DLA SMD-5962-95641 REV A-2011 MICROCIRCUIT LINEAR 23 MHZ DUAL PRECISION OPERATIONAL AMPLIFIER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update boilerplate paragraphs to current MIL-PRF-38535 requirements. - ro 11-04-05 C. SAFFLE REV SHET REV SHET REV STATUS REV A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND M

2、ARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH PITHADIA APPROVED BY MICHAEL FRYE MICROCIRCUIT, LINEAR, 23 MHZ, DUAL PRECISION OPERATIONAL AMPLIFIER

3、, MONOLITHIC SILICON DRAWING APPROVAL DATE 95-06-20 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-95641 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E199-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962

4、-95641 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outline

5、s and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 95641 01 M P A Federal stock class designator RHA

6、designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA desi

7、gnator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number C

8、ircuit function 01 LT1215 25 MHz, dual precision operational amplifier 02 LT1215A 25 MHz, dual precision operational amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentat

9、ion M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as

10、follows: Outline letter Descriptive designator Terminals Package style P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or

11、 networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95641 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Total supply voltage ( +VSto -VS) . 36 V Input current (IIN) 15 mA Output

12、 short circuit duration Continuous 2/ Power dissipation (PD) 1.25 W Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) . +150C Storage temperature range . -65C to +150C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) 100

13、C/W 1.4 Recommended operating conditions. Supply voltage ( +VSto -VS) 3.3 V, 5 V, 15 V Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this dr

14、awing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-

15、883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at htt

16、ps:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes pr

17、ecedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect

18、 reliability. 2/ A heat sink may be required to keep the junction temperature below absolute maximum when the output is shorted indefinitely. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95641 DLA LAND AND

19、 MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality M

20、anagement (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, const

21、ruction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein.

22、3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified

23、 in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with th

24、e PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designato

25、r shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as r

26、equired in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requiremen

27、ts of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing

28、as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate

29、of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Mariti

30、me -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the

31、 option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit gro

32、up number 49 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95641 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Elec

33、trical performance characteristics. Test Symbol Conditions -55C TA+125C Group A subgroups Device type Limits Unit unless otherwise specified Min Max VS= 3.3 V 1/ Input offset voltage VOS1 01 450 V 02 3002,3 01 750 02 350Input voltage range VIN2/ 1 01,02 1.3 to 0 V 2,31.1 to 0.4 Maximum output voltag

34、e swing VOUTOutput high, no load 1 01,02 2.6 V 2,3 2.3Output high, 1 2.5 ISOURCE= 1 mA 2,3 2.2 Output high, ISOURCE= 30 mA 1 1.9 Output high, ISOURCE= 20 mA 2,3 1.9 Output low, no load 1 0.08 2,3 0.012Output low, ISINK= 1 mA 1 0.05 2,3 0.07Output low, ISINK= 30 mA 1 1.0 Output low, ISINK= 20 mA 2,3

35、1.0 Maximum output current IOUTTA= +25C 1 01,02 30 mA VS= 5 V 1/ Input offset voltage VOS1 01 450 V 02 3002,3 01 750 02 450See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95641

36、DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TA+125C Group A subgroups Device type Limits Unit unless otherwise specified Min Max VS= 5 V - continued. 1/ Input o

37、ffset voltage drift VOS/ TA= +125C, -55C 3/ 2,3 01 5 V/C t 02 2.5Input offset current IOS1 01 120 nA 02 802,3 01 200 02 150Input bias current IIB1 01 600 nA 02 500 2,3 01 700 02 600Input resistance RINDifferential mode, 3/ TA= +25C 1 01,02 10 M Input voltage range VINR1 01,02 3 to 0 V 2,3 2.8 to 0.4

38、 Maximum output voltage 4/ swing VOUTOutput high, no load 1 01,02 4.3 V 2,3 4.0 Output high, 1 4.2ISOURCE= 1 mA 2,3 3.9 Output high, ISOURCE= 30 mA1 3.6 Output high, ISOURCE= 20 mA2,3 3.5 Output low, no load 1 0.008 2,3 0.012Output low, ISINK= 1 mA 1 0.05 2,3 0.07Output low, ISINK= 30 mA 1 1.0 Outpu

39、t low, ISINK= 20 mA 2,3 1.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95641 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97

40、TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TA+125C Group A subgroups Device type Limits Unit unless otherwise specified Min Max VS= 5 V - continued. 1/ Maximum output current IOUTTA= +25C 5/ 1 01,02 30 mA Supply current per amplifier IS1 01,02 3.6 6.6 mA

41、 2,3 2.3 8.4 Minimum supply voltage VSSingle supply, TA= +25C 1 01,02 2.5 V Common mode rejection mode CMRR VCM= 0 V to 3 V 4 01 86 dB 02 90VCM= 0.4 V to 2.8 V 5,6 01 82 02 87Power supply rejection ratio PSRR VS= 2.5 V to 12.5 V 4 01 93 dB 02 96VS= 2.7 V to 12.5 V 5,6 01 90 02 93Large signal voltage

42、 gain AVOLVOUT= 0.05 V to 3.7 V, RL= 500 4 01,02 150 V/mV VS= 15 V 6/ Input offset voltage VOS1 01 650 V 02 5002,3 01 950 02 650Input offset voltage drift VOS/ TA= +125C, -55C 3/ 2,3 01 5 V/C t 02 2.5 Input offset current IOS1 01 110 nA 02 802,3 01 200 02 150See footnotes at end of table. Provided b

43、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95641 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Sym

44、bol Conditions -55C TA+125C Group A subgroups Device type Limits Unit unless otherwise specified Min Max VS= 15 V - continued. 6/ Input bias current IIB1 01 550 nA 02 5002,3 01 700 02 600Input voltage range VINR1 01,0213 to -15 V 2,3 12.8 to -14.6 Supply current per amplifier IS1 01,02 3.6 8 mA 2,3

45、2.3 10.3 Minimum supply voltage VSEqual split supplies, TA= +25C 1 01,02 2.5 V Minimum output current IOUTTA= +25C 5/ 1 01,02 30 mA Maximum output voltage swing VOUTOutput high, ISOURCE= 30 mA1 01,02 13.5 V Output high, ISOURCE= 20 mA2,3 13.4 Output low, ISINK= 30 mA 1 -14 Output low, ISINK= 20 mA 2

46、,3 -14 Common mode rejection mode CMRR VCM= -15 V to 13 V 4 01 86 dB 02 90VCM= -14.6 V to 12.8 V 5,6 01 82 02 87Power supply rejection ratio PSRR VS= 2 V to 18 V 4 01 93 dB 02 96VS= 2.2 V to 15 V 5,6 01 90 02 93See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking

47、 permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95641 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TA+125C Group A subgroups De

48、vice type Limits Unit unless otherwise specified Min Max VS= 15 V - continued. 6/ Slew rate SR AV= -2, TA= +25C 7/ 4 01,02 40 V / s Gain bandwidth product GBW f = 100 kHz, TA= +25C 4 01,02 15 MHz Channel separation CS VOUT= 10 V, RL= 2 k, TA= +25C 4 01,02 128 dB Large signal voltage gain AVOLVOUT= 0 V to 10 V, 4 01,02 1000 V/mV RL= 2 k 5,6 500 1/ Unless otherwise specified, VCM= 0.5 V and VOUT= 0.5 V. 2/ Guaranteed to correlation to 5 V and 1