DLA SMD-5962-92283 REV B-1996 MICROCIRCUIT DIGITAL FAST CMOS 16-BIT REGISTERED TRANCEIVER WITH SERIES RESISTOR AND THREE-STATE OUTPUTS TTL COMPATIBLE INPUTS AND LIMITED OUTPUT VOLT.pdf

1、 SND-59b2-92283 REV B b 0090902 84T DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS POST OFFICE BOX 3990 COLUMBUS, OH 43216-5000 IN REPLY DEC O 6 1996 REFER TO DSCC-VAC (Mr. T. Nguyen/(DSN)850-0671/6 14-692-0671/tvn) SUBJECT: Notice of Revision (NOR) 5962-R054-97 for Standard Microcircuit D

2、rawing (SMD) 5962-92283 Militaryflndustry Distribution The enclosed NOR is approved for use effective as of the date of the NOR. In accordance with MIL-STD-100 SMD holders should, as a minimum, handwrite those changes described in the NOR to sheet 1 of the subject SMD. After completion, the NOR shou

3、ld be attached to the subject SMD for future reference. Those companies who were listed as approved sources of supply prior to this action have agreed to actions taken on devices for which they had previously provided DSCC a certificate of compliance. This is evidenced by an existing active current

4、certificate of compliance on file at DSCC with a DSCC record of verbal coordination. The certificate of compliance for these devices is considered concurrence with the new revision unless DSCC is otherwise notified. If you have comments or questions, please contact Thanh Nguyen at (DSN)850-067 1/(61

5、4)692-O67 1. 1 Encl MONICA L. POELKING - Microelectronics Team Chief, Custom Federal Recycling Program Printed on Recycled Paper Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SMD-59b2-92283 REV B = 9997996 0070903 78b I. TYPED NAME (First, Middle I

6、nitial, Last) L 3990 E. Broad Street Columbus, OH 4321 6-5000 NOTICE OF REVISION INOR) 7. CAGE CODE 67268 ublic repomng brtien ior mis clecon IS estimateci to average 2 hain pa response inciudmp w bme ior rensmng insucons aearaiing witting dala soums athain and main$ini . Send ammnts mpiin mis burde

7、n estimate or *y om add “B. Revisions description column; add “Changes in accordance with NOR 5962-R054-97“. Revisions date column; add “96-1 1-08“. Revision level block; change from “A to “B. Rev status of sheets; for sheets I and 6, change from “A to “B. Table I, output short circuit current, los;

8、 change maximum limit from “-225 mA“ to “-250 mA“. Table I, output drive current, lo; delete this test completely. Revision level block; change from “A“ to “B. f. DATE SIGNED (WMMDD) 96-1 1-08 14. THIS SECTION FOR GOVERNMENT USE ONLY 15a. ACTIVITY ACCOMPLISHING REVISION DSCC-VAC b. REVISION COMPLETE

9、D (Signature) Thanh V. Nguyen c. DATE SIGNED (WMMDD) 96-1 1-08 DD Form 1695, APR 92 Previous editions are obsolete. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-9999996 00bB23b 3BT DEFENSE LOGISTICS AGENCY pasrlrUr f DEFENSE ELECTRONICS SUPPLY CEN

10、TER DAVON, OH 45444-5765 IN REPLY REFER To DESC-ELDC (Mr. Nguyen/(AV 986) 5 13-296-6023/tvn) SUBJECT: Notice of Revision (NOR) 5962-R090-95 for Standardized Military Drawing (SMD) 5962-92283 Military/Industry Distribution The enclosed NOR is approved for use effective as of the date of the NOR. In a

11、ccordance with MIL-STD-100 SMD holders should, as a minimum, handwrite those changes described in the NOR to sheet 1 of the subject SMD. After completion, the NOR should be attached to the subject SMD for future reference. Those companies who were listed as approved sources of supply prior to this a

