DLA SMD-5962-96803 REV B-2011 MICROCIRCUIT DIGITAL ADVANCED HIGH SPEED CMOS HEX INVERTER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update the boilerplate paragraphs to the current MIL-PRF-38535 requirements. LTG 09-02-19 Charles F. Saffle B To change test condition of VCCmaximum voltage for VIHand VILto section 1.4. LTG 11-09-26 Thomas M. Hess REV SHET REV B B SHET 15 16 REV

2、 STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Rajesh Pithadia DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENC

3、IES OF THE DEPARTMENT OF DEFENSE AMSC N/A CHECKED BY Rajesh Pithadia APPROVED BY Raymond Monnin MICROCIRCUIT, DIGITAL, ADVANCED HIGH SPEED CMOS, HEX INVERTER, MONOLITHIC SILICON DRAWING APPROVAL DATE 96-06-28 REVISION LEVEL B SIZE A CAGE CODE 67268 5962-96803 SHEET 1 OF 16 DSCC FORM 2233 APR 97 5962

4、-E476-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96803 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two pro

5、duct assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (R

6、HA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 96803 01 Q C A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.

7、1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A

8、dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54AHCU04 Hex inverter 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance

9、 level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s).

10、 The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as spe

11、cified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96803 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISI

12、ON LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to +7.0 V dc 4/ DC output voltage range (VOUT) . -0.5 V dc to VCC+0.5 V dc 4/ DC input clamp current (IIK) (VINVCC) 20 mA Continuou

13、s output current (IO) (VO= 0 to VCC) . 25 mA Continuous current through VCCor GND 50 mA Storage temperature range (TSTG) . -65C to +150C Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C Maximum power dissipati

14、on at TA= +55C (in still air) (PD) . 500 mW 1.4 Recommended operating conditions. 2/ 3/ 5/ Supply voltage range (VCC) . +2.0 V dc to +5.5 V dc Input voltage range (VIN) . +0.0 V dc to 5.5 V dc Output voltage range (VOUT) +0.0 V dc to VCCCase operating temperature range (TC) -55C to +125C Minimum hig

15、h level input voltage (VIH): VCC= 2 V . +1.7 V VCC= 3 V . +2.4 V VCC= 5.5 V . +4.4 V Maximum low level input voltage (VIL): VCC= 2 V . +0.3 V VCC= 3 V . +0.6 V VCC= 5.5 V +1.1 V Maximum high level output current (IOH): VCC= 2 V . -50 A VCC= 3.3 V 0.3 V -4 mA VCC= 5.0 V 0.5 V -8 mA Maximum low level

16、output current (IOL): VCC= 2 V . +50 A VCC= 3.3 V 0.3 V +4 mA VCC= 5.0 V 0.5 V +8 mA 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltage

17、s are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. Unused inputs must be held high or low to prevent them from floating. 4/ The input and output voltage ratings may be exceeded provided

18、that the input and output current ratings are observed. 5/ Unused inputs must be held high or low to prevent them from floating. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96803 DLA LAND AND MARITIME COL

19、UMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issu

20、es of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standar

21、d Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document

22、Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws an

23、d regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) plan. The

24、modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dim

25、ensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connecti

26、ons. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce load circuit and waveforms. The ground bounce load circuit and waveform

27、s shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.2.7 Radiation exposure circuit. The radiation exposure circuit shall be as specified when available. 3.3 Electrical performance characteristi

28、cs and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. Provided by IHSNot for ResaleNo reproduction or netw

29、orking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96803 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II

30、. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manuf

31、acturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A

32、. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a

33、certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in M

34、IL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for dev

35、ice class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to

36、 this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device cl

37、ass M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcir

38、cuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 36 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 59

39、62-96803 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +2.0 V VCC +5.5 V unless otherwise specified VCCGroup A subgroups Limit

40、s 3/ Unit Min Max High level output voltage 3006 VOHFor all inputs affecting output under test VIN= VIHor VILFor all other inputs VIN= VCCor GND IOH= -50 A 2.0 V 1, 2, 3 1.8 V 3.0 V 2.7 4.5 V 4.0 IOH= -4 mA 3.0 V 1 2.58 2, 3 2.48 IOH= -8 mA 4.5 V 1 3.94 2, 3 3.8 Low level output voltage 3007 VOLFor

41、all inputs affecting output under test VIN= VIHor VILFor all other inputs VIN= VCCor GND IOL= 50 A 2.0 V 1, 2, 3 0.2 V 3.0 V 0.3 4.5 V 0.5 IOH= 4 mA 3.0 V 1 0.36 2, 3 0.5 IOL= 8 mA 4.5 V 1 0.36 2, 3 0.5 Input current high 3010 IIHFor input under test, VIN= VCCFor all other inputs, VIN= VCCor GND 5.5

42、 V 1 +0.1 A 2, 3 +1.0 Input current low 3009 IILFor input under test, VIN= GND For all other inputs, VIN= VCCor GND 5.5 V 1 -0.1 A 2, 3 -1.0 Quiescent supply current 3005 ICCFor all inputs, VIN= VCCor GND IOUT= 0 A 5.5 V 1 2.0 A 2, 3 20.0 Input capacitance 3012 CINTC= +25C, VIN= VCCor GND See 4.4.1c

43、 5.0 V 4 10 pF Power dissipation capacitance CPD4/ No load, f = 1 Mhz See 4.4.1c 5.0 V 4 8 pF See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96803 DLA LAND AND MARITIME COLUMBU

44、S, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +2.0 V VCC +5.5 V unless otherwise specified VCCGroup A subgroups Limits 3/ Unit Min Max Low leve

45、l ground bounce noise VOLP5/ VIH= VCC, VIL= 0.0 V TA= +25C See 4.4.1d See figure 4 5.0 V 4 1.6 V Low level ground bounce noise VOLV5/ 5.0 V 4 -1.5 High level VCCbounce noise VOHP5/ 5.0 V 4 0.5 High level VCCbounce noise VOHV5/ 5.0 V 4 -0.8 Functional test 3014 6/ VIN= VIHor VILVerify output VOSee 4.

46、4.1b 2.0 V 7, 8 L H 3.0 V 5.5 V Propagation delay time, mA to mY 3003 tPLH7/ CL= 15 pF minimum See figure 5 8/ 3.0 V and 3.6 V 9 8.9 ns 10, 11 1.0 10.5 4.5 V and 5.5 V 9 5.5 10, 11 1.0 6.5 CL= 50 pF minimum See figure 5 3.0 V and 3.6 V 9 11.4 10, 11 1.0 13.0 4.5 V and 5.5 V 9 7.0 10, 11 1.0 8.0 tPHL

47、7/ CL= 15 pF minimum See figure 5 8/ 3.0 V and 3.6 V 9 8.9 ns 10, 11 1.0 10.5 4.5 V and 5.5 V 9 5.5 10, 11 1.0 6.5 CL= 50 pF minimum See figure 5 3.0 V and 3.6 V 9 11.4 10, 11 1.0 13.0 4.5 V and 5.5 V 9 7.0 10, 11 1.0 8.0 See footnotes on next sheet. Provided by IHSNot for ResaleNo reproduction or n

48、etworking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96803 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. 1/ For tests not listed in the referenced MIL-STD-883, utilize the general test procedure of 883 under the conditions listed herein. 2/ Each input/output, as applicable, shall be tested at the specified temperature, for the specified limits, to the tests in table I herein. Output terminal