DLA SMD-5962-92181 REV B-2012 MICROCIRCUIT DIGITAL ADVANCED CMOS QUAD 2-INPUT NOR GATE TTL COMPATIBLE INPUTS MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update the boilerplate to current requirements as specified in MIL-PRF-38535. Editorial changes throughout. jak 06-08-16 Thomas M. Hess B Update boilerplate paragraphs to the current MIL-PRF-38535 requirements. - LTG 12-10-29 Thomas M. Hess REV S

2、HEET REV B B B SHEET 15 16 17 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR

3、 USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A CHECKED BY Thomas J. Ricciuti APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, ADVANCED CMOS, QUAD 2-INPUT NOR GATE, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON DRAWING APPROVAL DATE 93-06-07 REVISION LEVEL B SIZE A CAGE C

4、ODE 67268 5962-92181 SHEET 1 OF 17 DSCC FORM 2233 APR 97 5962-E014-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92181 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2

5、234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN).

6、When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92181 01 M C A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.

7、4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA

8、 levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54ACTQ02 Quad 2-input NOR gate, TTL compatible inputs 1.2.3 Device clas

9、s designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38

10、535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat

11、 pack 2 CQCC1-N20 20 Leadless-chip-carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROC

12、IRCUIT DRAWING SIZE A 5962-92181 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage (VIN) -0.5 V dc to VCC+ 0.5 V dc DC output voltage range (VOUT) .

13、-0.5 V dc to VCC+ 0.5 V dc DC input diode current (IIK) (VIN= -0.5 V and VCC+ 0.5 V) . 20 mA DC output diode current (IOK) (VOUT= -0.5 V and VCC+ 0.5 V). 20 mA DC output current (IOUT) (per output pin) 50 mA DC VCCor GND current (ICC, IGND) (per pin) . 400 mA Storage temperature range (TSTG) . -65C

14、to +150C Maximum power dissipation (PD) . 500 mW Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ). +175C 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Input voltage ra

15、nge (VIN) +0.0 V dc to VCCOutput voltage range (VOUT) . +0.0 V dc to VCCMaximum low level input voltage (VIL) 0.8 V Minimum high level input voltage (VIH) . 2.0 V Case operating temperature range (TC) . -55C to +125C Maximum input edge rate (V/t): (from VIN= 0.8 V to 2.0 V, 2.0 V to 0.8 V) . 125 mV/

16、ns Maximum high level output current (IOH) -24 mA Maximum low level output current (IOL) 24 mA 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless othe

17、rwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD

18、-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Stand

19、ardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. The maximum junction tempera

20、ture may be exceeded for allowable short duration burn-in screening conditions in accordance with method 5004 of MIL-STD-883. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case tempera

21、ture range of -55C to +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92181 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2.2 Non-Government publication

22、s. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents cited in the solicitation or contract. JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JESD20 - Standard for Description of 54/74ACXXXXX and 54/74ACTXX

23、XXX Advanced High-Speed CMOS Devices. JESD78 - IC Latch-Up Test. (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 North 10thStreet, Suite 240-S Arlington, VA 22201-2107). ASTM INTERNATIONAL (ASTM) ASTM F1192 - Standard Guid

24、e for the Measurement of Single Event Phenomena (SEP) Induced by Heavy Ion Irradiation of Semiconductor Devices. (Copies of this document is available online at http:/www.astm.org/ or from ASTM International, 100 Barr Harbor Drive, P. O. Box C700, West Conshohocken, PA 19428-2959). 2.3 Order of prec

25、edence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requir

26、ements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein.

27、 The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-

28、38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The trut

29、h table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce waveforms and test circuit. The ground bounce waveforms and test circuit shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switchi

30、ng waveforms and test circuit shall be as specified on figure 5. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall a

31、pply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted wi

32、thout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92181 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. Fo

33、r packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accord

34、ance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C

35、“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of co

36、mpliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufac

37、turers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for

38、device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this

39、 drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentat

40、ion. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 36 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo r

41、eproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92181 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol

42、Test conditions 2/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Device type 3/ and device class VCCGroup A subgroups Limits 4/ Unit Min Max High level output voltage 3006 VOH1For all inputs affecting output under test VIN= VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCCor GND IOH=

43、 -50 A All All 4.5 V 1, 2, 3 4.4 V VOH2For all inputs affecting output under test VIN= VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCCor GND IOH= -50 A All All 5.5 V 1, 2, 3 5.4 VOH3For all inputs affecting output under test VIN= VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCCor GND IO

44、H= -24 mA All All 4.5 V 1 3.86 2, 3 3.70 VOH4For all inputs affecting output under test VIN= VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCCor GND IOH= -24 mA All All 5.5 V 1 4.86 2, 3 4.70 VOH55/ For all inputs affecting output under test VIN= VIH= 2.0 V or VIL= 0.8 V For all other inputs VI

45、N= VCCor GND IOH= -50 mA All All 5.5 V 1, 2, 3 3.85 Low level output voltage 3007 VOL1For all inputs affecting output under test VIN= VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= +50 A All All 4.5 V 1, 2, 3 0.1 V VOL2For all inputs affecting output under test VIN= VIH= 2.0 V or

46、VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= +50 A All All 5.5 V 1, 2, 3 0.1 VOL3For all inputs affecting output under test VIN= VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= +24 mA All All 4.5 V 1 0.36 2, 3 0.50 See footnotes at end of table. Provided by IHSNot for Resale

47、No reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92181 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test and MIL-STD-883 test m

48、ethod 1/ Symbol Test conditions 2/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Device type 3/ and device class VCCGroup A subgroups Limits 4/ Unit Min Max Low level output voltage 3007 VOL4For all inputs affecting output under test VIN= VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= +24 mA All All 5.5 V 1 0.36 V 2, 3 0.50 VOL55/ For all inputs affecting output under test VIN= VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= +50 mA All All 5.5 V 1, 2, 3 1.65 Positive input clamp voltage 3022 VIC+For inpu