DLA SMD-5962-98008 REV A-1999 MICROCIRCUIT DIGITAL RADIATION HARDENED ADVANCED CMOS QUAD 2-INPUT MULTIPLEXER WITH THREE-STATE NON-INVERTING OUTPUTS MONOLITHIC SILICON《微型电路 数字型 辐射加固.pdf

1、NOTICE OF REVISION (NOR)THIS REVISION DESCRIBED BELOW HAS BEEN AUTHORIZED FOR THE DOCUMENT LISTED.1. DATE(YYMMDD)99-0 5-05Form ApprovedOMB No. 0704-0188Public reporting burden for this collection is estimated to average 2 hours per response, including the time for reviewinginstructions, searching ex

2、isting data sources, gathering and maintaining the data needed, and completing and reviewing thecollection of information. Send comments regarding this burden estimate or any other aspect of this collection of information,including suggestions for reducing this burden, to Department of Defense, Wash

3、ington Headquarters Services, Directorate forInformation Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503.PLEASE DO NOT RETURN YOUR COMPLETED FORM TO E

4、ITHER OF THESE ADDRESSED. RETURN COMPLETEDFORM TO THE GOVERNMENT ISSUING CONTRACTING OFFICER FOR THE CONTRACT/ PROCURING ACTIVITYNUMBER LISTED IN ITEM 2 OF THIS FORM.2. PROCURINGACTIVITY NO.3. DODAAC4. ORIGINATORb. ADDRESS (Street, City, State, Zip Code)Defense Supply Center, Columbus3990 East Broad

5、 StreetColumbus, OH 43216-50005. CAGE CODE672686. NOR NO.5962-R054-99a. TYPED NAME (First, Middle Initial,Last)7. CAGE CODE672688. DOCUMENT NO.5962-980089. TITLE OF DOCUMENTMICROCIRCUIT, DIGITAL, RADIATION HARDENED, ADVANCED CMOS, QUAD 2-INPUT MULTIPLEXER WITH THREE-STATE NON-INVERTING OUTPUTS, MONO

6、LITHIC SILICON10. REVISION LETTER11. ECP NO.No users listed.a. CURRENTInitialb. NEWA12. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIESAll13. DESCRIPTION OF REVISIONSheet 1 : Revisions ltr column; add “A“.Revisions description column; add “ Changes in accordance with NOR 5962-R054-99“.Revisions

7、date column ; add “99-05-05“.Revision level block ; add “A”.Rev status of sheets; for sheet 1, 3 and 4, 17 through 23, add “A“.Sheet 3: 1.3 Absolute maximum ratings , Supply voltage range ( V cc ); change limits from “-0.5 V dc to +6.0 V dc , to “-0.5 V dc to +7.0 V dc”. Revision level block; add “A

8、”.Sheet 4 : Add new paragraph which states; “3.1.1 Microcircuit die . For the requirements for microcircuit die, see appendix A toThis document.“Revision level block; add “A“.Sheets 17 through 23: Add attached appendix A.CONTINUED ON NEXT SHEETS14. THIS SECTION FOR GOVERNMENT USE ONLYa. (X one) X (1

9、) Existing document supplemented by the NOR may be used in manufacture.(2) Revised document must be received before manufacturer may incorpor ate this change.(3) Custodian of master document shall make above revision and furnish revised document.b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FORGOVERNMENT

10、DSCC -VACc. TYPED NAME (First, Middle Initial, Last)MONICA L. POELKINGd. TITLECHIEF, CUSTOM MICROELECTRONICS TEAMe. SIGNATUREMONICA L. POELKINGf. DATE SIGNED(YYMMDD)99-0 5-0515a. ACTIVITY ACCOMPLISHING REVISIONDSCC -VACb. REVISION COMPLETED (Signature)LARRY T. GAUDERc. DATE SIGNED(YYMMDD)99-0 5-05DD

11、 Form 1695, APR 92 Previous editions are obsolete.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA 5962-98008DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 17DSCC FORM 2234APR 97Documen

12、t No : 5962-98008Revision : AAPPENDIX A NOR No : 5962-R054-99APPENDIX A FORMS A PART OF SMD 5962-9800 8 Sheet: 2 of 8 10. SCOPE10.1 Scope . This appendix establishes minimum requirements for microcircuit die to be supplied under the QualifiedManufacturers List (QML) Program. QML microcircuit die mee

13、ting the requirements of MIL-PRF-38535 and the manufacturersapproved QM plan for use in monolithic microcircuits, multichip modules (MCMs), hybrids, electronic modules, or devices usingchip and wire designs in accordance with MIL-PRF-38534 are specified herein. Two product assurance classes consisti

14、ng ofmilitary high reliability (device class Q) and space application (device Class V) are reflected in the Part or Identification Number(PIN). When available a choice of Radiation Hardiness Assurance (RHA) levels are reflected in the PIN.10.2 PIN . The PIN shall be as shown in the following example

