DLA SMD-5962-96823 REV B-2009 MICROCIRCUIT DIGITAL ADVANCED HIGH-SPEED CMOS QUADRUPLE 2-INPUT POSITIVE-NAND GATE TTL COMPATIBLE INPUTS MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change in accordance with the notice of revision 5962-R349-97. - jak 97-06-27 Monica L. Poelking B Incorporate previous Notice Of Revision (NOR). Update the boilerplate paragraphs to current requirements as specified in MIL-PRF-38535. - jak 09-01

2、-21 Charles F. Saffle REV SHET REV B B SHET 15 16 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby STANDARD MICROCIRCUIT DRAWING CHECKED BY Thanh V. Nguyen DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/w

3、ww.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 96-03-13 MICROCIRCUIT, DIGITAL, ADVANCED HIGH-SPEED CMOS, QUADRUPLE 2-INPUT POSITIVE-NAND GATE, TTL COMPATIBLE INPUTS, MONOLITHIC SILICO

4、N AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-96823 SHEET 1 OF 16 DSCC FORM 2233 APR 97 5962-E128-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96823 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OH

5、IO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are

6、 reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 96823 01 Q C A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1

7、.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked device

8、s meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54AHCT00 Quadruple 2-

9、input positive-NAND gate, TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant,

10、non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-

11、T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduct

12、ion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96823 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) . -0.5 V dc to +7.0 V dc

13、DC input voltage range (VIN) . -0.5 V dc to +7.0 V dc 4/ DC output voltage range (VOUT) -0.5 V dc to VCC+0.5 V dc 4/ DC input clamp current (IIK) (VINVCC) 20 mA Continuous output current (IO) (VOUT= 0 V to VCC) . 25 mA Continuous current through VCCor GND 50 mA Maximum power dissipation at TA= +55C

14、(instill air) (PD) . 500 mW Storage temperature range (TSTG) -65C to +150C Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) . +175C 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) . +4.5 V dc

15、to +5.5 V dc Minimum high level input voltage (VIH) +2.0 V Maximum low level input voltage (VIL). +0.8 V Input voltage range (VIN) . +0.0 V dc to +5.5 V dc Output voltage range (VOUT) +0.0 V dc to VCCMaximum high level output current (IOH) . -8 mA Maximum low level output current (IOL) . +8 mA Minim

16、um input rise or fall rate (t/V). +20 ns/V Case operating temperature range (TC) -55C to +125C 1/ Stresses above the absolute maximum rating may cause permanent damage to the device, Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, a

17、ll voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ The input and output voltage ratings may be exceeded providing that the input and output current ratings are observed. Pro

18、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96823 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification,

19、 standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 -

20、Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings

21、. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a confli

22、ct between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requ

23、irements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirem

24、ents for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device c

25、lasses Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified

26、 on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce waveforms and test circuit. The ground bounce waveforms and test circuit shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit

27、 shall be as specified on figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96823 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical

28、 performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requir

29、ements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where mar

30、king of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38

31、535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL

32、-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be re

33、quired from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device clas

34、ses Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appe

35、ndix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this

36、drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewe

37、r. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 36 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT D

38、RAWING SIZE A 5962-96823 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC+125C +4.5 V VCC +5.5 V unless otherwise specified VC

39、CGroup A subgroups Limits 3/ Unit Min Max IOH= -50 A 1, 2, 3 4.4 1 3.94 High level output voltage 3006 VOHFor all inputs affecting outputs under test, VIH= 2.0 V or VIL= 0.8 V For all other inputs, VIN= VCCor GND IOH= -8 mA 4.5 V 2, 3 3.8 V IOL= +50 A 1, 2, 3 0.1 1 0.36 Low level output voltage 3007

40、 VOLFor all inputs affecting outputs under test, VIH= 2.0 V or VIL= 0.8 V For all other inputs, VIN= VCCor GND IOL= +8 mA 4.5 V 2, 3 0.44 V 1 +0.1 Input current high 3010 IIHFor input under test, VIN= VCCFor all other inputs, VIN= VCCor GND 5.5 V 2, 3 +1.0 A 1 -0.1 Input current low 3009 IILFor inpu

41、t under test, VIN= GND For all other inputs, VIN= VCCor GND 5.5 V 2, 3 -1.0 A 1 2.0 Quiescent supply current, 3005 ICCFor all inputs, VIN= VCCor GND IOUT= 0.0 A 5.5 V 2, 3 20.0 A 1 1.35 Quiescent supply current delta, TTL input levels ICC4/ One input at 3.4 V Other inputs VCCor GND 5.5 V 2, 3 1.5 mA

42、 Input capacitance 3012 CINTC= +25C VIN= VCCor GND See 4.4.1c 5.0 V 4 8.0 pF Power dissipation capacitance CPD5/ CL= 50 pF minimum f = 1 MHz See 4.4.1c 5.0 V 4 11.5 pF VOLP6/ 5.0 V 4 1750 Low level ground bounce noise VOLV6/ 5.0 V 4 -1750 mV VOHP6/ 5.0 V 4 750 High level VCCbounce noise VOHV6/ VIH=

43、3.0 V,VIL = 0.0 V TA= +25C See 4.4.1d See figure 4 5.0 V 4 -750 mV See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96823 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990

44、 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC+125C +4.5 V VCC +5.5 V unless otherwise specified VCCGroup A subgroups Limits 3/ Unit Min Max Functional tests 3014 7/ VIH=

45、 2.0 V or VIL= 0.8 V Verify output VOSee 4.4.1b 4.5 V and 5.5 V 7, 8 L H 9 6.9 CL= 15 pF minimum See figure 5 8/ 4.5 V and 5.5 V 10, 11 1.0 8.0 ns 9 7.9 tPLH9/ CL= 50 pF minimum See figure 5 4.5 V and 5.5 V 10, 11 1.0 9.0 ns 9 6.9 CL= 15 pF minimum See figure 5 8/ 4.5 V and 5.5 V 10, 11 1.0 8.0 ns 9

46、 7.9 Propagation delay time, mA or mB to mY 3003 tPHL9/ CL= 50 pF minimum See figure 5 4.5 V and 5.5 V 10, 11 1.0 9.0 ns 1/ For tests not listed in the referenced MIL-STD-883 (e.g. ICC) utilize the general test procedure under the conditions listed herein. 2/ Each input/output, as applicable, shall

47、be tested at the specified temperature, for the specified limits to the tests in table I herein. Output terminals not designated shall be high level logic, low level logic, or open, except for all ICCtests, the output terminals shall be open. When performing the ICCtests, the current meter shall be

48、placed in the circuit such that all current flows through the meter 3/ For negative and positive voltage and current values, the sign designates the potential difference in reference to GND and the direction of current flow, respectively; and the absolute value of the magnitude, not the sign, is relative to the minimum and maximum limits, as applicable, listed herein. 4/ This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than 0 V or VCC. This test may be performed either one in