DLA SMD-5962-95796 REV B-2013 MICROCIRCUIT HYBRID LINEAR 12 VOLT DUAL CHANNEL DC DC CONVERTER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. -sld 04-12-13 Raymond Monnin B Corrected dimensions for symbols D, D2, and L1 for case outline U. Corrected dimensions for symbols D2, L, and L1 for case outline X. Corrected dimensions for symbols

2、 D, L, and L1 for case outline Y. Corrected dimensions for symbols D, D2, and L1 for case outline Z. Added footnote 1 to table II, under group C end-point electricals. Updated drawing paragraphs. -sld 13-07-18 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B B B B OF SHEETS

3、 SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve L. Duncan DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMEN

4、T OF DEFENSE APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, 12 VOLT, DUAL CHANNEL, DC/DC CONVERTER DRAWING APPROVAL DATE 98-12-17 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-95796 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E229-13 Provided by IHSNot for ResaleNo reproduction

5、or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95796 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3

6、and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 -

7、95796 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-3853

8、4 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 AFL2812D/CH DC/DC converter, 96 W, 12 V output 1.2.

9、3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product

10、 assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability device

11、s are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conforma

12、nce inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be revi

13、ewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction

14、 or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95796 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline le

15、tter Descriptive designator Terminals Package style U See figure 1 12 Y case configuration with leads bent upwards X See figure 1 12 Straight leads with end mounting thru holes Y See figure 1 12 Straight leads with side mounting thru holes Z See figure 1 12 Y case configuration with leads bent downw

16、ards 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage range -0.5 V dc to +50 V dc Lead temperature (soldering, 10 seconds) +300C Storage temperature range . -65C to +135C 1.4 Recommended operating conditions. Input voltage rang

17、e +16 V dc to +40 V dc Output power 2/ 3/ . 96 W Case operating temperature range -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless oth

18、erwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Inte

19、rface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Docume

20、nt Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws

21、 and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Derate output power linearly above case temperature +125

22、C to 0 at +135C. 3/ Output load must be distributed so that a minimum of 20% of the total output power is being provided by one of the outputs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95796 DLA LAND A

23、ND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the per

24、formance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-385

25、34 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as sp

26、ecified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2 3.3 Electrical performance characteristics. Unless otherwise specified herein,

27、the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defi

28、ned in table I. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.6 Data. In addition to the general performance requirements of

29、MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested,

30、 and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required

31、from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of con

32、formance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (Q

33、M) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95796 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990

34、REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC+125C VIN= 28 V dc 5%, CL= 0 unless otherwise specified Group A Subgroups Device type Limits Unit Min Max Output voltage VOUTIOUT= 4 A, both outputs 1 01 11.88 12.12 V 2,3 11

35、76 12.24 Output current 1/ IOUTVIN= 16, 28, 40 V dc, either output 1,2,3 01 6.4 A Output ripple voltage 2/ VRIPVIN= 16, 28, 40 V dc, B.W. = 10 MHz, IOUT= 4 A, both outputs 1,2,3 01 80 mV p-p Line regulation 3/ VRLINEVIN= 16, 28, 40 V dc, IOUT= 0, 2, and 4 A, both outputs 1,2,3 01 60 mV Load regulat

36、ion 3/ VRLOADVIN= 16, 28, 40 V dc, IOUT= 0, 2, and 4 A, both outputs 1,2,3 01 120 mV Cross regulation 4/ Positive output VRCROSVIN= 16, 28, 40 V dc 1,2,3 01 120 mV Negative output 600 Input current IINIOUT= no load 1 01 80 mA 2,3 100 Enable 1, (pin 4) shorted to Input return (pin 2) 1,2,3 5 Enable 2

37、 (pin 12) shorted to Output return (pin 8) 1,2,3 30 Input ripple current 2/ IRIPIOUT= 4 A, both outputs B.W. = 10 MHz 1,2,3 01 60 mA p-p Efficiency EFFIOUT = 4 A, both outputs 1,2,3 01 80 % Isolation ISO Input to output or any pin to case (except pin 3) at 500 V dc, TC=+25C 1 01 100 M See footnotes

38、 at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95796 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance character

39、istics - Continued. Test Symbol Conditions -55C TC+125C VIN= 28 V dc 5%, CL= 0 unless otherwise specified Group A Subgroups Device type Limits Unit Min Max Maximum Capacitive load 5/ CLEach output 4 01 10,000 F Power dissipation load fault PD Overload 6/ 1,2,3 01 33 W Short circuit 33 Current limit

40、point 7/ ICLVOUT= 90 % VNOMCurrent split equally on positive and negative outputs 1 01 4.6 5.0 A 2 4.2 4.6 3 5.0 5.6 Switching frequency FS4,5,6 01 500 600 kHz Sync frequency range FSYNC4,5,6 01 500 700 kHz Output response to step transient load changes 8/ VOTLOAD50% to/from 100% 4,5,6 01 -750 +750

41、mV pk 10% to/from 50% -750 +750 Recovery time, step transient load changes 8/ 9/ TTLOAD50% to/from 100% 4,5,6 01 200 s 10% to/from 50% 400 Output response to transient step line changes 5/ 10/ VOTLINEInput step, 16 V to/from 40 V dc 4,5,6 01 -500 +500 mV pk Recovery time transient step line changes

42、5/ 9/ 10/ TTLINEInput step, 16 V to/from 40 V dc 4,5,6 01 500 s Turn on overshoot VTonosEnable 1 and 2 on. (Pins 4 and 12 high or open) 4,5,6 01 250 mV pk See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCI

43、RCUIT DRAWING SIZE A 5962-95796 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC+125C VIN= 28 V dc 5%, CL= 0 unless otherwise specified Group A Subgroups Device t

44、ype Limits Unit Turn on delay 11/ TonDEnable 1 and 2 on. (Pins 4 and 12 high or open) 4,5,6 01 10 ms Load fault recovery 5/ TrLF4,5,6 01 10 ms 1/ Parameter guaranteed by line and load regulation tests. 2/ Bandwidth guaranteed by design. Tested for 20 kHz to 10 MHz. 3/ Load current split equally betw

45、een +VOUTand -VOUT. 4/ Cross regulation measured with load on tested output at 20 percent while changing the load on the other output from 20 percent to 80 percent. 5/ Parameter shall be tested as part of design characterization and after design or process changes. Thereafter, parameters shall be gu

46、aranteed to the limits specified in table I. 6/ An overload is that condition with a load in excess of the rated load but less than that necessary to trigger the short circuit protection and is the condition of maximum power dissipation. 7/ Current limit point is that condition of excess load causin

47、g output voltage to drop 90 percent of nominal. 8/ Load step transition time 10 microseconds. 9/ Recovery time is measured from the initiation of the transient to where VOUThas returned to within 1 percent of VOUTat 50 percent load. 10/ Input step transition time 100 microseconds. 11/ Turn on delay

48、is measured with an input voltage rise time of between 100 and 500 volts per millisecond. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95796 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Case U Millimeters Inches Symbol Min Max Min Max A 9.65 .380 D 70.35 71.96 2.770 2.8