DLA SMD-5962-92237 REV D-2013 MICROCIRCUIT DIGITAL FAST CMOS OCTAL BUFFER LINE DRIVER WITH THREE-STATE OUTPUTS TTL COMPATIBLE INPUTS AND LIMITED OUTPUT VOLTAGE SWING MONOLITHIC SIL.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change is in accordance with the notice of revision 5962-R177-93. mbk 93-06-18 Michael A. Frye B Change is in accordance with the notice of revision 5962-R099-94. tvn 94-03-09 Monica L. Poelking C Update the boilerplate to current requirements as

2、 specified in MIL-PRF-38535. Editorial changes throughout. jak 06-12-11 Thomas M. Hess D Update boilerplate paragraphs to the current MIL-PRF-38535 requirements. - LTG 13-05-16 Thomas M. Hess REV SHEET REV D D D SHEET 15 16 17 REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7

3、8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A CHECKED BY Thomas J. Ricciut

4、i APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, FAST CMOS, OCTAL BUFFER/LINE DRIVER WITH THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS AND LIMITED OUTPUT VOLTAGE SWING, MONOLITHIC SILICON DRAWING APPROVAL DATE 93-03-26 REVISION LEVEL D SIZE A CAGE CODE 67268 5962-92237 SHEET 1 OF 17 DSCC FORM 2

5、233 APR 97 5962-E381-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing do

6、cuments two product assurance class levels consisting of high reliability (device class Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness

7、 Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92237 01 M R A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Dra

8、wing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RH

9、A designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01, 02 54FCT541T Octal buffer/line driver with three-state outputs, TTL compatible inputs and limited output voltage swi

10、ng 03, 04 54FCT541AT Octal buffer/line driver with three-state outputs, TTL compatible inputs and limited output voltage swing 05, 06 54FCT541CT Octal buffer/line driver with three-state outputs, TTL compatible inputs and limited output voltage swing 1.2.3 Device class designator. The device class d

11、esignator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certifica

12、tion and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2 CQCC1-N20 20 Square lead

13、less chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 596

14、2-92237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) . -0.5 V dc to +7.0 V dc DC input voltage range (VIN) . -0.5 V dc to VCC + 0.5 V dc 4/ DC output voltage range (VOUT) -0.5 V dc to

15、VCC+ 0.5 V dc 4/ DC input clamp current (IIK) (VIN= -0.5 V) -20 mA DC output clamp current (IOK) (VOUT= -0.5V and +7.0 V) . 20 mA DC output source current (per output) (IOH) -30 mA DC output sink current (per output) (IOL) . +70 mA DC VCCcurrent (ICC) . 260 mA DC GND current (IGND) . +550 mA Storage

16、 temperature range (TSTG) -65C to +150C Case temperature range under bias (TBIAS) -65C to +135C Maximum power dissipation (PD) 500 mW Lead temperature (soldering, 10 seconds) . +300C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Junction temperature (TJ) . +175C 1.4 Recommended operatin

17、g conditions 2/ 3/ Supply voltage range (VCC) . +4.5 V dc to +5.5 V dc Input voltage range (VIN) . 0.0 V to VCC Output voltage range (VOUT) 0.0 V to VCCMaximum low level input voltage (VIL). 0.8 V Minimum high level input voltage (VIH) 2.0 V Case operating temperature range (TC) -55C to +125C Maximu

18、m input rise or fall rate (tr, tf): (from VIN= 0.3 V to 2.7 V, 2.7 V to 0.3 V) 5 ns/V Maximum high level output current (IOH): Devices 01, 03, and 05 . -6 mA Devices 02, 04, and 06 . -12 mA Maximum low level output current (IOL) . 48 mA 1/ Stresses above the absolute maximum rating may cause permane

19、nt damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified shall apply over the full specified VCCrange and case temperature range of -55C

20、to +125C. 4/ For VCC 6.5 V, the upper limit on the range is limited to 7.0 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSC

21、C FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solici

22、tation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF

23、 DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191

24、11-5094). 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. R

25、EQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or fu

26、nction as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall

27、be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.

28、3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce waveforms and test circuit. The ground bounce waveforms and test circuit shall be as specified on figure 4. 3.2.6 Switching waveforms an

29、d test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as speci

30、fied in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. Provided by IHSNot for ResaleNo reproduction

31、 or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers

32、 PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes

33、 Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for d

34、evice class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device c

35、lass M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing sh

36、all affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and

37、 V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involvi

38、ng devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and app

39、licable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 37 (see MIL-PRF-38535, appendix A). Provid

40、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD

41、-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Device type VCCGroup A subgroups Limits 3/ Unit Min Max High level output voltage 3006 VOH14/ For all inputs affecting output under test, VIN= VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCC

42、or GND IOH= -300 A 01, 03, 05 4.5 V 1, 2, 3 2.7 VCC-0.5 V 04, 02, 06 3.0 VCC-0.5 VOH2For all inputs affecting output under test, VIN= VIH= 2.0 V or VIL= 0.8 V For all other inputs, VIN= VCCor GND IOH= -6 mA 01, 03, 05 4.5 V 2.4 VCC-0.5 IOH= -12 mA 2.0 VCC-0.5 IOH= -12 mA 02, 04, 06 2.4 VCC-0.5 Low l

43、evel output voltage 3007 VOL14/ For all inputs affecting output under test, VIN= VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= +300 A All 4.5 V 1, 2, 3 0.20 V VOL2For all inputs affecting output under test, VIN= VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= +4

44、8 mA All 4.5 V 0.55 Three-state output leakage current high 3021 IOZH5/ 6/ OEm = VIHor VILVIL= 0.8 V VIH= 2.0 V For all other inputs VIN= VCCor GND VOUT= VCC01, 03, 05 5.5 V 1, 2 1.0 A 3 10.0 02, 04, 06 1, 2 1.0 3 10.0 Three-state output leakage current low 3020 IOZL5/ 6/ OEm = VIHor VILVIL= 0.8 V V

45、IH= 2.0 V For all other inputs VIN= VCCor GND VOUT= GND 01, 03, 05 5.5 V 1, 2 -1.0 A 3 -10.0 02, 04, 06 1, 2 -1.0 3 -10.0 Negative input clamp voltage 3022 VIC-For input under test, IIN= -18 mA 01, 03, 05 4.5 V 1, 2, 3 -1.2 V For input under test, IIN= -15 mA 02, 04, 06 -1.3 Input current high 3010

46、IIHFor input under test VIN= VCC For all other inputs VIN= VCCor GND 01, 03, 05 5.5 V 1, 2 1.0 A 3 5.0 02, 04, 06 1, 2 1.0 3 5.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-

47、92237 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Device type VCCGroup

48、A subgroups Limits 3/ Unit Min Max Input current low 3009 IILFor input under test VIN= GND For all other inputs VIN= VCCor GND 01, 03, 05 5.5 V 1, 2 -1.0 A 3 -5.0 02, 04, 06 1, 2 -1.0 3 -5.0 Input capacitance 3012 CIN7/ See 4.4.1c TC= +25C All GND 4 10 pF Output capacitance 3012 COUT7/ See 4.4.1c TC= +25C All GND 4 12 pF Short circuit output current 3005 IOS8/ For all inputs, VIN= VCCor GND VOUT= GND All 5.5 V 1, 2, 3 -60 -225 mA Dynamic power supply current ICCD4/ 9/ Outputs open All 5.5 V 4, 5, 6 0.25 mA/ MHzBIT Quiescent power supply current delta, TTL input levels 3005