DLA SMD-5962-92202 REV D-2010 MICROCIRCUIT DIGITAL FAST CMOS DUAL 1-OF-4 DECODER WITH ENABLE TTL COMPATIBLE INPUTS AND LIMITED OUTPUT VOLTAGE SWING MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes are in accordance with the notice of revision 5962-R217-94. - tvn 94-06-16 Monica L. Poelking B Changes are in accordance with the notice of revision 5962-R222-96. - tvn 96-09-30 Monica L. Poelking C Update the boilerplate to the current

2、requirements of MIL-PRF-38535. - jak 08-01-28 Thomas M. Hess D Add footnote 8/ for test condition of total power supply current (ICCT) to table I. Update boilerplate paragraphs to current requirements of MIL-PRF-38535. - LTG 10-01-19 Thomas M. Hess REV SHET REV D D D SHEET 15 16 17 REV STATUS REV D

3、D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Thanh V. Nguyen DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING CHECKED BY Thanh V. Nguyen THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENT

4、S APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, FAST CMOS, DUAL 1-OF-4 DECODER WITH ENABLE, TTL COMPATIBLE INPUTS AND LIMITED OUTPUT VOLTAGE SWING, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-03-04 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 596

5、2-92202 SHEET 1 OF 17 DSCC FORM 2233 APR 97 5962-E142-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92202 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234

6、APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). Wh

7、en available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92202 01 M E A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) L

8、eadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA leve

9、ls and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01, 02 54FCT139T Dual 1-of-4 decoder with enable, TTL compatible inputs and lim

10、ited output voltage swing 03, 04 54FCT139AT Dual 1-of-4 decoder with enable, TTL compatible inputs and limited output voltage swing 05, 06 54FCT139CT Dual 1-of-4 decoder with enable, TTL compatible inputs and limited output voltage swing 1.2.3 Device class designator. The device class designator is

11、a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qual

12、ification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F GDFP2-F16 or CDFP3-F16 16 Flat pack 2 CQCC1-N20 20 Leadless chip carrier 1.

13、2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92202 DEFENSE SUPP

14、LY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) . -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC+ 0.5 V dc 4/ DC output voltage range (VOUT) -0.5 V dc to VCC+ 0.5 V dc

15、4/ DC input clamp current (IIK) (VIN= -0.5 V) . -20 mA DC output clamp current (IOK) (VOUT-0.5 V and +7.0 V) . 20 mA DC output source current (IOH) (per output) -30 mA DC output sink current (IOL) (per output) . +70 mA DC VCCcurrent (ICC) . 260 mA Ground current (IGND) +550 mA Storage temperature ra

16、nge (TSTG) -65C to +150C Case temperature under bias (TBIAS) -65C to +135C Lead temperature (soldering, 10 seconds) . +300C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Junction temperature (TJ) . +175C Maximum power dissipation (PD) 500 mW 1.4 Recommended operating conditions. 2/ 3/ S

17、upply voltage range (VCC) +4.5 V dc to +5.5 V dc Input voltage range (VIN) +0.0 V dc to VCCOutput voltage range (VOUT) . +0.0 V dc to VCCMaximum low level input voltage (VIL) . 0.8 V Minimum high level input voltage (VIH) . 2.0 V Case operating temperature range (TC) . -55C to +125C Maximum input ri

18、se or fall rate (t/V): (from VIN= 0.3 V to 2.7 V, 2.7 V to 0.3 V) 5 ns/V Maximum high level output current (IOH): Device types 01, 03, and 05 . -12 mA Device types 02, 04, and 06 . -6 mA Maximum low level output current (IOL) 32 mA 1/ Stresses above the absolute maximum rating may cause permanent da

19、mage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55

20、C to +125C. 4/ For VCC 6.5 V, the upper limit on the range is limited to 7.0 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92202 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D

21、SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in

22、 the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DE

23、PARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building

24、 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemptio

25、n has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not

26、 affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, an

27、d physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall b

28、e as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce load circuit and waveforms. The ground bounce load circuit and waveforms shall be as specified on figure 4.

