DLA SMD-5962-92272 REV D-2008 MICROCIRCUIT DIGITAL FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER WITH SERIES RESISTOR AND THREE-STATE OUTPUTS TTL COMPATIBLE INPUTS AND LIMITED OUTPUT .pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes IAW NOR 5962-R286-94 tvn. 94-10-13 Monica L. Poelking B Changes IAW NOR 5962-R086-95 tvn. 95-03-15 Monica L. Poelking C Changes IAW NOR 5962-R048-97 tvn. 96-11-08 Monica L. Poelking D Redrawn with changes. Update the boilerplate to the cu

2、rrent requirements of MIL-PRF-38535. - jak 08-06-10 Thomas M. Hess REV SHEET REV D D D D SHEET 15 16 17 18 REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Thanh V. Nguyen STANDARD MICROCIRCUIT DRAWING CHECKED BY Thanh V. Nguyen DEFENSE

3、 SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, FAST CMOS, 16-BIT BIDIRECTIONAL TRANSCEIVER WITH SERIES RESISTOR AND THREE-STATE OUTPUTS, TTL AND AGENCIES OF THE DEPART

4、MENT OF DEFENSE DRAWING APPROVAL DATE 94-07-26 COMPATIBLE INPUTS,LIMITED OUTPUT VOLTAGE SWING, MONOLITHIC SILICON AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-92272 SHEET 1 OF 18 DSCC FORM 2233 APR 97 5962-E325-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without

5、license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92272 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q

6、and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the foll

7、owing example: 5962 - 92272 01 M X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PR

8、F-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(

9、s) identify the circuit function as follows: Device type Generic number Circuit function 01 54FCT162245T 16-bit bidirectional transceiver with series resistor and three-state outputs, TTL compatible inputs and limited output voltage swing 02 54FCT162245AT 16-bit bidirectional transceiver with series

10、 resistor and three-state outputs, TTL compatible inputs and limited output voltage swing 03 54FCT162245CT 16-bit bidirectional transceiver with series resistor and three-state outputs, TTL compatible inputs and limited output voltage swing 1.2.3 Device class designator. The device class designator

11、is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and q

12、ualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X GDFP1-F48 48 Flat pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q a

13、nd V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92272 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR

14、 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC+ 0.5 V dc 4/ DC output voltage range (VOUT) . -0.5 V dc to VCCInput clamp current (IIK) (VIN= -0.5V). -20 mA Output clamp current (IOK) (VOUT= -0.5V and+7.0 V) 2

15、0 mA DC output source current (IOH) per output -30 mA DC output sink current (IOL) per output. +70 mA DC VCCcurrent (ICC). 480 mA DC ground current (IGND) 1120 mA Storage temperature range (TSTG) . -65C to +150C Case temperature under bias (TBIAS) . -65C to +135C Lead temperature (soldering, 10 seco

16、nds). +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C Maximum power dissipation (PD) . 1.0 W 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Input voltage range (VIN) +0.0 V dc to VCCOutput voltage range

17、 (VOUT). +0.0 V dc to VCCMaximum low level input voltage(VIL). 0.8 V Maximum high level input voltage (VIH) 2.0 V Case operating temperature range (TC). -55C to +125C Maximum input rise or fall rate (t/V): (from VIN= 0.3 V to 2.7 V, 2.7 V to 0.3 V) 2.5 ns/V Maximum high level output current (IOH. -1

18、6 mA Maximum low level output current (IOL) 16 mA 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The lim

19、its for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ For VCC 6.5 V, the upper limit on the range is limited to 7.0 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAN

20、DARD MICROCIRCUIT DRAWING SIZE A 5962-92272 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of thi

21、s drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF

22、-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit

23、 Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. 2.2 Order of precedence. In the event of a c

24、onflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item

25、 requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item req

26、uirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. This drawing has been modified to allow the manufacturer to use the alternate die/fabrication requirements of paragraph A.3.2.2 of MIL-PRF-38535 or other alte

27、rnative approved by the Qualifying Activity. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlin

28、es. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.

29、5 Ground bounce load circuit and waveforms. The ground bounce load circuit and waveforms shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. Provided by IHSNot for ResaleNo reproduction or networki

30、ng permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92272 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specifie

31、d herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The e

32、lectrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer

33、 has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1

34、 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. For class Q product built in accordance with A.3.2.2 of MIL-PRF-3853

35、5 or other alternative approved by the Qualifying Activity, the “QD” certification mark shall be used in place of the “QML” or “Q” certification mark. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in orde

36、r to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior

37、 to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A

38、certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA

39、 of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affect this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facil

40、ity and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 37 (see MIL-PRF-38535, appendix

41、 A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92272 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristi

42、cs. Limits 3/ Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified Devicetype VCCGroup A subgroups Min Max Unit VOH14/ IOH= -300 A All 4.5 V 1, 2, 3 3.0 VCC-0.5High level output voltage 3006 VOH2For all inputs affecting output under

43、 test, VIN= 2.0 V or 0.8 V For all other inputs VIN= VCCor GND IOH= -16 mA All 4.5 V 1, 2, 3 2.4 V VOL14/ IOH= 300 A All 4.5 V 1, 2, 3 0.2 Low level output voltage 3007 VOL2For all inputs affecting output under test, VIN= 2.0 V or 0.8 V For all other inputs VIN= VCCor GND IOH= 16 mA All 4.5 V 1, 2,

44、3 0.55 V Negative input clamp voltage 3022 VIC-For input under test, IIN= -18 mA All 4.5 V 1, 2, 3 -1.2 V 1, 2 +1.0 Three-state output current high 3021 IOZH5/ 6/ mOE = 2.0 V *or 0.8 V For all other inputs, VIN= VCCor GND VOUT= VCCAll 5.5 V 3 +5.0 A 1, 2 -1.0 Three-state output current low 3020 IOZL

45、5/ 6/ mOE = 2.0 V or 0.8 V For all other inputs, VIN= VCCor GND VOUT= GND All 5.5 V 3 -5.0 A 1, 2 +1.0 Control pins All 5.5 V 3 +5.0 A 1, 2 +1.0 Input current high 3010 IIHFor input under test VIN= VCC For all other inputs VIN= VCCor GND I/O pins All 5.5 V 3 +5.0 A 1, 2 -1.0 Control pins All 5.5 V 3

46、 -5.0 A 1, 2 -1.0 Input current low 3009 IILFor input under test VIN= GND For all other inputs VIN= VCCor GND I/O pins All 5.5 V 3 -5.0 A Output current low 3011 IODL 7/ VIN= 2.0 V or 0.8 V VOUT= 1.5 V All 5.0 1, 2, 3 60 200 mA Output current high 3011 IODH 7/ VIN= 2.0 V or 0.8 V VOUT= 1.5 V All 5.0

47、 1, 2, 3 -60 -200 mA Short circuit output current 3011 IOS7/ For all inputs VIN= VCCor GND VOUT= GND All 5.5 V 1, 2, 3 -80 -250 mA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 596

48、2-92272 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Limits 3/ Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified Device type VCCGroup A subgroups Min Max Unit Dynamic power supply current ICCD4/ 8/ Outputs open All 5.5 V 4, 5, 6 100 A/ MHzBitQuiescent supply current delta, TTL input levels 3005 ICC9/ For input under test VIN= VCC 2.1 V For all other inputs VIN= VCCor GND All 5.5 V 1, 2, 3 1