DLA SMD-5962-98642 REV C-2012 MICROCIRCUIT LINEAR VOLTAGE REGULATOR 5 VOLT NEGATIVE FIXED MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to reflect current requirements. 05-01-20 Raymond Monnin B Figure 2, case outlines N and T, correct terminal number 2. Add note to table II, Group C end-point electrical parameters. -gz. 09-09-02 Charles F. Saffle C Updated drawing

2、 paragraphs. -sld 12-05-15 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Mic

3、hael C. Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Raymond Monnin MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, 5 VOLT, NEGATIVE, FIXED, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 99-07-30 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268

4、 5962-98642 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E169-12Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98642 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97

5、 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assura

6、nce levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 98642 01 H T A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing n

7、umber 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as fo

8、llows: Device type Generic number 1/ Circuit function 01 SDP7905A Negative voltage regulator, 5 volt, 1.0 A, fixed 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534

9、 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standa

10、rd military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperatur

11、e range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. The

12、se exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers intern

13、al, QML certified flow. This product may have a limited temperature range. 1/ The SDP7905A is similar to the 7905A listed on Standard Microcircuit Drawing 5962-88746. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE

14、A 5962-98642 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style N See figure 1 3 Z-tab with nonisolat

15、ed tab, (TO-257Z), with glass seal T See figure 1 3 Flange mount with nonisolated tab, (TO-257), with glass seal U See figure 1 3 Flange mount with isolated tab, (TO-257), with glass seal Z See figure 1 3 Z-tab with isolated tab, (TO-257Z), with glass seal 1.2.5 Lead finish. The lead finish shall be

16、 as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage: Operating or output shorted to ground . -35 V dc Transient -43 V dc 2/ Storage temperature range -65 C to +150 C Lead temperature (soldering, 10 seconds) +300 C Junction temperature (TJ) +150 C 3/ Power dissipation (PD):

17、 TC= +25 C . 15 W TA= +25 C . 3.0 W Thermal resistance, junction-to-case (qJC): Cases N and T . 3.5 C/W Cases U and Z . 4.2 C/W Thermal resistance, junction-to-ambient (qJA) . 42 C/W 1.4 Recommended operating conditions. Input voltage range -7.5 V dc to -20 V dc Ambient operating temperature range (

18、TA) -55 C to +125 C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solic

19、itation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability.

20、2/ The -43 volt input rating refers to the ability of the regulator to withstand high line or transient condition without damage. Since the regulators maximum current capability is reduced, the output may fall out of regulation at high input voltages under nominal loading. 3/ The device is protected

21、 by a thermal shutdown circuit which is designed to turn off the output transistor whenever the device junction temperature is in excess of +150C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98642 DLA LAN

22、D AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of S

23、tandard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of preced

24、ence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirem

25、ents. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designate

26、d for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the for

27、m, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein a

28、nd figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating

29、 temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall b

30、e marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format)

31、 from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the

32、manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA L

33、and and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. Provi

34、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98642 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Con

35、ditions 1/ -55 C TA +125 C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VOUTTA= +25 C 1 01 -4.95 -5.05 V VIN= -7.5 V to -20 V 2/ 1, 2, 3 -4.85 -5.15 Line regulation 3/ 4/ VRLINEVIN= -7.5 V to -20 V 1 01 12 mV 2, 3 25 VIN= -8.0 V to -12 V 1 01 5 mV 2, 3

36、12 Load regulation 3/ VRLOADVIN= -10.0 V, IO= 5.0 mA to 1.5 A 1 01 20 mV 2, 3 25 VIN= -10.0 V, IO= 250 mA to 750 mA 1 01 15 mV 2, 3 30 Standby current drain ISCD1 01 2.5 mA 2, 3 3.0 Standby current drain change with line D ISCD(line) VIN= -7.0 V to -20 V 1, 2, 3 01 0.4 mA Standby current drain chang

37、e with load D ISCD(load) IO= 5.0 mA to 1.0 A 1, 2, 3 01 0.4 mA Dropout voltage VDOVOUT= 100 mV, IO= 1.0 A 1, 2, 3 01 2.5 V Peak output current IO(pk)TA= +25 C 1 01 1.5 3.3 A Short circuit current 5/ IOSVIN= -35 V 1 01 1.2 A 2, 3 2.8 Ripple rejection OUTINVVDDf = 120 Hz, VIN= -8 V to -18 V 4 01 63 dB

38、 5, 6 6/ 60 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98642 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electri

39、cal performance characteristics Continued. Test Symbol Conditions 1/ -55 C TA +125 C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output noise voltage 6/ NOf = 10 Hz to 100 kHz, TA= +25 C 7 01 40 V/V rms Long term stability 6/ tVOUTDDt = 1000 hours, TA= +25 C 7 01 75

40、mV 1/ Unless otherwise specified, VIN= -10 V and IO= 500 mA. 2/ IO= 5 mA to 1.0 A, P 15 W. 3/ All measurements except output noise voltage and ripple rejection are made at constant junction temperature and with low duty cycle. 4/ Minimum load current for full line regulation is 5.0 mA. 5/ Short circ

41、uit protection is only assured up to VIN= -35 V. 6/ If not tested, shall be guaranteed to the limits specified in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98642 DLA LAND AND MARITIME COLUMBUS,

42、 OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outlines T and U. Inches mm 0.005 0.13 0.010 0.25 0.020 0.51 Symbol Millimeters Inches Min Max Min Max A 4.83 5.08 .190 .200 A1 0.89 1.14 .035 .045 A2 3.05 BSC .120 BSC b 0.64 0.89 .025 .035 D 16.38 16.89 .645 .665 D1 10.41 10.92 .

43、410 .430 D3 0.00 1.65 .000 .065 e 2.54 BSC .100 BSC E 10.41 10.72 .410 .422 L 12.70 19.05 .500 .750 O 13.39 13.64 .527 .537 P 3.56 3.81 .140 .150 NOTE: The U.S. government preferred system of measurement is the metric SI system. However, this item was originally designed using inch-pound units of me

44、asurement. In the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98642 DLA LAND

45、 AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Case outlines N and Z. Symbol Millimeters Inches Min Max Min Max A 23.11 23.37 .910 .920 A1 10.41 10.67 .410 .420 A2 6.22 6.48 .245 .255 A3 3.05 3.30 .120 .130 b 0.71 0.81 .028 .032 D 4.70 5.59 .135 .220 D1 2.92 3

46、.18 .115 .125 D2 0.89 1.14 .035 .045 e 2.54 BSC .100 BSC L 10.41 10.67 .410 .420 L1 12.70 19.05 .500 .750 L2 6.22 6.48 .245 .255 L3 3.05 3.30 .120 .130 P 3.05 3.30 .120 .130 NOTE: The U.S. government preferred system of measurement is the metric SI system. However, this item was originally designed

47、using inch-pound units of measurement. In the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCI

48、RCUIT DRAWING SIZE A 5962-98642 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 Device type 01 Case outlines N and T (nonisolated tab) U and Z (isolated tab) Terminal number Terminal symbol Terminal symbol 1 2 3 Tab Ground Input Output Input Ground Input Output No connection FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted