DLA SMD-5962-94694 REV C-2009 MICROCIRCUIT LINEAR WIDEBAND HIGH SLEW RATE VIDEO OPERATIONAL AMPLIFIER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Make changes to the Large signal voltage gain test under Table I in accordance with N.O.R. 5962-R180-96. 96-07-10 M. A. FRYE B Drawing updated to reflect current requirements. Redrawn. - ro 02-03-04 R. MONNIN C Make correction to the -CMRR subgro

2、ups 2 and 3 test limit as specified under Table I. - ro 09-03-02 R. HEBER REV SHET REV SHET REV STATUS REV C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK C. OFFICER CHECKED BY RAJESH R. PITHADIA DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/w

3、ww.dscc.dla.mil APPROVED BY MICHAEL A. FRYE STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-07-13 MICROCIRCUIT, LINEAR, WIDEBAND, HIGH SLEW RATE, VIDEO OPERATIONAL AMPLIFIER, MONOLITHIC SILICON AMSC

4、 N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-94694 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E195-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 432

5、18-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are refle

6、cted in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 94694 01 M P A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)D

7、evice class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet

8、 the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 HA-2842 Wideband, high slew

9、 rate, video operational amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class

10、 level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style P GDIP1-T8 or CDIP2-T

11、8 8 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962

12、-94694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Voltage between +VSand -VSterminals . +35 V Differential input voltage (VIND) . 6 V Voltage at either input terminal +VSto -VSPeak output current ( 40% duty

13、 cycle ) . 125 mA Power dissipation (PD) 0.9 W at TA= +75C 2/ Junction temperature (TJ) +175C Storage temperature range -65C to +150C Lead temperature range (soldering 10 seconds) . +300C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) . +110C/

14、W 1.4 Recommended operating conditions. Supply voltage (VS) . 12 V to 15 V Common mode input voltage (VINCM) . 1/2 x (+VS- -VS) Load resistance (RL) 1 k Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The follow

15、ing specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, G

16、eneral Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircui

17、t Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing a

18、nd the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended o

19、peration at the maximum levels may degrade performance and affect reliability. 2/ Derating factor above TA= +75C is 9 mW/C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94694 DEFENSE SUPPLY CENTER COLUMBUS

20、 COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management

21、 (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction,

22、and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Ter

23、minal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table

24、 I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN lis

25、ted in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator

26、shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as req

27、uired in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements

28、 of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved sour

29、ce of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as r

30、equired for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2

31、herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required do

32、cumentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 49 (see MIL-PRF-38535, appendix A). Provided by IHSNot for Re

33、saleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/

34、-55C TA+125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Input offset voltage VIOVCM= 0 V 1 01 -4 +4 mV 2,3 -8 +8Input bias current IIBVCM= 0 V, +RS= 1.1 k, 1 01 -10 10 A -RS= 100 2,3 -20 20 VCM= 0 V, +RS= 100 , 1 -10 10 -RS= 1.1 k 2,3 -20 20 Input offset current

35、IIOVCM= 0 V, +RS= 1.1 k, 1 01 -1 +1 A -RS= 1.1 k 2,3 -2 +2 +VCMR+VS= +5 V, -VS= -25 V 1 01 10 V Common mode voltage range 2,3 10 -VCMR+VS= +25 V, -VS= -5 V 1 -10 2,3 -10 Common mode rejection ratio +CMRR VCM= 10 V, VOUT= -10 V, 1 01 90 dB +VS= +5 V, -VS= -25 V 2,3 85 -CMRR VCM= -10 V, VOUT= 10 V, 1

36、90 +VS= +25 V, -VS= -5 V 2,3 85 Output voltage swing +VOUTRL= 1 k 1,2,3 01 10 V -VOUT-10 Output current +IOUTVOUT= -5 V 3/ 1,2,3 01 100 mA -IOUTVOUT= +5 V 3/ -100 +ICCVOUT= 0 V, IOUT= 0 mA 1,2,3 01 15 mA Quiescent power supply current -ICC-15 See footnotes at end of table. Provided by IHSNot for Res

37、aleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Condi

38、tions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Power supply rejection ratio +PSRR VS= 10 V, +V = 10 V and -V = -15 V, +V = 20 V and -V = -15 V 1,2,3 01 70 dB -PSRR VS= 10 V, +V = 15 V and -V = -10 V, +V = 15 V and -V = -20 V 70 Offset voltage ad

39、justment +VIOTA= +25C 4/ 1 01 VIO-1 mV -VIOVIO+1 Large signal voltage gain +AVOLVOUT= 0 V and +10 V, 4 01 50 kV / V RL= 1 k 5 30 6 5 -AVOLVOUT= 0 V and -10 V, 4 50 RL= 1 k 5 30 6 5 Gain bandwidth 5/ 6/ product GBWP VOUT= 200 mV, fO= 100 kHz, TA= +25C 4 01 60 MHz VOUT= 200 mV, fO= 10 MHz, TA= +25C 70

40、 Slew rate 5/ 6/ 7/ +SR VOUT= -5.0 V to +5.0 V, 4,6 01 350 V/s RL= 1 k, AV= 10 V/V 5 300 -SR VOUT= +5.0 V to -5.0 V, 4,6 350 RL= 1 k, AV= 10 V/V 5 300 FPBW VPK= +10 V 7/ 4,6 01 5.5 MHz Full power 5/ 6/ 8/ bandwidth 5 4.7 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or

41、networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA+125C

42、unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Minimum closed 5/ 6/ loop stable gain CLSG VOUT= 0 V, CL 10 pF 4,5,6 01 2 V/V Overshoot 5/ 6/ +OS VOUT= 0 V to +200 mV 4 01 50 % 5,6 55 -OS VOUT= 0 V to -200 mV 4 50 5,6 55 Rise time 5/ 6/ 7/ tRVOUT= 0 V to +200 mV, 9 01

43、 5 ns CL 10 pF 10,11 7 Fall time 5/ 6/ 7/ tFVOUT= 0 V to -200 mV, CL 10 pF 9,10,11 01 5 ns 1/ Unless otherwise specified, supply voltage (VS) = 15 V, source resistance (RS) = 100 , load resistance (RL) = 100 k, and output voltage (VOUT) = 0 V. 2/ The algebraic convention, whereby the most negative v

44、alue is a minimum and the most positive value is a maximum, is used in this table. Negative current shall be defined as conventional current flow out of a device terminal. 3/ Maximum power dissipation, including output load conditions, must be designed to maintain the maximum junction temperature be

45、low +175C. For a 100 mA load and a temperature of +125C ambient, heat sinking is required. 4/ Offset voltage adjustment range is VIO(measured) 1 mV minimum referred to output. This test is for functionality only, to assure adjustment through 0 V. 5/ If not tested, shall be guaranteed to the limits s

46、pecified in table I herein. 6/ Supply voltage (VS) = 15 V, source resistance (RS) = 50 , load resistance (RL) = 1 k, and gain (AV) = +2 V/V. 7/ Measured at 10 percent to 90 percent points. 8/ Full bandwidth is based on slew rate measurement based using FPBW = slew rate / (2 x x VPK). Provided by IHS

47、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outline P Terminal number Terminal symbol 1 B

48、ALANCE 2 -INPUT 3 +INPUT4 -VS5 NC 6 OUTPUT 7 +VS8 BALANCE FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampli