DLA SMD-5962-92274 REV B-1996 MICROCIRCUIT DIGITAL FAST CMOS 16-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOP WITH SERIES RESISTOR AND THREE-STATE OUTPUTS TTL COMPATIBLE INPUTS AND LIMITED O.pdf

1、DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS POST OFFICE BOX 3990 COLUMBUS, OH 43216-5000 IN REPLY DSCC-VAC (Mr. T. Nguyen/(DSN)850-067 1/614-692-067 l/tvn) DEC O6 REFER TO SUBJECT: Notice of Revision (NOR) 5962-RO50-97 for Standard Microcircuit Drawing (SMD) 5962-92274 Militaryhdustry D

2、istribution The enclosed NOR is approved for use effective as of the date of the NOR. In accordance with MIL-STD- 1 O0 SMD holders should; as a minimum, handwrite those changes described in the NOR tc sheet 1 of the subject SMD. After completion, the NOR should be attached to the subject SMD for fut

3、ure reference. Those companies who were listed as approved sources of supply prior to this action have agreed to actions taken on devices for which they had previously provided DSCC a certificate of compliance. This is evidenced by an existing active current certificate of compliance on file at DSCC

4、 with a DSCC record of verbal coordination. The certificate of compliance for these devices is considered concurrence with the new revision unless DSCC is otherwise notified. If you have comments or questions, please contact Thanh Nguyen at (DSN)850-0671/(614)692-0671 1 Encl MONICA L. POELKING 1 Chi

5、ef, Custom Microelectronics Team Federal Recycling Program Printed on Recycled Paper Licensed by Information Handling Services1. DATE (YYMMDD) 96-1 1-08 NOTICE OF REVISION (NOR) THIS REVISION DESCRIBED BELOW HAS BEEN AUTHORIZED FOR THE DOCUMENT LISTED. ublic repocting wen, for this colleclion is est

6、imated to average 2 hwn par response, Muding the time for miming instnicti-s. yarctiing exjsting data scum% atherin and maintainin the data needed and completing and reviewing the collecai cd infomalion. Send rsgardm this burden estimate o( any ow add “B. Revisions description column; add “Changes i

7、n accordance with NOR 5962-R05-97“. Revisions date column; add “96-1 1-08“. Revision level block; change from “A“ to “6“. Rev status of sheets; for sheet 1, change from “A“ to “B. For sheet 7, add “B. Table I, output short circuit current, 10s; change maximum limit from “-225 mA“ to “-250 mA“ Table

8、I, output drive current, IO; delete this test completely. Revision level block: add “B. f. DATE SIGNED (YYMMDD) 96-1 1-08 c. DATE SIGNED (YYMMDD) 96-1 1-08 Licensed by Information Handling Serviceslo DESC-ELDC (Mr. Nguyen/(AV 986) 5 13-296-6023/tn) 3 1 1995 . SUBJECT: Notice of Revision (NOR) 5962-R

9、089-95 for Standardized Military Drawing (SMD) 5962-92274 Military/Industry Distribution The enclosed NOR is approved for use efYective as of the date of the NOR. in accordance with MIL-STD-100 SMD holders should, as a minimum, handwrite those changes described in the NOR to sheet 1 of the subject S

10、MD. After completion, the NOR should he attached to the subject SMD for future reference. Those companies who were listed as approved sources of supply prior 10 this action have agreed to actions taken on devices for which they had previously provided DESC a certificate of compliance. This is eviden

11、ced by an existing active current certificate of compliance on tile at DESC along with a DESC record of verbal coordination. The certificate of compliance for Ihm devices is considered concurrence with the new revision unless DESC is otherwise notifid. If you have comments or questions, please conta

12、ct Thanh Nguyen at (AV)986-6023 or (5 i 3)296-6023. 1 Encl c MONICA L. POELKING Chief, Custom Microelectronics Branc ti Licensed by Information Handling Services(YYMMDD) = 9999996 O066299 789 NOTICE OF REVISION (NOR) b. ADDRESS (Street, City, State, Zip Code) 4. OKIGINATOR a. TYPED NAME (First, Midd

13、le Initial, . Defense Electronics Supply Center 1507 Wilmington Pike Dayton, OH 45444-5765 Last) I 95-03-15 This revision described below has been authorized for the document Listed. 5. CAGE CODE 67268 7. CAGE CODE 67268 9. TITLE OF DOCUHENT MICROCIRCUIT, DIGITAL, FAST CMOS, 16-BIT EDGE-TRIGGERED D-

14、TYPE FLIP-FLOP WITH SERIES RESISTOR AND THREE-STATE OLTPUTS, TTL COMPATIOLE IIJPUTS AND LIMITED OUTPUT VOLTAGE SWING, MONOLITHIC SILICON Form Approved OHB No. 0704-0188 IO. REVISION LETTER a. b. NEU Initial A - 2. PROCURING ACTIVITY NO. a. (X one) 3. irODAAC X (1) Existing document supplemented by t

15、he NOR may be used in manufacture. (2) Revised document nust be received before manufacturer Iiay incorporate this change. (3) Custodian of pasfer document ;hsll rake above revision and furnish revised document. 6. NOR NO. 5962-RU89-95 8. DOCUMENT NO. 5962-92274 11. ECP NO. b. ACTIVITY AUTHORIZED TO

16、 APPROVE CHAHGE FOR EOVERHllENT NIA c. TYPED tiAIE (First, Middle Initial, Last) All 13. DESCRIPTION OF REVISION Sheet 1: Revisions ltr column; add “A“. Revisions description column; add “Changes in accordance with NOR 5962-R089-95“. Revisions date column; add “95-03-15“. Revision level block; add “

17、A“. Rev status of sheet; for sheets 1 and 6, add “A“. Table I, output current low, IODL;,change maximum limit from “150 mA“ to ?OC mA“. Table I, output current hlgh, IOD“ change maximum limit from “-150 mA“ to “-200 mA“. Revision level block; add “A“. Sheet 6: I I I 14. THIS SECTION FOR GOVERIIPIENT

18、 USE ONLY DESC-ELDC d. TITLE Chief, Custom Ilicrcelectronics 1%. ACTIVITY ACCOMPLISHIIIG REVISION DESC-ELDC OD fori 1695, APR 92 Monica L. Pc e. SIGNATURE Monica L. Poelkiy b. REVISION COMPLETED (Signature) Thar,h V. Nguycn Previous editions are obsolete f. DATE SIGNED (YYMMDD) 95-03-1 5 c. DATE SIG

19、NED (Y Y M MD D ) 95-03-15 Licensed by Information Handling Services9999996 00bb300 220 REVIS IONS I I I LTR DESCRIPTION DATE tYR-MO-DA) APPROVED =t-tT SHEET 18 I I I REV 1 I 19 I I I I I I REV STATUS OF SHEETS PMIC N/A STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMEN

20、TS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A iESC FORM 193 JUL 91 DISTRIBUTION STATEMENT A. -=-t+tT SHEET PREPARED BY Thanh V. Nguyen CHECKED BY Thanh V. Nguycn APPROVED BY Monica L. Poelking DRAUINC APPROVAL DATE 94-07-26 REVISION LEVEL i DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 4544

21、4 MICROCIRCUIT, DIGITAL, FAST CMOS, 16-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOP WITH SERIES RESISTOR AND THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS AND LIMITED OUTPUT VOLTAGE SWING, MONOLITHIC SILICON SIZE I CAGE CODE 1 5962-92274 A 67268 SHEET 1 OF 19 5962-E350-94 Approved for public release; distributi

22、on is unlimited. Licensed by Information Handling Services 1. SCOPE 1.1 Scope. This drawing forms a part of a one part - one part number documentation system (see 6.6 herein). TWO product assurance classes consisting of military high reliability (device classes Q and M) and space application (device