12、ction have agreed to actions taken on devices for which they had previously provided DESC a certificate of compliance. This is evidenced by an existing active current certificate of compliance on file at DESC along with a DESC record of verbal coordination, The certificate of compliance for these de

13、vices is considered concurrence with the new revision unless DESC is otherwise notified. If you have comments or questions, please contact Thanh Nguyen at (AV)986-6023 or (5 13)296-6023. 1 Encl MONICA L. POELKING Chief, Custom Microelectronics Branch Provided by IHSNot for ResaleNo reproduction or n

14、etworking permitted without license from IHS-,-,-9999996 0068237 216 DATE NOTICE OF REVISION (NOR) Im-Lproved YYMMDD) OMB No. 07044188 b. ADDRESS (Street, City, State, Zip Code) 5. CAGE CODE 4. ORIGINATOR a. TYPED NAME (First, Middle Initial, Defense Electronics Supply Center 67268 1507 Wilmington P

15、ike Dayton, OH 45444-5765 7. CAGE CODE 67268 Last) I 95-04-04 This revision described below has been authorized for the document listed. 6. NOR NO. 5962-R090-95 8. DOCUMENT NO. 5962-92283 2. PROCURING I ACTIVITY NO. 9. TITLE OF DOCUMENT MICROCIRCUIT, DIGITAL, FAST CMOS, 16-BIT REGISTERED TRANSCEIVER

16、 WITH SERIES RESISTOR AND THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS AND LIMITED OUTPUT VOLTAGE SWING, MONOLITHIC SILICON Public reporting burden for this collection is estimated to average 2 hours per response the time for reviewin data needed and compqeting and revieulng the collection of informat

17、ion. Send comments regarding this burdenestimate or an other aspect of this collection of information, including suggestions for reducin this burden, !o De artment of Defense Washingtion Headquarters Services Directorate for Informa?ion Operations and le rts, 1215 Jeffebon Davis Highway Surte 1204,

18、Arlin ton VA 22202-4302, and to the Office of Rana ement and Bud et Paperwork Rehuction Pro ect (07 add “A“. Revisions description column; add “Changes in accordance with NOR 5962-R090-95“. Revisions date column; add “95-04-04“. Revision level block; add “A“. Rev status of sheets; for sheets 1 and 6

19、, add “A“. f. DATE SIGNED (YYMMDD) Sheet 6: Table I, output current low, IODL;.change maximum limit from “150 mA“ to “200 mA“. Table I, output current high, IOD“ change maximum limit from “-150 mA“ to “-200 mA“. Revision level block; add “A“. Chief, Custom Microelectronics DESC-ELDC I Thanh V. Nguye

20、n l 95-04-04 Monica L. Poelking 95-04-04 b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FOR GOVERNMENT c. TYPED NAME (First, Middle Initial, Last) c. DATE SIGNED (YYMMDD) I 15a. ACTIVITY ACCOMPLISHING REVISION b. REVISION COMPLETED (Signature) DD Fori 1695, APR 92 Previous editions are obsolete Provided b

21、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-LTR DESCRIPTION DATE (YR-HO-DA) APPROVED PMIC NIA REV SHEET REV SHEET STANDARD MICROCIRCUIT DRAWING 15 16 17 THIS DRAWING IC AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE Thanh V.

22、 Nguyen . APPROVED BY Monica L. Poelking AMSC NIA MICROCIRCUIT, DIGITAL, FAST CMOS, 16-BIT REGISTERED TRANSCEIVER WITH SERIES RESISTOR AND THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS AND LIMITED OUTPUT VOLTAGE SWING, )ESC FORM 193 JUi 91 DISTRIBUTION STATERENT A. DRAWING APPROVAL DATE 94-09-07 PREPAR

