

30、ts. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking

31、 of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535.

32、 Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF

33、-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be requir

34、ed from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes

35、Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix

36、 A shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92148 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E S

37、HEET 5 DSCC FORM 2234 APR 97 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class

38、M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class

39、 M. Device class M devices covered by this drawing shall be in microcircuit group number 126 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92148 DEFENSE SUPPLY CENTER COLUMBU

40、S COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test condition 2/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Device type VCCGroup A subgroups Limits 3/ Unit Min Max Hi

41、gh level output voltage 3006 VOH1For all inputs affecting output under test VIN= 2.0 V or 0.8 V IOH= -3 mA All 4.5 V 1, 2, 3 2.5 V VOH2For all inputs affecting output under test VIN= 2.0 V or 0.8 V IOH= -3 mA All 5.0 V 1, 2, 3 3.0 VOH3For all inputs affecting output under test VIN= 2.0 V or 0.8 V IO

42、H= -24 mA All 4.5 V 1, 2, 3 2.0 Low level output voltage 3007 VOLFor all inputs affecting output under test VIN= 2.0 V or 0.8 V IOL= 48 mA All 4.5 V 1, 2, 3 0.55 V Three-state output leakage current high 3021 IOZH4/ 5/ For control inputs affecting output under test VIN= VIHor VIL VIH= 2.0 V VIL= 0.8

43、 V VOUT= 2.7 V All 5.5 V 1, 2, 3 10.0 A Three-state output leakage current high 3021 IOZL4/ 5/ For control inputs affecting output under test VIN= VIHor VIL VIH= 2.0 V VIL= 0.8 V VOUT= 2.7 V All 5.5 V 1, 2, 3 -10.0 A Negative input clamp voltage 3022 VIC-For input under test IIN= -18 mA All 4.5 V 1,

44、 2, 3 -1.2 V Off-state leakage current IOFFFor output under test VINor VOUT= 4.5 V All other pins at 0.0 V All 0.0 V 1 100.0 A High-state leakage current ICEXFor output under test VOUT= 5.5 V Outputs at high logic state All 5.5 V 1, 2, 3 50.0 A Input current high IIHFor input under test Control 01 5

45、.5 V 1, 2, 3 +2.0 A 3010 VIN= VCCinput 02 +1.0 6/ A or B ports All +100.0 Input current low IILFor input under test Control 01 5.5 V 1, 2, 3 -2.0 A 3010 VIN= GND input 02 -1.0 6/ A or B ports All -100.0 Output current 3011 IOUT 7/ VOUT= 2.5 V All 5.5 V 1, 2, 3 -50.0 -180.0 mA See footnotes at end of

46、 table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92148 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteri

47、stics - Continued. Test and MIL-STD-883 test method 1/ Symbol Test condition 2/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Device type VCCGroup A subgroups Limits 3/ Unit Min Max Quiescent supply current delta ICCFor input under test, VIN= VCCData inputs, outputs 01 5.5 V 1, 2, 3 2.5 m

48、A TTL input levels 3005 8/ For all other inputs VIN= VCCor GND enabled 02 1.5 Data inputs, outputs disabled All 5.5 V 1, 2, 3 50 A Control inputs 01 5.5 V 1, 2, 3 2.5 mA 02 1.5 Quiescent supply current, output high 3005 ICCHVIN= VCCor GND IOUT= 0.0 A A or B ports All 5.5 V 1, 2, 3 250.0 A Quiescent supply current, output low 3005 ICCLVIN= VCCor GND IOUT= 0.0 A A or B ports All 5.5 V 1, 2, 3 30.0 mA Quiescent supply current, output three-state 3005 ICCZVIN= VCCor GND IOUT= 0.0 A A or B ports All 5.5 V 1, 2, 3 250.0 A Input capacitance, control inputs CINSee 4.4.1b TC= +25