23、 class VI, and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). 1.2.1 of HIL-STD-883, “Provisions for the use of NIL-STD-883 in conjunction with conpliant non-JAN devices“. available, a choice of Radiation Hardness Assurance (RHA) l

24、evels are reflected in the PIN. Device class M microcircuits represent non-JAN class 6 microcircuits in accordance with Uhen I 1 1.2 M. The PIN shall be as shown in the following example: SI, i 92274 7 J, 1 1 1 Federal RHA Devi ce Devi ce Case Lead 1 stock class designator type class outline finish

25、I / (see 1.2.3) designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / Drawing number 1.2.1 RHA desiqnator. Device class M RHA marked devices shall meet the NIL-I-38535 appendix A specified RHA level and shall be marked with the appropriate RHA designator. MIL-1-38535 specified RHA

26、levels and shall be marked with the appropriate RHA designator. non-RHA device. Device classes Q and V RHA marked devices shall meet the A dash (-1 indicates a 1.2.2 Device type(s). The device typeCs) shall identify the circuit function as follows: I Device type Generic number Circuit function I o1

27、54FCT162374T 16-bit edge-triggered D-type flip-flop with series resistor and three-stat outputs, TTL compatible inputs and limited output voltage Suing l-bit edge-triggered D-type flip-flop with series resistor and three-stat outputs, TTL compatible inputs and limited output voltage suing 16-bit edg

28、e-triggered D-type f lip-f top with series resistor and three-stat outputs, TTL compatible inputs and limited output voltage swing 02 54FCT162374AT 03 54FCT162374CT assurance level as follows: 1.2.3 Device class desiqnator. lhe device class designator shall be a single letter identifying the product

29、 Devi ce class Devi ce requirements documentation M Vendor self-certification to the requirements for non-JAN class B microcircuits in accordance with 1.2.1 of MIL-STD-883 Q or V Certification and qualification to MIL-1-38535 1.2.4 Case outLineCs). The case outLineCs) shall be as designated in MIL-S

30、TD-1835, and as follows: Out line letter Descriptive desianator Terni na 1s Package style X GDFPI-Fa 48 Flat pack 1.2.5 Lead finish. The lead finish shall be as specified in MIL-STD-883 (see 3.1 herein) for class R or MIL-1-38535 for classes (1 and V. The “X designation is for use in specifications

31、when lead finishes A, 6, and C are considered acceptable and interchangeable without preference. Finish letter “X“ shall not be marked on the microcircuit or its packaging. STANDARD 5962-92274 MICROCIRCUIT DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 , * DESC FORM 193A JUL 91 License

32、d by Information Handling ServicesSupply voltage range (V ) - - - - - - - - - - - - - - - - - - C input voltage range FS N) - - - - - - - - - - - - - - - - - DC output voltage range (6, T) - - - - - - - - - - - - - - - - DC input clamp current (i J (v = -0.5 v ) - - - - - - - - - DC output clamp cur

33、rent (iw) dWT -0.5 V and +7.0 V) - - - - DC output source current (I - - - - - - - - - DC output sink current IOLy(per output) - - - - - - - - - - ) (per output) DC V current (ICC) - - - - - - - - - - - - - - - - - - - Grouni current (IGND) - - - - - - - - - - - - - - - - - - - - Storage temperature

34、 range (T 1 - - - - - - - - - - - - - - - Case temperature under bias - - - - - - - - - - - - - Lead temperature (soldering, 18 seconds) - - - - - - - - - - - Thermal resistance, junction-to-case (Jc) - - - - - - - - - - Junction temperature (TJ) - - - - - - - - - - - - - - - - - - Maximum power dis

35、sipation (PD) - - - - - - - - - - - - - - - - SIZE STANDARD A MICROCIRCUIT DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 REVISION LEVEL 1.4 Recommended operating conditions. 2/ I/ 5962-92274 SHEET 3 Supply voltage range (Vc ) - - - - - - - - - - - - - - - - - - input voltage range (V