23、ED BY Thanh V. Nguyen MONOLITHIC SILICON I I I DEFENSE ELECTRONICS SUPPLY CENTER REVISION LEVEL DAYTON, OHIO 45444 I 5962-92283 SIZE CAGE CODE 67268 A CHECKED BY 1 SHEET 1 OF 19 I 5962-E394-94 Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or net

24、working permitted without license from IHS-,-,-b 0068237 099 1. SCOPE 1.1 Scape. This drawing forms a part of a one part - one part number documentation system (see 6.6 herein). TWO product assurance classes consisting of military high reliability (device classes Q and M) and space application (devi

25、ce class V), and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). 1.2.1 of MIL-STD-883, “Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices“. available, a choice of Radiation Hardness Assurance (RHA)

26、 levels are reflected in the PIN. Device class M microcircuits represent non-JAN class B microcircuits in accordance with Uhen 1.2 m. The PIN shall be as shown in the following example: - -7- I T- I T I T- 5962 92283 I I I Lead Case Devi ce 1 Devi ce RHA Federal stock class designator type class out

27、line finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA desiqnator. Device class M RHA marked devices shall meet the MIL-1-38535 appendix A specified RHA levels and shall be marked with the appropriate RHA designator. MIL-1-38535 spe

28、cified RHA levels and shall be marked with the appropriate RHA designator. non-RHA device. Device classes Q and V RHA marked devices shall meet the A dash (-) indicates a 1.2.2 Device type(s). The device typels) shall identify the circuir function as follows: Device type Generic number Circuit funct

29、ion o1 54FCT162952AT 16-bit registered transceiver with series resistor and three-state outputs, TTL compatible inputs and limited output voltage swing 02 54FCT162952BT 16-bit registered transceiver with series resistor and three-state outputs, TTL compatible inputs and limited output voltage swing

30、03 54FCT162952CT 16-bit registered transceiver with series resistor and three-state outputs, TTL compatible inputs and limited output voltage suing 1.2.3 Device class desiqnator. The device class designator shall be a single letter identifying the product assurance level as follows: Device class Dev

31、ice requirements documentation M Vendor self-certification to the requirements for non-JAN class 6 microcircuits in accordance with 1.2.1 of MIL-STD-883 Q or V Certification and qualification to MIL-1-38535 1.2.4 Case outline(s1. The case outLineCs) shall be as designated in MIL-STD-1835, and as fol

32、lows: Outline letter Descriptive designator Termi na 1s Package style X GDFPI-F56 56 Flat pack 1.2.5 Lead finish. The lead finish shall be as specified in MIL-STD-883 (see 3.1 herein) for class tl or MIL-1-38535 for classes Q and V. designation is for use in specifications when lead finishes A, 8, a

33、nd c are considered acceptable and interchangeable without preference. Finish letter “X“ shall not be marked on the microcircuit or its packaging. The “X“ STANDARD 5962-92283 MICROCIRCUIT DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A JUL 91 Provided by IHSNot for Resale

34、No reproduction or networking permitted without license from IHS-,-,-9 9999996 O068240 800 STANDARD MICROCIRCUIT DRAWING 1.3 1.4 1.5 SIZE A 5962-92283 Absolute maximum ratings. 11 21 3/ Supply voltage range (V c) - - - - - - - - - - - - - - - - - - DC input voltage range LIN) - - - - - - - - - - - -

35、 - - - - - DC output voltage range (Vo T) - - - - - - - - - - - - - - - - DC input clamp current (II$ (V = -0.5 V 1 - - - - - - - - - DC output clamp current (IoK) (hour -0.5 V and t7.0 V) - - - - DC output source current (I 1 (per output) - - - - - - - - - DC output sink current (IOr(per output) -

36、- - - - - - - - - DC V current (Icc) - - - - - - - - - - - - - - - - - - - - Grouhs current (IGND) - - - - - - - - - - - - - - - - - - - - Storage temperature range (T - - - - - - - - - - - - - - - Case temperature under bias 8G:As) - - - - - - - - - - - - - Lead temperature (soldering, 11 seconds)

