DLA SMD-5962-93004 REV B-2013 MICROCIRCUIT LINEAR QUAD OPERATIONAL AMPLIFIER WITH VOLTAGE REFERENCE MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - ro 06-01-18 R. MONNIN B Drawing updated to reflect current MIL-PRF-38535 requirements. - ro 13-11-20 C. SAFFLE REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6

2、 7 8 9 10 11 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH PITHADIA APPROVED BY MICHAEL

3、 FRYE MICROCIRCUIT, LINEAR, QUAD OPERATIONAL AMPLIFIER WITH VOLTAGE REFERENCE, MONOLITHIC SILICON DRAWING APPROVAL DATE 94-06-22 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-93004 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E428-13 Provided by IHSNot for ResaleNo reproduction or networking per

4、mitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93004 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device clas

5、s Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the f

6、ollowing example: 5962 - 93004 01 M E A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the M

7、IL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device

8、type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 LM614A Quad, operational amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements docum

9、entation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 an

10、d as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reprodu

11、ction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93004 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Voltage on any pins except VR. -0.3 V to 36 V Current through any

12、 input pin and VRpin . 20 mA Differential input voltage . 36 V Lead temperature (soldering, 10 seconds) +260C Storage temperature range . -65C to +150C Junction temperature (TJ) . +150C Thermal resistance, junction-to-ambient (JA) 100C/W Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 1

13、.4 Recommended operating conditions. Positive supply voltage (+VS) +5 V Negative supply voltage (-VS) . GND, 0 V Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbo

14、oks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF

15、DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents a

16、re available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this draw

17、ing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performanc

18、e and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93004 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirem

19、ents. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. T

20、he individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38

21、535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance char

22、acteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The el

23、ectrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the en

24、tire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking f

25、or device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, ap

26、pendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a

27、manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device c

28、lasses Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, a

29、ppendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any chang

30、e that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall

31、be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 49 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitte

32、d without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93004 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A su

33、bgroups Device type Limits 2/ Unit Min Max Total supply current ICC+VS= 4 V to 36 V, 1 01 940 A RL= 2,3 1000 Supply voltage range VS1 01 2.8 36 V 2,3 3 36 Operational amplifier section. Offset voltage over 3/ +VSrange VIO1+VS= 4 V to 36 V 1 01 -3.5 3.5 mV 2,3 -6 6 Offset voltage over VCMrange VIO2VC

34、M= 0 V to VCM= +VS-1.4 V, +VS= 30 V 1 01 -3.5 3.5 mV VCM= 0 V to VCM= +VS-1.8 V, +VS= 30 V 2,3 -6 6 Input bias current IIB1 01 -25 25 nA 2,3 -30 30 Input offset current IIO1 01 -4 4 nA 2,3 -5 5 Common mode rejection ratio CMRR VCM= 0 V to +VS-1.4 V, VS= 30 V, CMRR = 20 log VCM/ VIO1 01 80 dB VCM= 0

35、V to +VS-1.8 V, VS= 30 V, CMRR = 20 log VCM/ VIO2,3 75 Power supply rejection ratio PSRR +VS= 4 V to 30 V, VCM= +VS/ 2, 1 01 80 dB PSRR = 20 log VCM/ VIO2,3 75 Output source current IOUTVOUT= +VS= -2.5 V, 1 01 20 mA +VIN= 0 V, -VIN= -0.3 V 2,3 13 See footnotes at end of table. Provided by IHSNot for

36、 ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93004 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditio

37、ns 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Operational amplifier section - Continued. Output sink current ISINKVOUT= 1.6 V, 1 01 14 mA +VIN= 0 V, -VIN= -0.3 V 2,3 8 Short circuit current ISCSource, VOUT= 0 V, 1 01 50 mA +VIN= 3 V, -VIN= 2 V 2,

38、3 60 Sink, VOUT= 5 V, 1 60 +VIN= 2 V, -VIN= 3 V 2,3 80 Output voltage swing high VOH+VS= 36 V, RL= 10 k to GND 4 01 +VS-1.7 V 5,6 +VS-1.9 Output voltage swing low VOL+VS= 36 V, RL= 10 k to +VS4 01 +VS+0.9 V 5,6 +VS+1.0 Open loop voltage gain AV+VS= 30 V, VOUT= 5 V to 25 V, RL= 10 k 4 01 100 V/mV 5,6

39、 40 Slew rate 4/ SR +VS= 30 V 7 01 0.55 V/s 8 0.45 Voltage reference section. Voltage reference 5/ VRTA= +25C 1 01 1.2365 1.2515 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 596

40、2-93004 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Voltage reference

41、 section - Continued. VRchange with 6/ current VR/ IRVR(100 A) - VR(17 A) 1 01 -1 1 mV 2,3 -1.1 1.1 VR(10 mA) - VR(100 A) 1 -5 5 2,3 -5.5 5.5 Resistance 7/ R VR(10 mA to 100 A) / 1 01 .51 9.9 mA 2,3 .56 VR(100 A to 17 A) / 1 12 83 A 2,3 13 VRchange with high VROVR/ VROVR(VRO= VR) - VR(VRO- 6.3 V), 1

42、 01 7 mV (5.06 V between anode and FEEDBACK) 2,3 10 VRchange with +VSchange VR/ VR(+VS= 5 V) - 1 01 -1.2 +1.2 mV +VSVR(+VS= 36 V) 2,3 -1.3 +1.3 VR(+VS= 5 V) - 1 -1 +1 VR(+VS= 3 V) 2,3 -1.5 +1.5 FEEDBACK bias current IFBVFB= VANODEto 5.06 V 1 01 35 nA 2,3 40 1/ Unless otherwise specified, +VS= 5 V, -

43、VS= 0 V = GND, VCM= VOUT= +VS/2, IR= 100 A, and FEEDBACK pin shorted to GND. 2/ The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as conventional current flow out of a device terminal. 3

44、/ For 4 V supply, actual test condition is +VS= +2 V and -VS= -2 V. For 36 V supply, actual test condition is +VS= +18 V and -VS= -18 V. 4/ Slew rate is measured with the operational amplifier in a voltage follower configuration. For rising slew rate, the input voltage is driven from 5 V to 25 V, an

45、d the output voltage transition is sampled at 10 V and 20 V. For falling slew rate, the input voltage is driven from 25 V to 5 V, and the output voltage transition is sampled at 20 V and 10 V. 5/ VROis the reference output voltage, which may be set for 1.2 V to 6.3 V. VRis the VRO-to-FEEDBACK voltag

46、e (nominally 1.244 V). 6/ Low contact resistance is required for accurate measurement. 7/ Guaranteed by VRchange with current. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93004 DLA LAND AND MARITIME COLUM

47、BUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outline E Terminal number Terminal connection 1 OUTPUT 1 2 -INPUT 1 3 +INPUT 1 4 +VS5 +INPUT 2 6 -INPUT 2 7 OUTPUT 2 8 FEEDBACK 9 CATHODE 10 OUTPUT 3 11 -INPUT 3 12 +INPUT 3 13 -VS14 +INPUT 4 15 -INPUT 4 16 OUTPU

48、T 4 FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93004 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturers Quality Management