DLA SMD-5962-99566 REV B-2010 MICROCIRCUIT HYBRID LINEAR PLUS MINUS 9 5 VOLT DUAL CHANNEL DC DC CONVERTER.pdf

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Table I, Efficiency test, change minimum limit for subgroup 1 from 83% to 82% and subgroups 2, 3 from 83% to 80%. Update drawing boilerplate. 03-05-28 Raymond Monnin B Added footnote 1 to table II, under group C end-point electricals. Updated dra

2、wing paragraphs. -sld 10-12-03 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve L. Duncan DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones COLUMBUS, OHIO 43218-3

3、990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, 9.5 VOLT, DUAL CHANNEL, DC/DC CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 99-06-24 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 6

4、7268 5962-99566 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E455-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99566 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 A

5、PR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness a

6、ssurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 99566 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Draw

7、ing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function

8、as follows: Device type Generic number Circuit function 01 MOR289R5D DC/DC converter, 105 W, 9.5 V outputs 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and req

9、uire QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard milit

10、ary quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range,

11、 manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exce

12、ption(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML

13、 certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99566 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 223

14、4 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style T See figure 1 12 Tabbed flange mount, lead formed up U See figure 1 12 Flange mount, lead formed down X See figure 1 12 Flange mount, s

15、hort lead Y See figure 1 12 Tabbed flange mount, short lead Z See figure 1 12 Tabbed flange mount, lead formed down 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage range (VIN) 2/ . -0.5 V dc to +50 V dc Power dissipation (PD)

16、. 24 W Lead temperature (10 seconds) +300C Storage temperature range -65C to +150C 1.4 Recommended operating conditions. Input voltage range (VIN) . +16 V dc to +40 V dc Output power . 105 W Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, sta

17、ndards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybr

18、id Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780

19、 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses above the absolute maximum ratings may cause perma

20、nent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ An undervoltage lockout circuit shuts the unit off when the input voltage drops to approximately 14.5 volts. Operation of the unit between 14.5 volts and 16 volts is nondestructive,

21、 but performance is not guaranteed. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99566 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence

22、. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements

23、. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for

24、the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit

25、, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and

26、 figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating t

27、emperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall

28、 be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables forma

29、t) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by th

30、e manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA

31、 Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4.

32、VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by

33、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99566 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Condition

34、s -55C TC+125C VIN= 28 V dc 0.5 V dc no external sync, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output Voltage (+VOUT)(-VOUT)VOUTIOUT= +5.53 A dc, (main) 1 01 +9.410 +9.580 V dc 2,3 +9.400 +9.600 IOUT= -5.53 A dc, (dual) 1 -9.360 -9.630 2,3 -9.350 -9.650 Out

35、put current 1/ IOUTVIN= 16 V dc, 28 V dc, and 40 V dc, sum of both outputs 1,2,3 11 A VOUTripple voltage VRIPIOUT= 5.53 A, B.W. = 10 kHz to 20 MHz 1 100 mV p-p 2,3 120 VOUTline regulation VRLINEVIN= 40 V dc to 16 V dc, IOUT= 5.53 A dc, (main) 1,2,3 50 mV VIN= 40 V dc to 16 V dc, IOUT= 5.53 A dc, (du

36、al) 100 VOUTload (+VOUT)regulation (-VOUT)VRLOADIOUT= 0 to 5.53 A, (main) 1,2,3 50 mV IOUT= 0 to 5.53 A, (dual) 200 Input current IINIOUT= 0, inhibit (pin 4) = 0 1, 2, 3 10 mA IOUT= 0, inhibit (pin 12) = 0 60 IOUT= 0, inhibit pins (pins 4 and 12) = open 160 IIN ripple current IRIPIOUT= 5.53 A, B.W.

37、= 10 kHz to 20 MHz 1 120 mA p-p 2, 3 130 Efficiency Eff IOUT=5.53 A 1 82 % 2,3 80Isolation ISO Input to output or any pin to case at 500 V dc, TC=+25C 1 100 M Capacitive load 2/ 3/ CLNo effect on dc performance, TC=+25C 4 1000 F See footnotes at end of table. Provided by IHSNot for ResaleNo reproduc

38、tion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99566 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC+125C VI

39、N= 28 V dc 0.5 V dc no external sync, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Power dissipation, load fault PDShort circuit 1,2,3 01 24 W Switching frequency FSIOUT= 5.53 A 4 480 580 kHz 5, 6 460 600 External sync range 4/ FSYNCIOUT= 5.53 A, TTL level to pi

40、n 6 4,5,6 525 625 kHz Step VOUT load transient 5/ VTLOAD50 percent load to/from 100 percent load -500 +500 mV pk Recovery time, step VOUTtransient 3/ 5/ 6/ TTLOAD50 percent load to/from 100 percent load 300 s Step VOUTtransient lines 3/ 7/ VTLINEInput step from 40 V dc to 16 V dc, IOUT = 5.53 A -600

41、 +600 mV pk Input step from 16 V dc to 40 V dc, IOUT = 5.53 A -600 +600 Recovery step VOUTline transient 3/ 6/ TTLINEInput step from 16 V dc to 40 V dc, IOUT = 5.53 A 300 s Input step from 40 V dc to 16 V dc, IOUT = 5.53 A 300 Start up overshoot 3/ VtonosIOUT= 5.53 A, VIN= 0 to 28 V dc 50 mV pk Star

42、t up delay 8/ TonDIOUT= 5.53 A, VIN= 0 to 40 V dc 10 ms Load fault recovery 3/ TrLFIOUT= 5.53 A 10 ms 1/ The output power available from either output is limited to 73.5 watts (i.e. 70 percent of the total output power), while the other maintains a minimum of 15 percent of the total output power use

43、d. 2/ Capacitive load may be any value from 0 to the maximum limit without compromising dc performance. 3 Parameter shall be tested as part of design characterization and after design or process changes; therefore, the parameter shall be guaranteed to the limits specified in table I. 4/ A TTL level

44、waveform (VIH= 4.5 V minimum, VIL= 0.8 V maximum) with a 50 percent 10 percent duty cycle applied to the sync input pin (pin 6) within the sync range frequency shall cause the converters switching frequency to become synchronous with the frequency applied to the sync input pin (pin 6). 5/ Load step

45、transition time is 50 microseconds minimum. 6/ Recovery time is measured from the initiation of the transient until VOUThas returned to within 1 percent of its final value. 7/ Input step transition time greater than 10 microseconds. 8/ Start up delay time measurement is either for a step application

46、 of power at the input or the removal of a ground signal from the inhibit pin (pin 4) or inhibit 2 pin (pin 12) while power is applied to the input. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99566 DLA L

47、AND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Case outline T. Symbol Millimeters InchesMin Max Min MaxA 10.16 0.400A1 5.33 5.84 0.210 0.230b 0.89 1.14 0.035 0.045D 50.55 51.05 1.990 2.010D1 37.85 38.35 1.490 1.510e 5.08 BSC 0.200 BSCE 69.85 72.39 2.750 2.8

48、50E1 63.25 63.75 2.490 2.510F 1.14 1.40 0.045 0.055L 6.10 6.60 0.240 0.260P 3.43 3.68 0.135 0.145q/q1 44.32 44.58 1.745 1.755q2 29.08 29.34 1.145 1.155s 6.22 6.48 0.245 0.255T 9.91 12.45 0.390 0.490NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch- pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units s