DLA SMD-5962-93154 REV B-2012 MICROCIRCUIT HYBRID MEMORY 128K X 8-BIT ELECTRICALLY ERASABLE PROGRAMMABLE READ ONLY MEMORY.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to the current requirements of MIL-PRF-38534. 05-08-02 Raymond Monnin B Updated drawing paragraphs. -sld 12-07-10 Greg Cecil REV SHEET REV B B SHEET 15 16 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9

2、 10 11 12 13 14 PMIC N/A PREPARED BY Steve Duncan DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, MEMO

3、RY, 128K X 8-BIT, ELECTRICALLY ERASABLE PROGRAMMABLE READ ONLY MEMORY AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 93-03-23 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-93154 SHEET 1 OF 16 DSCC FORM 2233 APR 97 5962-E262-12 Provided by IHSNot for ResaleNo reproduction or

4、networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93154 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and

5、 MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 931

6、54 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 s

7、pecified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function Access time 01 WE-128K8-200CQ EEPROM, 128K x 8-bit 200 ns

8、 02 WE-128K8-150CQ EEPROM, 128K x 8-bit 150 ns 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,

9、 and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in a

10、pplications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer

11、guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition documen

12、t; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature

13、 range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93154 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as d

14、esignated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 32 Dual-in-line, dual cavity 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) -0.6 V dc to +6.2

15、5 V dc Input voltage range -0.6 V dc to +6.25 V dc Power dissipation (PD) . 1.0 W Storage temperature range -65 C to +150 C Lead temperature (soldering, 10 seconds) +300 C Thermal resistance junction-to-case (qJC) 28 C/W Data retention 10 years minimum 1.4 Recommended operating conditions. Supply vo

16、ltage range (VCC) . +4.5 V dc to +5.5 V dc Input low voltage range (VIL) . -0.3 V dc to +0.8 V dc Input high voltage range (VIH) +2.2 V dc to VCC+ 0.3 V dc Output voltage, high minimum (VOH) . +2.4 V dc Output voltage, low maximum (VOL) +0.45 V dc Case operating temperature range (TC) -55 C to +125

17、C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contrac

18、t. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK

19、-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of pr

20、ecedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolut

21、e maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93154 DLA L

22、AND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include th

23、e performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PR

24、F-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be

25、as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table(s). The truth table(s) shall be as specified on figure

26、 3. 3.2.4 Timing diagram(s). The timing diagram(s) shall be as specified on figures 4, 5, 6, and 7. 3.2.5 Block diagram. The block diagram shall be as specified on figure 8. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

27、as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marki

28、ng of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the devic

29、e described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed

30、. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to t

31、his drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shal

32、l be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan s

33、hall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93154 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 AP

34、R 97 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition D or E. The test circuit shall be maintained by the manufacturer under document revision level control and shall be

35、made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance w

36、ith table I of method 1015 of MIL-STD-883. (3) Prior to burn-in all devices shall be programmed with a 00 hex data pattern to the entire memory array. The resulting pattern shall be verified before and after burn-in. Devices having bits not in the proper state after burn-in shall constitute a device

37、 failure and shall not be delivered. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking per

38、mitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93154 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55 C TC +125 C VSS= 0 V dc +4.5 V dc VCC +5.5

39、 V dc unless otherwise specified Group A subgroups Device type Limits Unit Min Max DC PARAMETERS Supply current ICCCS = OE = VIL, WE = VIH, I/O 0 through I/O 7 = open, inputs = VCC= +5.5 V dc, A0 through A16 change at 5 MHz 1,2,3 01,02 90 mA Standby current ISB CS = VCC, I/O 0 through I/O 7 = open,

40、inputs = VCC= +5.5 V dc, A0 through A16 change at 5 MHz 1,2,3 01,02 5 mA Input leakage current ILIVIN= VSSto VCC1,2,3 01,02 20 mA Output leakage current ILOVOUT= VSSto VCC, CS = VIH1,2,3 01,02 20 mA Input low voltage VIL1,2,3 01,02 0.8 V Input high voltage VIH1,2,3 01,02 2.0 V Output low voltage VOL

41、IOL= +2.1 mA, VCC= +4.5 V 1,2,3 01,02 0.45 V Output high voltage VOHIOH= -400 mA, VCC= +4.5 V 1,2,3 01,02 2.4 V FUNCTIONAL TESTING Functional tests See 4.3.1c 7,8A,8B 01,02 DYNAMIC CHARACTERISTICS Input capacitance CINVIN= 0 V dc 2/ 4 01,02 45 pF Output capacitance COUTVOUT= 0 V dc 2/ 4 01,02 60 pF

42、See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93154 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performa

43、nce characteristics - Continued. Test Symbol Conditions 1/ -55 C TC +125 C VSS= 0 V dc +4.5 V dc VCC +5.5 V dc unless otherwise specified Group A subgroups Device type Limits Unit Min Max READ CYCLE AC TIMING CHARACTERISTICS Read cycle time tRCSee figure 4. 9,10,11 01 02 200 150 ns Address access ti

44、me tACCSee figure 4. 9,10,11 01 02 200 150 ns Chip select access time tACSSee figure 4. 9,10,11 01 02 200 150 ns Output hold from address change OE or CS tOHSee figure 4. 9,10,11 01,02 10 ns Output enable to output valid tOESee figure 4. 9,10,11 01 02 100 85 ns BYTE WRITE AC TIMING CHARACTERISTICS A

45、ddress setup time tASSee figure 5. 9,10,11 01,02 30 ns Write pulse width tWPSee figure 5. 9,10,11 01 02 200 150 ns Chip select setup time tCSSee figure 5. 9,10,11 01,02 0 ns Address hold time tAHSee figure 5. 3/ 9,10,11 01,02 50 ns Data valid to end of write tDVSee figure 5. 9,10,11 01,02 70 ns Outp

46、ut enable setup time tOESSee figure 5. 9,10,11 01,02 30 ns Data hold time tDHSee figure 5. 9,10,11 01,02 0 ns Output enable hold time tOEHSee figure 5. 9,10,11 01,02 0 ns Chip select hold time tCSHSee figure 5. 9,10,11 01,02 0 ns Write pulse width high tWPHSee figure 5. 9,10,11 01,02 50 ns See footn

47、otes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93154 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance chara

48、cteristics - Continued. Test Symbol Conditions 1/ -55 C TC +125 C VSS= 0 V dc +4.5 V dc VCC +5.5 V dc unless otherwise specified Group A subgroups Device type Limits Unit Min Max PAGE MODE WRITE AC TIMING CHARACTERISTICS Data setup time tDSSee figure 6. 9,10,11 01,02 100 ns Data hold time tDHSee figure 6. 9,10,11 01,02 10 ns Write pulse width tWPSee figure 6. 9,10,11 01 02 200 150 ns Byte load cycle time tBLCSee figure 6. 9,10,11 01,02 150 ms Write pulse wid