29、3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation p

30、arameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. Provided by IHSN

31、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92202 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 3.5 Marking. The part shall be marked with the PIN listed in 1.2 h

32、erein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still

33、be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL

34、-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this dra

35、wing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply

36、 for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for

37、device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product see 6.2 herein) invol

38、ving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation.

39、Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 39 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reprod

40、uction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92202 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Sym

41、bol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified Device type VCCGroup A subgroups Limits 3/ Unit Min Max High level output voltage 3006 VOH14/ For all inputs affecting output under test VIH= 2.0 V VIL= 0.8 V For all other inputs VIN= VCCor GND IOH= -300 A All 4.5 V 1

42、, 2, 3 2.7 VCC-0.5 V VOH2IOH= -12 mA 01, 03, 05 4.5 V 1, 2, 3 2.4 VCC-0.5 IOH= -6 mA 02, 04, 06 2.4 VCC-0.5 IOH= -12 mA 2.0 VCC-0.5 Low level output voltage 3007 VOL14/ IOL= +300 A All 4.5 V 1, 2, 3 0.20 V VOL2 OL= +32 mA 4.5 V 1, 2, 3 0.50 Negative input clamp voltage 3022 VIC-For input under test,

43、 IIN= -15 mA 01, 03, 05 4.5 V 1, 2, 3 -1.3 V For input under test, IIN= -18 mA 02, 04, 06 -1.2 Input current high 3010 IIHFor input under test, VIN= VCCFor all other inputs, VIN= VCCor GND All 5.5 V 1, 2 +1.0 A 3 +5.0 Input current low 3009 IILFor input under test, VIN= GND For all other inputs, VIN

44、= VCCor GND All 5.5 V 1, 2 -1.0 A 3 -5.0 Output short circuit current 3011 IOS5/ For all inputs, VIN= VCCor GND VOUT= GND All 5.5 V 1, 2, 3 -60 -225 mA Dynamic power supply current ICCD4/ 6/ Outputs open 01, 03, 05 5.5 V 4, 5, 6 0.25 mA/ MHzBit02, 04, 06 0.30 Quiescent supply current delta, TTL inpu

45、t level 3005 ICC7/ For input under test VIN= 3.4 V For all other inputs VIN= VCCor GND All 5.5 V 1, 2, 3 2.0 mA Quiescent supply current, outputs high 3005 ICCHa = b = GND For all other inputs VIN= VCCor GND All 5.5 V 1, 2, 3 1.5 mA Quiescent supply current, outputs low 3005 ICCLAll 5.5 V 1, 2, 3 1.

46、5 mA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92202 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Elect

47、rical performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified Device type VCCGroup A subgroups Limits 3/ Unit Min Max Total supply current ICCT18/ 9/ Outputs open One output toggling fo= 10 MHz

48、50% duty cycle For nonswitching input, VIN= VCCor GND For switching inputs, VIN= VCCor GND 01, 03, 05 5.5 V 4, 5, 6 4.0 mA 02, 04, 06 4.5 For switching inputs, VIN= 3.4 V or GND 01, 03, 05 5.5 V 4, 5, 6 5.0 02, 04, 06 5.5 ICCT24/ 8/ 9/ Outputs open One output toggling on each decoder fo= 10 MHz 50% duty cycle For nonswitching input, VIN= VCCor GND For switching inputs, VIN= VCCor GND 01, 03, 05 5.5 V 4, 5, 6 6.5 02, 04, 06 7.5 For switching inputs, VIN= 3.4 V or GND 01, 03, 05 5.5 V 4, 5, 6 8.5 02, 04, 06 9.5 Input capacitance 3012 CIN10/ TC= +25C See 4.4.1b All GND 4 10 pF