15、:5962 F 98008 01 V 9 AFederal RHA Device Device Die DieStock class designator type class code Detailsdesignator (see 10.2.1) (see 10.2.2) designator (see 10.2.4)( see 10.2.3) Drawing Num ber 10.2.1 RHA designator . Device classes Q and V RHA identified die shall meet the MIL-PRF-38535 specified RHA

16、levels. Adash (-) indicates a non-RHA die.10.2.2 Device type(s) . The device type(s) shall identify the circuit function as follows:Device type Generic number Circuit function01 ACS257 Radiation hardened, SOS,advanced CMOS, quad 2-inputmultiplexer with three-state non-inverting outputs.10.2.3 Device

17、 class designator .Device class Device requirements documentationQ or V Certification and qualification to the die requirements of MIL-PRF-38535.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA 5962-98008DEFENSE SUPPL

18、Y CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 18DSCC FORM 2234APR 97Document No : 5962-98008Revision: AAPPENDIX A NOR No : 5962-R054-99APPENDIX A FORMS A PART OF SMD 5962-98008 Sheet: 3 of 8 10.2.4 Die Details . The die details designation shall be a unique letter which designate

19、s the dies physical dimensions, bondingpad location(s) and related electrical function(s), interface materials, and other assembly related information, for each product andvariant supplied to this appendix.10.2.4.1 Die Physical dimensions .Die Types Figure number01 A-110.2.4.2 Die Bonding pad locati

20、ons and Electrical functions .Die Types Figure number01 A-110.2.4.3 Interface Materials .Die Types Figure number01 A-110.2.4.4 Assembly related information .Die Types Figure number01 A-110.3 Absolute maximum ratings . See paragraph 1.3 within the body of this drawing for details.10.4 Recommended ope

21、rating conditions . See paragraph 1.4 within the body of this drawing for details.20. APPLICABLE DOCUMENTS20.1 Government specifications, standards, bulletin, and handbooks . Unless otherwise specified, the following specifications,standards, bulletin, and handbook of the issue listed in that issue

22、of the Department of Defense Index of Specifications andStandards specified in the solicitation, form a part of this drawing to the extent specified herein.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA 5962-98008DE

23、FENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 19DSCC FORM 2234APR 97Document No : 5962-98008Revision: AAPPENDIX A NOR No : 5962-R054-99APPENDIX A FORMS A PART OF SMD 5962-98008 Sheet: 4 of 8 SPECIFICATIONDEPARTMENT OF DEFENSEMIL-PRF-38535 - Integrated Circuits, Manufac

24、turing, General Specification for.STANDARDSDEPARTMENT OF DEFENSEMIL-STD-883 - Test Method Standard Microcircuits.HANDBOOKDEPARTMENT OF DEFENSEMIL-HDBK-103 - List of Standard Microcircuit Drawings.(Copies of the specification, standards, bulletin, and handbook required by manufacturers in connection

25、with specific acquisitionfunctions should be obtained from the contracting activity or as directed by the contracting activity).20.2 Order of precedence . In the event of a conflict between the text of this drawing and the references cited herein, the text ofthis drawing shall take precedence.30. RE

26、QUIREMENTS30.1 Item Requirements . The individual item requirements for device classes Q and V shall be in accordance withMIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. Themodification in the QM plan shall not effect the form, fit or fu

27、nction as described herein.30.2 Design, construction and physical dimensions . The design, construction and physical dimensions shall be as specified inMIL-PRF-38535 and the manufacturers QM plan, for device classes Q and V and herein.30.2.1 Die Physical dimensions . The die physical dimensions shal

28、l be as specified in 10.2.4.1 and on figure A-1.30.2.2 Die bonding pad locations and electrical functions . The die bonding pad locations and electrical functions shall be asspecified in 10.2.4.2 and on figure A-1.30.2.3 Interface materials . The interface materials for the die shall be as specified

29、 in 10.2.4.3 and on figure A-1.30.2.4 Assembly related information . The assembly related information shall be as specified in 10.2.4.4 and figure A-1.30.2.5 Truth table . The truth table shall be as defined within paragraph 3.2.3 of the body of this document.30.2.6 Radiation exposure circuit . The

30、radiation exposure circuit shall be as defined within paragraph 3.2.6 of the body of thisdocument.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA 5962-98008DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVI

31、SION LEVEL A SHEET 20DSCC FORM 2234APR 97Document No : 5962-98008Revision: AAPPENDIX A NOR No : 5962-R054-99APPENDIX A FORMS A PART OF SMD 5962-98008 Sheet: 5 of 8 30.3 Electrical performance characteristics and post- irradiation parameter limits . Unless otherwise specified herein, theelectrical pe

