DLA SMD-5962-99518 REV D-2013 MICROCIRCUIT HYBRID LINEAR 12 VOLT DUAL CHANNEL DC DC CONVERTER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to reflect current requirements. 05-02-14 Raymond Monnin B Figure 2, Terminal connections; Changed the terminal symbol, pin 9 from “Return Sense“ to “Negative Output“ and terminal symbol, pin 10 from “Positive Sense“ to “Output Vol

2、tage Trim“. -sld 05-06-15 Raymond Monnin C Added footnote 1 to table II, under group C end-point electricals. Updated drawing paragraphs. -sld 11-03-07 Charles F. Saffle D Corrected dimensions for symbols D, D2, and L1 for case outline U. Corrected dimensions for symbols D2, L, and L1 for case outli

3、ne X. Corrected dimensions for symbols D, L, and L1 for case outline Y. Corrected dimensions for symbols D, D2, and L1 for case outline Z. -sld 13-08-19 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY S

4、teve L. Duncan DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HY

5、BRID, LINEAR, 12 VOLT, DUAL CHANNEL, DC/DC CONVERTER DRAWING APPROVAL DATE 98-12-17 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-99518 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E234-13Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD M

6、ICROCIRCUIT DRAWING SIZE A 5962-99518 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes

7、which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 99518 01 H X X Federal RHA Device Device Case Lead stock class

8、designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate

9、 RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 AFL27012D/CH DC/DC converter, 96 W, 12 V output 1.2.3 Device class designator. This device class designator shall

10、be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performa

11、nce documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard mili

12、tary quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices wh

13、ich are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely

14、affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline lette

15、r Descriptive designator Terminals Package style U See figure 1 12 Y case configuration with leads bent upwards X See figure 1 12 Straight leads with end mounting through holes Y See figure 1 12 Straight leads with side mounting through holes Z See figure 1 12 Y case configuration with leads bent do

16、wnwards 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99518 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET

17、3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Input voltage range -0.5 V dc to +500 V dc Lead temperature (soldering, 10 seconds) +300C Storage temperature range . -65C to +135C 1.4 Recommended operating conditions. Input voltage range +160 V dc to +400 V dc Output power 2/ 3/ . 96 W Case

18、 operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents

19、are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outl

20、ines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, P

21、hiladelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has

22、been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufactur

23、ers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modi

24、fication in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 1/ Stresses above the absolute ma

25、ximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Derate output power linearly above case temperature +125C to 0 at +135C. 3/ Output load must be distributed so that a minimum of 20% of the total output

26、power is being provided by one of the outputs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99518 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3.2.1 Case o

27、utline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

28、as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marki

29、ng of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the devic

30、e described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed

31、. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime- VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to t

32、his drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime- VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shal

33、l be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan s

34、hall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by th

35、e manufacturer under document revision level control and shall be made available to either DLA Land and Maritime- VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified

36、 in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manu

37、facturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99518 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics.

38、Test Symbol Conditions -55C TC +125C VIN= 270 V dc 5%, CL= 0 unless otherwise specified Group A Subgroups Device type Limits Unit Min Max Output voltage VOUTIOUT= 4 A 1 01 11.88 12.12 V 2,3 11.76 12.24 Output current 1/ IOUTVIN= 160, 270, and 400 V dc, either output 1,2,3 01 6.4 A Output ripple volt

39、age 2/ VRIPVIN= 160, 270, and 400 V dc, B.W. = 10 MHz, IOUT= 4 A, both outputs 1,2,3 01 80 mV p-p Line regulation 3/ VRLINEVIN= 160, 270, and 400 V dc, IOUT= 0, 2, and 4 A, both outputs 1,2,3 01 60 mV Load regulation 3/ VRLOADVIN= 160, 270, and 400 V dc, IOUT= 0, 2, and 4 A, both outputs 1,2,3 01 12

40、0 mV Cross regulation 4/ Positive output Negative output VRCROSVIN= 160, 270, and 400 V dc 1,2,3 01 120 mV 600 Input current IINIOUT= no load 1 01 10 mA 2,3 12 Enable 1, (pin 4) shorted to Input return (pin 2) 1,2,3 3 Enable 2, (pin 12) shorted to Output return (pin 8) 1,2,3 5 Input ripple current 2

41、/ IRIPIOUT= 4 A, B.W. = 10 MHz 1,2,3 01 60 mA p-p Efficiency EFFIOUT = 4 A, both outputs, TC= +25C 1 01 82 % Isolation ISO Input to output or any pin to case (except pin 3) at 500 V dc, TC= +25C 1 01 100 M Maximum capacitive load 5/ CLEach output, TC= +25C 4 01 10,000 F Power dissipation load fault

42、PD Overload 6/ 1,2,3 01 30 W Short circuit 30 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99518 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC

43、 FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC +125C VIN= 270 V dc 5%, CL= 0 unless otherwise specified Group A Subgroups Device type Limits Unit Min Max Current limit point 7/ ICLVOUT= 90% VNOM1 01 4.6 5.0 A 2 4.2 4.6 3 5.0 5.6 Switchin

44、g frequency FS4,5,6 01 500 600 kHz Sync frequency range FSYNC4,5,6 01 500 700 kHz Output response to step transient load changes 8/ VOTLOAD50% to/from 100% 4,5,6 01 -750 +750 mV pk 10% to/from 50% -750 +750 Recovery time, step transient load changes 8/ 9/ TTLOAD50% to/from 100% 4,5,6 01 200 s 10% to

45、/from 50% 400 Output response to transient step line changes 5/ 10/ VOTLINEInput step 160 V to/from 400 V dc 4,5,6 01 -500 +500 mV pk Recovery time transient step line changes 5/ 8/ 10/ TTLINEInput step, 160 V to/from 400 V dc 4,5,6 01 500 s Turn on overshoot VTonosEnable 1 and 2 on. (Pins 4 and 12

46、high or open) 4,5,6 01 250 mV pk Turn on delay 11/ TonDEnable 1 and 2 on. (Pins 4 and 12 high or open) 4,5,6 01 120 ms Load fault recovery 5/ TrLF4,5,6 01 120 ms 1/ Parameter guaranteed by line and load regulation tests. 2/ Bandwidth guaranteed by design. Tested for 20 kHz to 10 MHz. 3/ Load current

47、 split equally between +VOUTand -VOUT. 4/ Cross regulation measured with load on tested output at 20% while changing the load on the other output from 20% to 80%. 5/ Parameter shall be tested as part of design characterization and after design or process changes. Thereafter, parameters shall be guar

48、anteed to the limits specified in table I. 6/ An overload is that condition with a load in excess of the rated load but less than that necessary to trigger the short circuit protection and is the condition of maximum power dissipation. 7/ Current limit point is that condition of excess load causing output voltage to drop 90% of nominal. 8/ Load step transition time 10 microseconds. 9/ Recovery time is measured from the initiation of the transient to where VOUThas returned to within 1% of VOUTat 50% lo