1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02. Make changes to 1.2.2 and to the noise test as specified in table I. - ro 01-02-02 R. MONNIN B Drawing updated to reflect current requirements. - ro 06-04-03 R. MONNIN REV SHET REV SHET REV STATUS REV B B B B B B B B B OF SHEE
2、TS SHEET 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY MARCIA B. KELLEHER DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY RAJESH PITHADIA COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHAEL A. FRYE AND AGENCIES OF
3、 THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-06-14 MICROCIRCUIT, LINEAR, +10 V VOLTAGE REFERENCE , MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-94681 SHEET 1 OF 9 DSCC FORM 2233 APR 97 5962-E127-06 Provided by IHSNot for ResaleNo reproduction or networking permitte
4、d without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94681 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device
5、classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in
6、 the following example: 5962 - 94681 01 M G X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet t
7、he MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The dev
8、ice type(s) identify the circuit function as follows: Device type Generic number Circuit function Noise 01 MAX674 +10 V voltage reference 30 VPP02 MAX674 +10 V voltage reference 150 VPP1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance lev
9、el as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The
10、 case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style G MACY1-X8 8 Can P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for
11、device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94681 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3
12、DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VIN) 40 V Output short-current duration (to GND or VIN) Indefinite Power dissipation (PD), (TA= +70C): Case outline G . 533 mW 2/ Case outline P . 640 mW 3/ Case outline 2 727 mW 4/ Storage temperature range . -65C to +150C Lead
13、temperature (soldering, 10 seconds) 300C Junction temperature (TJ) . +150C Thermal resistance, junction-to-case (JC): Case outline G . 45C/W Case outline P . 55C/W Case outline 2 See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case outline G . 150C/W Case outline P . 125C/W Case outli
14、ne 2 110C/W 1.4 Recommended operating conditions. Input voltage range (VS) . 2.0 V to 16.5 V Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of t
15、his drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MI
16、L-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online
17、at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the m
18、aximum levels may degrade performance and affect reliability. 2/ Derate at 6.67 mW/C for TAabove 70C. 3/ Derate at 8.00 mW/C for TAabove 70C. 4/ Derate at 9.09 mW/C for TAabove 70C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUI
19、T DRAWING SIZE A 5962-94681 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing
20、 in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in
21、 the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as
22、specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall
23、 be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiat
24、ion parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Mark
25、ing. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA
26、product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device
27、classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manuf
28、acturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted t
29、o DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of
30、conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notifica
31、tion to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the man
32、ufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 59 (see MIL-PRF
33、-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94681 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performan
34、ce characteristics. Test Symbol Conditions -55C TA +125C VIN= +15.0 V Group A subgroups Device type Limits 1/ Unit unless otherwise specified Min Max Output voltage tolerance VOTIL= 0 mA 1,2,3 All -15 +15 mV Output adjustment range VTRIMRP = 10, TA= +25C 1 All -300 +300 mV Line regulation VRLINEVIN=
35、 13 V to 33 V 2/ 1 All 0.01 %/V 2,3 0.02 Load regulation VRLOADIL= 0 mA to 10 mA 2/ 1 All 0.002 %/mA 2,3 0.004 Quiescent supply current IQNo load 1 All 1400 A 2,3 2000 Sink current ISTA= +25C 1 All -0.3 mA Load current IL3/ 1 All 10 mA 2,3 8 Short-circuit ISCVO= 0 V, TA= +25C 1 All 40 mA Noise 4/ 0.
36、1 MHz to 10 MHz, 4 01 30 VPPTA= +25C 02 150 Output voltage change with temperature TCVO 4,5,6 All 20 ppm/C 1/ The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum is used in this table. Negative current shall be defined as conventional current flow o
37、ut of a device terminal. 2/ Line and load regulation specifications include the effect of self heating. 3/ Minimum load current is guaranteed by load regulation test. 4/ Noise is sample tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD
38、 MICROCIRCUIT DRAWING SIZE A 5962-94681 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 Device type 01 Case outlines G and P 2 Terminal number Terminal symbol 1 NC NC 2 VINNC 3 NC NC 4 GND NC 5 TRIM VIN6 VOUTNC 7 NC NC 8 NC NC 9 - NC 10 - GND 1
39、1 - NC 12 - TRIM 13 - NC 14 - NC 15 - VOUT16 - NC 17 - NC 18 - NC 19 - NC 20 - NC NC = No connection FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94681 DEFENSE SUPPLY CENTER
40、 COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturers Quality Management (QM)
41、plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PR
42、F-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. 4.2.1 Additional criteria
43、for device class M. a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition B. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the in
44、puts, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein. 4.2.2 Additional criteria for device classes Q and V. a. The burn-in
45、test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturers QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under document revision level control of the device manufacturers Technology Review Bo
46、ard (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. b. Inte
47、rim and final electrical test parameters shall be as specified in table II herein. c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in MIL-PRF-38535, appendix B. 4.3 Qualification inspection for device classes Q and V. Qualification inspectio
48、n for device classes Q and V shall be in accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with MIL-PRF-38535 including groups A, B, C, D, and E inspections and as specified herein. Quality conformance inspection for device class M shall be in accordance with MIL-PRF-38535, appendix A and as specifi
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1