1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - gt 02-05-22 Raymond Monnin REV SHET REV A SHET 15 REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENT
2、ER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY RAJESH PITHADIA COLUMBUS, OHIO 43216 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY RAYMOND MONNIN MICROCIRCUIT, DIGITAL-LINEAR, DUAL, 12-BIT, PROGRAMMABLE, DIGITAL-TO-ANALOG AND AGENCIES OF THE DEPARTMENT
3、OF DEFENSE DRAWING APPROVAL DATE 99-10-20 CONVERTER, MONOLITHIC SILICON AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-99557 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E383-02 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reprod
4、uction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99557 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting
5、 of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1
6、.2 PIN. The PIN is as shown in the following example: 5962 - 99557 01 Q P X Federal stock class designator RHA designator (see 1.2.1) Devicetype (see 1.2.2) Device class designator Caseoutline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q a
7、nd V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
8、 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 TLV5618AM Dual, 12-bit, programmable digital-to-analog converter with power down 02 TLC5618AM Dual, 12-bit, programmable digital-to-analog converter 1.2.3 Device class d
9、esignator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535
10、, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 2 CQCC1-N20 20 Square leadless chip ca
11、rrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99557 DEFE
12、NSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VDDto AGND) .7 V Digital input voltage range to AGND-0.3 V VDD+0.3 V Reference input voltage range to AGND .-0.3 V VDD+0.3 V Output voltage at OUTPUT p
13、in from external source (device type 02 only) VDD+0.3 V Continuous current at any terminal (device type 02 only)20 mA Power dissipation (PD): (TA 25C) Case P .1050 mW 2/ Case 21375 mW 3/ Junction temperature (TJ)+150C Storage temperature range .-65C to +150C Lead temperature 1.6 mm (1/16 inch) from
14、case for 10 seconds260C Thermal resistance, junction-to-case (JC) .See MIL-STD-1835 1.4 Recommended operating conditions. Supply voltage (VDD): Device type 01: With VDD= 5 V.4.5 V to 5.5 V With VDD= 3 V.2.7 V to 3.3 V Device type 02 .4.5 V to 5.5 V High level digital input voltage (VIH): Device type
15、 01 (with VDD= 2.7 V to 5.5 V)2 V minimum Device type 02 (with VDD= 5 V) 0.7 VDDminimum 4/ Low level digital input voltage (VIL): Device type 01 (with VDD2.7 V to 5.5 V).0.8 V maximum Device type 02 (with VDD= 5 V) 0.3 VDDmaximum 4/ Load resistance (RL) .2 k Load capacitance (CL) (device type 01 onl
16、y).100 pF maximum Clock frequency (fCLK) (device type 01 only) 20 MHz Ambient operating temperature range (TA) .-55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the exten
17、t specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrated Ci
18、rcuits, Manufacturing, General Specification for. 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ For case P, the derating factor above TA= +25C is 8.4 mW/C. 3/ For cas
19、e 2, the derating factor above TA= +25C is 11.0 mW/C. 4/ This parameter is not production tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99557 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
20、 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780
21、- Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between
22、the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements fo
23、r device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for de
24、vice class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q an
25、d V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Block diagrams. The block diagrams shall be as specified
26、on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature ran
27、ge. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be
28、marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for devic
29、e classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML” or “Q” as required in MIL-PRF-38535. The compliance m
