DLA SMD-5962-94603 REV A-2009 MICROCIRCUIT LINEAR HIGH OUTPUT CURRENT HIGH FREQUENCY CURRENT FEEDBACK AMPLIFIER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update boilerplate paragraphs to current MIL-PRF-38535 requirements. - ro 09-12-10 C. SAFFLE REV SHET REV SHET REV STATUS REV A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY RICK C. OFFICER DEFENSE SUPPLY C

2、ENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH R. PITHADIA APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, HIGH OUTPUT CURRENT, HIGH FREQU

3、ENCY CURRENT FEEDBACK AMPLIFIER, MONOLITHIC SILICON DRAWING APPROVAL DATE 94-05-16 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-94603 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E064-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD M

4、ICROCIRCUIT DRAWING SIZE A 5962-94603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (d

5、evice class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 94603 01 M

6、 C A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and

7、are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function

8、as follows: Device type Generic number Circuit function 01 LM6182A High output current, high frequency current feedback amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documen

9、tation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and

10、as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual in line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduct

11、ion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) 18 V Input voltage (VIN) VCCInverting

12、 input current . 15 mA Output current (IOUT) 2/ Differential input voltage . 6 V Maximum power dissipation (PD) 1.5 W Lead temperature (soldering, 10 seconds) +260C Junction temperature (TJ) . +150C Storage temperature range . -65C to +150C Thermal resistance, junction-to-case (JC) . 4.6C/W at 2.3 W

13、 Thermal resistance, junction-to-ambient (JA) 84C/W at 0.5 W, no air flow 44C/W at 0.5 W, 500 LFPM air flow 1.4 Recommended operating conditions. Supply voltage range (VCC) 7.0 V to 32 V Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, st

14、andards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Int

15、egrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. M

16、IL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict

17、 between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permane

18、nt damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of +150C. Each amplifier of the device is short cir

19、cuit current limited to 100 mA normally. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 3. REQUIR

20、EMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or func

21、tion as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be

22、 as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3

23、Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrica

24、l test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packa

25、ges where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance wi

26、th MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as re

27、quired in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of complianc

28、e shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, fo

29、r device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PR

30、F-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that

31、affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option o

32、f the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 049 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD

33、MICROCIRCUIT DRAWING SIZE A 5962-94603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA+125C Group A subgroups Device type Limits 2/ Unit unless otherwise specifi

34、ed Min Max Input offset voltage VOSVCC= 15 V, RL= 1 k 1 01 3.0 mV 2,3 4.0VCC= 5 V, RL= 1 k 1 2.0 2,3 3.0Input bias current -IIBVCC= 15 V, RL= 1 k 1 01 5.0 A 2,3 12.0VCC= 5 V, RL= 1 k 1 10.0 2,3 22.0+IIBVCC= 15 V, RL= 1 k 1 2.0 2,3 4.0VCC= 5 V, RL= 1 k 1 1.5 2,3 3.0Input bias current power supply rej

35、ection -IIBVCC= 4.5 V to 16 V 1 01 0.5 A / V PSRR 2,3 3.0 VCC= 5 V, RL= 1 k, 1 0.5 VCC= 4.0 V to 6 V 2,3 1.0 +IIBVCC= 4.5 V to 16 V 1 0.5 PSRR 2,3 1.5VCC= 5 V, RL= 1 k, 1 0.5 VCC= 4.0 V to 6 V 2,3 1.0 Input bias current common mode rejection -IIBVCM= -10 V to +10 V 1 01 0.5 A / V CMRR 2,3 1.0 VCC= 5

36、 V, RL= 1 k, 1 0.5 VCM= -2.5 V to +2.5 V 2,3 1.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A

37、SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA+125C Group A subgroups Device type Limits 2/ Unit unless otherwise specified Min Max Input bias current common mode rejection +IIBVCM= -10 V to +10 V 1 01 0.5 A / V CMRR 2,3 1.0

38、 VCC= 5 V, RL= 1 k, 1 0.5 VCM= -2.5 V to +2.5 V 2,3 1.0 Common mode rejection ratio CMRR VCM= -10 V to +10 V 1 01 50.0 dB 2,3 47.0VCC= 5 V, RL= 1 k, 1 50.0 VCM= -2.5 V to +2.5 V 2,3 47.0 Power supply rejection ratio PSRR VCC= 4.5 V to 16 V 1 01 70.0 dB 2,3 67.0VCC= 5 V, RL= 1 k, 1 70.0 VCC= 4.0 V to

39、 6.0 V 2,3 67.0 Non-inverting input resistance RIN1,2,3 01 1.0 M VCC= 5 V, RL= 1 k 0.5 Output current 3/ ISCVOUTto rail, 1 01 70.0 mA RL= 10 to GND 2,3 37.5 VCC= 5 V, RL= 1 k, 1 65.0 RL= 10 to GND, VOUTto rail 2,3 35.0 Transimpedance ZtRL= 1 k 1 01 1.0 M 2,3 0.4RL= 150 1 0.8 2,3 0.3VCC= 5 V, RL= 1 k

40、 1 0.75 2,3 0.3See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 TABL

41、E I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA+125C Group A subgroups Device type Limits 2/ Unit unless otherwise specified Min Max Transimpedance ZtVCC= 5 V, RL= 150 1 01 0.5 M 2,3 0.2Supply current ICCNo load, VIN= 0 V 1 01 20.0 mA 2,3 22.0VCC= 5 V, RL= 1

42、k, 1 17.0 no load, VIN= 0 V 2,3 18.5 Output voltage swing VOPRL= 1 k 4 01 11.0 V 5,6 10.0RL= 150 4 9.5 5,6 5.6VCC= 5 V, RL= 1 k 4 2.25 5,6 2.00VCC= 5 V, RL= 150 4 2.0 5,6 1.8Gain AVOLRL= 1 k 4,5,6 01 50 dB RL= 150 4,5,6 15 VCC= 5 V, RL= 1 k 4 30 5,6 7.5VCC= 5 V, RL= 150 4 7.5 5,6 5.0Input common mod

43、e 4/ voltage range VCM4,5,6 01 -10 10 V VCC= 5 V -2.5 2.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION

44、 LEVEL A SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA+125C Group A subgroups Device type Limits 2/ Unit unless otherwise specified Min Max Closed loop bandwidth -3 dB BW AVS= -1 4 01 75 MHz 5,6 65AVS= -10 4,5,6 35 VCC= 5 V

45、, AVS= -1 4,5,6 30 VCC= 5 V, AVS= -10 4,5,6 20 Slew rate 5/ SR AVS= -1, VOUT= 10 V, RL= 150 4,5,6 01 1000 V/s VCC= 5 V, AVS= -1, 4 375 VOUT= 2 V, RL= 150 5,6 300 Settling time at 0.1 % tSAVS= -1, VOUT= 5 V, 9 01 85 ns RL= 150 10,11 115 VCC= 5 V, AVS= -1, 9 85 VOUT= 2 V, RL= 150 10,11 125 1/ Unless o

46、therwise specified, VCC= 15 V and RL= 1 k. 2/ The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as conventional current flow out of a device terminal. 3/ Continuous short circuit operati

47、on at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150C. Each amplifier of the device is short circuit limited to 100 mA normally. 4/ Guaranteed by CMRR test. 5/ Measured from +25% point to +75% of output waveform. Provided by IHSNot for ResaleNo r

48、eproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 Device type 01 Case outline C Terminal number Terminal symbol 1 NC2 -INPUT A 3 +INPUT A 4 -VCC5 +INPUT B 6 -INPUT B 7 NC8 NC 9 OUTPUT B10 NC 11 +VCC12 NC