36、Nt - - - - - - - - - - - - - - - - - - utput voltage range dOUT) - - - - - - - - - - - - - - - - - Maximum low level input voltage (VIL) - - - - - - - - - - - - Minimum high level input voltage (VI,) - - - - - - - - - - - - Case operating temperature range (T ) - - - - - - - - - - - - Maximum input

37、rise or fall rate (AtSAv): - - - - - - - - Maximum high level output current (I - - - - - - - - - - - Maximum low level output current (I,:! - - - - - - - - - - - - (from VIN = 0.3 V to 2.7 V, 2.7 V to 0.3 V) ) -0.5 V dc to +7.0 V dc -0.5 V dc to Vcc + 0.5 V dc -0.5 V dc to Vcc s/ -20 mA i20 iA +70

38、inA *480 mA +I120 mh -30 niA -65C to +150C -65C to +135“C +3oO0c See MIL-STO-1835 +17S0C 1.0 u +4.5 V dc to +5.5 V dc +O.O V dc to Vcc 0.8 V 2.0 v -55C to +125C +o.o v dc to vcc 2.5 ns/V -16 mA 16 mA 1.5 Diaital Logic testing for device classes Q and V. Fault coverage measurement of manufacturing lo

39、gic tests (MIL-STO-883, test method 5012) - - - - - - - - XX percent s/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, bulletin, and handbook. Unless otherwise specified, the follouing specification, standards, bulletin, and handbook of the issue listed in that issue of the Departm

40、ent of Defense Index of Specifications and Standards specified in the solicitation, form a part of this drawing to the extent specified herein. Licensed by Information Handling ServicesSPECIFICATION MILITARY MIL-1-38535 - STANDARDS MILITARY MIL-STD-883 - MIL-STD-973 - MIL-STD-1835 - BULLETIN MILITAR

41、Y MIL-WL-103 - HANDBOOK HI LITARY HIL-HDBK-780 - Integrated Circuits, Manufacturing, General Specification for. Test Methods and Procedures for Microelectronics. configuration Management. Microcircuit Case Outlines List of Standardized Military Drawings (SMDs) Standardized Mi Litary Drawings. (Copie

42、s of the specification, standards, bulletin, and handbook required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Order of precedence. In the event of a conflict between the text of

43、this drawing and the references Cited herein,.the text of this drawing shall take precedence. 3. REQUIREMENTS 3.1 The individual item requirements for device class M shall be in accordance with 1.2.1 Of MIL-STD-883, “Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices

44、,“ and as specif led herein. device manufacturers Quality Management (QH) plan, and as specified herein. item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-1-38535, the 3.2 Design, construction, and physical dimensions. The design, construc

45、tion, and physical dimensions shall be as specified in MIL-STD-883 (see 3.1 herein) fop device class H and MIL-1-38535 for device classes Q and V and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. 3.2.3 Truth table. The terminal con

46、nections shall be as specified on figure I. ! The truth table shall be as specified on figure 2. 3.2.4 Lwic di-ram. The logic diagram shall be as specified on figure 3. 9 3.2.5 Ground bounce Load circuit and waveforms. The ground bounce load circuit and uaveformsbhall be as specified on figure 4. 3.

47、2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation par

48、ameter limits are as specified in table I and shall apply over the full case operating temperature range. and limits are as specified in table I. Test conditions for these specified characteristics 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in

49、 table II- The electric81 teats for each subgroup ere defined in table I. STANDARD MICROCIRCUIT DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 5962-92274 I 1 REVISION LEVEL SHEET I4 I 1 DESC FORM 193A JUL 91 Licensed by Information Handling Services- m b O066304 976 m SIZE STANDARD A MICROCIRCUIT DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 REVISION LEVEL 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. Harking for device class M shall be in iccordance with MIL-STD-883 (see 3.1 herein). 1IL-B