30、ark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99557 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A
31、SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Power supply section Power supply current IDDDAC latch = 0X800, fast 1,2,3 01 2.3 mA no load, slow 1 all
32、 inputs = AGND or VDDVDD= 5.5 V, fast 02 2.5 no load, slow 1 all inputs = 0 V or VDDReference input section Input voltage range VINREFIN = 2.048 V 1,2,3 01 0 VDD1.5 V 02 0 VDD -2 Digital inputs section High level digital input current IIHVIN= VDD1,2,3 01 1 A ( DIN, SCLK, CS pins ), VIN= VDD02 1 Low
33、level digital input current IILVIN= 0 V 1,2,3 01 -1 A ( DIN, SCLK, CS pins ), VIN= 0 V 02 -1 Output sections Output voltage range VOUTRL= 10 k 1,2,3 01 0 VDD-0.4 V ( OUTPUT A, OUTPUT B pins ), RL= 10 k 02 VDD-0.4 Output load regulation accuracy VOLRVO= 4.096 V, 2.048 V, RL= 2 k 1,2,3 01 0.29 % of FS
34、 voltage ( OUTPUT A, OUTPUT B pins ), VO(OUT)= 4.096 V, RL= 2 k 02 0.29 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99557 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216
35、-5000 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Static DAC section Resolution RES 1,2,3 All 12 bits Integral nonlineari
36、ty 2/ INL 1,2,3 01 4 LSB End point adjusted 02 4 Differential nonlinearity 3/ DNL 1,2,3 All 1 LSB Zero scale error, 4/ EZS 1,2,3 All 12 mV offset error at zero scale Gain error EG 5/ 1,2,3 All 0.6 % of FS voltage Analog output dynamic section Positive output slew rate +SR CL= 100 pF, Slow 4 02 0.3 V
37、/s RL= 10 k, code 32 to code 4096, TA= +25C, Fast 2.4 VOUTfrom 10 % to 90 % Negative output slew rate -SR CL= 100 pF, Slow 4 02 0.15 V/s RL= 10 k, code 4096 to code 32, TA= +25C, Fast 1.2 VOUTfrom 10 % to 90 % See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking
38、permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99557 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless oth
39、erwise specified Group A subgroups Device type Limits Unit Min Max Analog output dynamic section - continued Signal to noise ratio SNR fS= 102 kSPS, fOUT= 1 kHz, CL= 100 pF, RL= 10 k 4,5,6 01 72 dB Signal to noise + distortion SINAD fS= 102 kSPS, fOUT= 1 kHz, CL= 100 pF, RL= 10 k 4,5,6 01 58 dB Tota
40、l harmonic distortion THD fS= 102 kSPS, fOUT= 1 kHz, CL= 100 pF, RL= 10 k 4,5,6 01 -57 dB Spurious free dynamic range SFDR fS= 102 kSPS, fOUT= 1 kHz, CL= 100 pF, RL= 10 k 4,5,6 01 57 dB Digital input timing section Setup time, CS low before first negative SCLK edge tsu (CS-CK) See figure 3 9,10,11 A
41、ll 5 ns Setup time, 16thnegative SCLK edge before CS rising edge tsu (C16-CS) See figure 3 9,10,11 All 10 ns SCLK pulse width high tWHSee figure 3 9,10,11 All 25 ns SCLK pulse width low tWLSee figure 3 9,10,11 All 25 ns Setup time, data ready before SCLK falling edge tsu(D)See figure 3 9,10,11 All 8
42、 ns Hold time, data held valid after SCLK falling edge th(D)See figure 3 9,10,11 All 5 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99557 DEFENSE SUPPLY CENTER COLUMBUS CO
43、LUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. 1/ Unless otherwise specified, VDD= 2.7 V to 5.5 V for device type 01. VDD= 5 V 5 %, Vref(REFIN)= 2.048 V for device type 02. 2/ The relative accuracy or integral nonline
44、arity (INL) sometimes referred to as linearity error, is the maximum deviation of the output from the line between zero and full scale excluding the effects of zero code and full scale errors. 3/ The differential nonlinearity (DNL) sometimes referred to as differential error, is the difference betwe
45、en the measure and ideal 1 LSB amplitude change of any two adjacent codes. Monotonic means the output voltage changes in the same direction (or remains constant) as a change in the digital input code. 4/ Zero scale error is the deviation from zero voltage output when the digital input code is zero.
46、5/ Gain error is the deviation from the ideal output (2 Vref 1 LSB) with an output load of 10 k. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6
47、.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this d
48、rawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1