32、rformance characteristics and post-irradiation parameter limits are as specified in table I of the body of this document.30.4 Electrical test requirements . The wafer probe test requirements shall include functional and parametric testing sufficient tomake the packaged die capable of meeting the ele

33、ctrical performance requirements in table I.30.5 Marking . As a minimum, each unique lot of die, loaded in single or multiple stack of carriers, for shipment to a customer,shall be identified with the wafer lot number, the certification mark, the manufacturers identification and the PIN listed in 10

34、.2herein. The certification mark shall be a “QML” or “Q” as required by MIL-PRF-38535.30.6 Certification of compliance . For device classes Q and V, a certificate of compliance shall be required from aQML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 60.4 here

35、in). The certificate ofcompliance submitted to DSCC-VA prior to listing as an approved source of supply for this appendix shall affirm that themanufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and the requirements herein.30.7 Certificate of conformance . A ce

36、rtificate of conformance as required for device classes Q and V in MIL-PRF-38535 shallbe provided with each lot of microcircuit die delivered to this drawing.40. QUALITY ASSURANCE PROVISIONS40.1 Sampling and inspection . For device classes Q and V, die sampling and inspection procedures shall be in

37、accordancewith MIL-PRF-38535 or as modified in the device manufacturers Quality Management (QM) plan. The modifications in the QMplan shall not effect the form, fit or function as described herein.40.2 Screening . For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and a

38、s defined in themanufacturers QM plan. As a minimum it shall consist of:a) Wafer Lot acceptance for Class V product using the criteria defined within MIL-STD-883 TM 5007.b) 100% wafer probe (see parag raph 30.4).c) 100% internal visual inspection to the applicable class Q or V criteria defined withi

39、n MIL-STD-883 TM2010or the alternate procedures allowed within MIL-STD-883 TM5004.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA 5962-98008DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHE

40、ET 21DSCC FORM 2234APR 97Document No : 5962-98008Revisi on: AAPPENDIX A NOR No : 5962-R054-99APPENDIX A FORMS A PART OF SMD 5962-98008 Sheet: 6 of 8 40.3 Conformance inspection .40.3.1 Group E inspection . Group E inspection is required only for parts intended to be identified as radiation assured (

41、see30.5 herein). RHA levels for device classes Q and V shall be as specified in MIL-PRF-38535. End point electrical testing ofpackaged die shall be as specified in table IIA herein. Group E tests and conditions are as specified within paragraphs 4.4.4.1,4.4.4.1.1, 4.4.4.2, 4.4.4.3, and 4.4.4.4.50. D

42、IE CARRIER50.1 Die carrier requirements . The requirements for the die carrier shall be in accordance with the manufacturers QM plan oras specified in the purchase order by the acquiring activity. The die carrier shall provide adequate physical, mechanical andelectrostatic protection.60. NOTES60.1 I

43、ntended use . Microcircuit die conforming to this drawing are intended for use in microcircuits built in accordance withMIL-PRF-38535 or MIL-PRF-38534 for government microcircuit applications (original equipment), design applications and logisticspurposes.60.2 Comments . Comments on this appendix sh

44、ould be directed to DSCC-VA, Columbus, Ohio, 43216-5000 or telephone(614)-692-0674.60.3 Abbreviations, symbols and definitions . The abbreviations, symbols, and definitions used herein are defined withMIL-PRF-38535 and MIL-HDBK-1331.60.4 Sources of Supply for device classes Q and V . Sources of supp

45、ly for device classes Q and V are listed in QML-38535.The vendors listed within QML-38535 have submitted a certificate of compliance (see 30.6 herein) to DSCC-VA and have agreedto this drawing.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDM

46、ICROCIRCUIT DRAWINGSIZEA 5962-98008DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 22DSCC FORM 2234APR 97Document No : 5962-98008Revision: AAPPENDIX A NOR No : 5962-R054-99APPENDIX A FORMS A PART OF SMD 5962-98008 Sheet: 7 of 8 FIGURE A-1o DIE PHYSICAL DIMENSIONSDie Si

47、ze: 2390 x 2390 microns.Die Thickness: 21 +/- 2 mils. DIE BONDING PAD LOCATIONS AND ELECTRICAL FUNCTIONSThe following metallization diagram supplies the locations and electrical functions of the bonding pads. The internal metallizationlayout and alphanumeric information contained within this diagram

48、 may or may not represent the actual circuit defined by this SMD.NOTE: Pad numbers reflect terminal numbers when placed in Case Outlines E, X (see Figure 1).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA 5962-98008D

49、EFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 23DSCC FORM 2234APR 97Document No : 5962-98008Revision: AAPPENDIX A NOR No : 5962-R054-99APPENDIX A FORMS A PART OF SMD 5962-98008 Sheet: 8 of 8 o INTERFACE MATERIALSDevice 01Metal 1: AlSi 7.0kA +/- 1.0kAMetal 2 (Top): AlSi 10.0kA