37、- - - - - - - - - - - Thermal resistance, junction-to-case (OJc) - - - - - - - - - - Junction temperature (TJ) - - - - - - - - - - - - - - - - - - Maximum power dissipation (PD) - - - - - - - - - - - - - - - - Recommended operatinq conditions. 2/ 3/ Supply voltage range (Vc ) - - - - - - - - - - - -

38、 - - - - - - Input voltage range (VIN$ - - - - - - - - - - - - - - - - - - Output voltage range (VOUT) - - - - - - - - - - - - - - - - - Maximum low level input voltage (VIL) - - - - - - - - - - - - Minimum high level input voltage (VI ) - - - - - - - - - - - - Case operating temperature range T Y -

39、 - - - - - - - - - - - Maximum input rise or fall rate (At5AV): - - - - - - - - Maximum hTgh level output current (I ) - - - - - - - - - - - Maximum low level output current (Io? - - - - - - - - - - - - Digital logic testing for device classes Q and V. Fault coverage measurement of manufacturing (fr

40、om VIN = 0.3 V to 2.7 V, 2.7 V to 0.3 VI logic tests (MIL-STD-883, test method 5012) - - - - - - - - -0.5 V dc to t7.0 V dc -0.5 V dc to Vcc + 0.5 V dc -0.5 V dc to Vcc $1 -20 mA I20 RA -30 mA t70 mA e480 mA t1120 aA -65C to +15OoC -65C to t135C +300C See MIL-STD-1835 +175C 1.0 w +4.5 V dc to +5.5 V

41、 dc +O.O V dc to Vcc +O.O V dc to Vcc 0.8 V 2.0 v -55C to +125C 2.5 ns/V 16 mA -16 ntA XX percent 51 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, bulletin, and handbook. Unless otherwise specified, the following specification, standards, bulletin, and handbook of the issue listed

42、 in that issue of the Department of Defense Index of Specifications and Standards specified in the solicitation, form a part of this drawing to the extent specified herein. I/ Stresses above the absolute maximum rating may cause permanent damage to the device. maximum levels may degrade performance

43、and affect reliabi lity. 2/ Unless otherwise noted, all voltages are referenced to GND. I/ The limits for the parameters specified herein shall apply over the full specified Vcc range and case temperature range of -55C to +125“C. For Vcc 2 6.5 V, the upper limit on the range is limited to 7.0 V. Val

44、ues will be added when they become avaitabte. Extended operation at the - 4/ - 5/ I DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 I REVISION LEVEL I SHEET3 DESC FORM 193A JUL 91 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-b 00b824L 747 SIZ

45、E STANDARD A MICROCIRCUIT DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 REVISION LEVEL SPECIFICATION MILITARY HIL-1-38535 STAN DARDS MILITARY ML-STD-883 WIL-STD-973 NI L-STD-1835 BULLETIN MILITARY MIL-BUL-103 HANDBOOK MILITARY MIL-HDBK-780 5962-92283 SHEET 4 - integrated Circuits, Man

46、ufacturing, General Specification for - Test Methods and Procedures for Microelectronics. - Configuration Management. - Microcircuit Case Outlines - List of Standardized Military Drawings (SFIDS). Standardized Military Drawings. (Copies of the specification, standards, bulletin, and handbook require

47、d by manufacturers in connection with Specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this dr

48、awing shall take precedence. 3. REQUIREMENTS 3.1 The individual item requirements for device ctass i4 shall be in accordance with 1.2.1 of MIL-STD-883, “Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices“ and as specified herein. device manufacturers Quality Manageme

49、nt (QM) plan, and as specified herein. Item requirements. The individual item requirements for device classes Q and V shall be in accordance with HIL-1-38535, the 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-STD-883 (see 3.1 herein) for device class M and MIL-1-38535 for device classes Q and V and herein. 3.2