1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R248-94 94-07-22 M. A. FRYE B Changes in accordance with NOR 5962-R263-94 94-08-25 M. A. FRYE C Replaced reference to MIL-STD-973 with reference to MIL-PRF-38535. Drawing updated to reflect current requirements
2、. Redrawn. -rrp 04-05-13 R. MONNIN REV SHET REV SHET REV STATUS REV C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Sandra B. Rooney DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Sandra B. Rooney COLUMBUS, OHIO 43216 http:/www.dscc.dla.mil
3、 THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, CMOS VIDEO MULTIPLEXER/AMPLIFIER, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-02-17 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-94512 SHEET 1 OF
4、 11 DSCC FORM 2233 APR 97 5962-E266-04 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94512 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.
5、1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a ch
6、oice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 94512 01 M C X Federal stock class designator RHA designator (see 1.2.1) Devicetype (see 1.2.2) Device class designator Caseoutline (see 1.2.4) Lead finish (see 1
7、.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marke
8、d with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 MAX453 CMOS video 2-channel multiplexer/amplifier. 02 MAX455 CMOS video 8-channel multiplexe
9、r/amplifier. 03 MAX452 CMOS video amplifier. 04 MAX454 CMOS video 4-channel multiplexer/amplifier. 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certificat
10、ion to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Desc
11、riptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line P GDIP1-T8 or CDIP2-T8 8 Dual-in-line R GDIP1-T20 or CDIP2-T20 20 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and
12、V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94512 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97
13、 1.3 Absolute maximum ratings. 1/ Total supply voltage (V+ to V-) 12 V Positive supply voltage (V+) . +12 V Negative supply voltage (V-) -12 V Analog input voltage . (V+) + 0.3 V to (V-) - 0.3 V Digital input voltage -0.3 V to (V+) + 0.3 V Lead temperature (soldering, 10 seconds) . 300C Thermal resi
14、stance, junction-to-case (JC) See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case outline C . 110C/W Case outline P . 125C/W Case outline R . 90C/W Case outline 2 . 110C/W Storage temperature range -65C to +160C Duration of output short circuit to ground . Indefinite Input current, p
15、ower on or off: Digital inputs 20 mA All other pins . 50 mA Power dissipation at TA= 70C (PD): 2/ Case C 760 mW Case P 640 mW Case R . 890 mW Case 2 . 727 mW 1.4 Recommended operating conditions. Input voltage range . -2 V dc to +2 V dc Operating supply voltage . 4.5 V dc to 5.5 V dc Ambient operati
16、ng temperature range -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cit
17、ed in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE SPECIFICATION MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Out
18、lines. DEPARTMENT OF DEFENSE SPECIFICATION MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order
19、 Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Above TA= 70C, derate 9.5 mW/C for case C, derate
20、8 mW/C for case P, derate 11.1 mW/C for case R, and derate 9.09 mW/C for case 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94512 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C
21、 SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption ha
22、s been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not aff
23、ect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and ph
24、ysical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as
25、 specified on figure 1. 3.2.3 Channel selection. The channel selection shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limit
26、s are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall
27、 be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this
28、option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V sha
29、ll be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to
30、 supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to
31、listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A cert
32、ificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of
33、change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility
34、 and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 82 (see MIL-PRF-38535, appendix A)
35、.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94512 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics.
36、Limits Test Symbol Conditions -55C TA +125C unless otherwise specified -2 V VIN +2 V V+ = +5 V, V- = -5 V Group A subgroups Device type Min Max Unit VIDEO AMPLIFIER Input voltage range VIN1, 2, 3 All -2.0 2.0 V 1 5.0 Input offset voltage VOS2, 3 All 10.0 mV 1 10 Input bias current IB1/ 2, 3 All 500
37、nA RL= 1000 180 RL= 150 45 Open loop voltage gain AVOLRL= 75 4 All 25 V/V Common mode rejection ratio CMRR -2 V VIN +2 V 1 All 60 dB 1 54 Power supply rejection ratio PSRR 4.5 V to 5.5 V 2, 3 All 48 dB Slew rate SR 2/ 4 All 150 V/s GBW1 AV= 0 dB, RL= 75 2/ 30 -3 dB bandwidth GBW2 AV= 6 dB, RL= 150 2
38、/ 4 All 25 MHz Full scale output current IOUTRL= 150 1 All 14 mA Output voltage swing VOUTRL= 150 1 All 2.1 V Input noise, dc to 40 MHz VN2/ 1 All 0.5 mV Operating supply voltage V+, V- 1, 2, 3 All 4.5 5.5 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking pe
39、rmitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94512 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions -55C TA +125C unless
40、 otherwise specified -2 V VIN +2 V V+ = +5 V, V- = -5 V Group A subgroups Device type Min Max Unit 1 20 30 Supply current ICCVIN= 0 V 2, 3 All 17 32 mA MULTIPLEXER Input voltage range VIN1, 2, 3 01, 02, 04 -2.0 +2.0 V 1 10 OFF input leakage current IOFF3/ 2, 3 01, 02, 04 500 mA Logic low threshold V
41、IL1, 2, 3 01, 02, 04 0.8 V Logic high threshold VIH1, 2, 3 01, 02, 04 2.4 V Input pullup/down current IIL/IH1 01, 02, 04 20 A Turn-ON time tON2/ 9 01, 02, 04 120 ns Turn-OFF time tOFF2/ 9 01, 02, 04 60 ns Break-before-make delay tD2/ 9 01, 02, 04 10 ns Channel “ON“ capacitance CON2/ 4 01, 02, 04 15
42、pF Channel “OFF“ capacitance COFF2/ 4 01, 02, 04 12 pF fIN= 4 MHz, RS= 75 2/ Channel 2 to Channel 3 45 Channel “OFF“ isolation OIRR fIN= 4 MHz, RS= 75 2/ All other Channels 4 01, 02, 04 60 dB 1/ Input bias includes the multiplexers ON state leakage current. 2/ Guaranteed by design and not tested. 3/
43、 Guaranteed over voltage range, V- VIN V+. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94512 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Device
44、type 01 02 03 04 Case outline P 2 R and 2 P 2 C 2 Terminal number Terminal connection 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 A0 GND V- IN0 IN1 V+ IN- VOUT- - - - - - - - - - - - NC A0 NC NC GND NC V- NC NC NC IN0 NC NC IN1 NC V+ NC IN- NC VOUTA2 A1 A0 GND IN0 V- IN1 NC IN2 IN3 IN4 NC IN5
45、 NC IN6 NC IN7 V+ IN- VOUTNC NC V- NC IN+ V+ IN- VOUT- - - - - - - - - - - - NC NC NC NC NC V- NC NC NC IN+ NC NC NC NC NC V+ NC IN- NC VOUTA1 A0 GND V- NC NC IN0 IN1 NC IN2 IN3 V+ IN- VOUT- - - - - - NC A1 A0 NC GND NC V- NC NC IN0 NC IN1 NC IN2 NC IN3 V+ IN- NC VOUTFIGURE 1. Terminal connections.
46、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94512 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Device type 01 A0 Channel L H 0* 1 Device type 02
47、A2 A1 A0 Channel L L L L H H H H L L H H L L H H L H L H L H L H 0 1 2 3 4* 5 6 7 Device type 04 A1 A0 Channel L L H H L H L H 0* 1 2 3 * Default channel if selection pins are left floating. FIGURE 2. Channel selection. Provided by IHSNot for ResaleNo reproduction or networking permitted without lic
48、ense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94512 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufactu
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1