DLA WW-P-460 E-2009 PIPE FITTINGS BRASS OR BRONZE (THREADED) CLASSES 125 AND 250 POUND.pdf

1、 FEDERAL SPECIFICATION PIPE FITTINGS; BRASS OR BRONZE (THREADED), CLASSES 125 AND 250 POUND The General Services Administration has authorized the use of this federal specification, by all Federal agencies. 1. SCOPE AND CLASSIFICATION 1.1 Scope. This specification covers threaded pipe fittings made

2、of brass or bronze, classes 125 and 250. Certain requirements also pertain to wrought or cast plugs, bushings, couplings, and caps. 1.2 Classification. Fittings are to be furnished in the size and pressure rating designated by the applicable detail specification sheet, as specified. 2. APPLICABLE DO

3、CUMENTS 2.1 Government publications. The following documents, of the issues in effect on the date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein: Detail Specification Sheet MS14305 - Fittings, Pipe, Brass or Bronze, Threaded (Tees, Cr

4、osses, 45-Deg. Elbows, and Couplings), Class 125 MS14306 - Fittings, Pipe, Brass or Bronze, Threaded (Reducers, Close and Open Return Bends, and 45-Deg. Y-Branches), Class 125 MS14307 - Elbows, Pipe, Brass or Bronze, Threaded, 45-Deg., Street, Class 125 MS14308 - Elbows, Pipe, Brass or Bronze, Threa

5、ded, 90-Deg., Reducing, Class 125 MS14309 - Tees, Pipe Brass or Bronze, Threaded, Reducing, Class 125 MS14310 - Caps, Pipe, Brass or Bronze, Threaded, Class 125 MS14311 - Fittings, Pipe, Brass or Bronze Threaded (90-Deg. Elbows, Tees, Crosses, 45-Deg. Elbows, and Couplings), Class 250 MS14312 - Elbo

6、ws, Pipe, Brass or Bronze, Threaded, 90-Deg., Reducing, Class 250 MS14314 - Plugs, Pipe, Brass or Bronze, Threaded (Square Head and Square Socket), Classes 250 and 125 MS51845 - Elbows, Pipe, Brass or Bronze, Threaded, 90-Deg., Straight, Class 125 (Copies of military specifications and standards req

7、uired by contractors in connection with specific procurement functions are obtained from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094 or available online at http:/assist.daps.dla.mil/quicksearch.) AMSC N/A FSC 4730 Beneficial comments, recomm

8、endations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: Defense Supply Center, Columbus, DSCC-VAI, 3990 East Broad Street, Columbus, OH 43218-5000, or emailed to, FluidFlowdscc.dla.mil. Since contact information can change, you may want to

9、 verify the currency of this address information using the ASSIST Online at http:/assist.daps.dla.mil. INCH-POUND WW-P-460E 15 December 2009 SUPERSEDING WW-P-460D 28 February 1994 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-WW-P-460E 2 2.2 Other

10、publications. The following documents form a part of this specification to the extent specified herein. Unless a specific issue is identified, the issue in effect on date of invitation for bids or request for proposal shall apply. American Society of Mechanical Engineers (ASME) ASME B16.15 - Cast Br

11、onze Threaded Fittings (Copies of these documents are available online at http:/www.asme.org or from the ASME International, Three Park Avenue, New York, NY 10016-5990.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein (except for

12、detail specification sheets), the text of this specification takes precedence. Nothing in this specification, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Specification sheets. The individual item requirements shall be as spec

13、ified herein and in accordance with the applicable specification sheets. 3.2 Requirements1.2. Fittings shall be furnished in the size and pressure rating designated by the applicable detail specification sheets, MS14305, MS14306, MS14307, MS14308, MS14309, MS14310, MS14311, MS14312, MS14314, and MS5

14、1845, (see and 6.2), and shall meet the applicable requirements of ASME B16.15. 3.3 First article4.2.1. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see and 6.2). 3.4 Pressure-temperature ratings. Pressure-temperature ratings shall be in

15、accordance with ASME Bl6.15. 3.5 Hydrostatic strength. Fittings shall be capable of withstanding, without rupture or any leakage, an internal hydrostatic pressure of two times the pressure rating for a period of one minute. 3.6 Size. Size and dimensions shall be in accordance with ASME B16.15. 3.7 M

16、aterial. The material shall be in accordance with ASME B16.15. 3.8 Tolerances. Tolerances shall be in accordance with ASME B16.15. 3.9 Threading. Threading shall be in accordance with ASME B16.15. 3.10 Marking. Marking shall be in accordance with ASME B16.15. 3.11 Workmanship. Workmanship shall be i

17、n accordance with ASME B16.15. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract, the contr

18、actor may use his own, or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the government. The government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed nec

19、essary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this document shall become a part of the contractors overall inspection system or quality program. Th

20、e absence of any inspection requirements in this document shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations

21、, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. Provided by IHSNot for ResaleNo reproduction or networking permit

22、ted without license from IHS-,-,-WW-P-460E 3 4.1.2 Component and material inspection. Components and materials shall be inspected in accordance with all the requirements specified herein and in applicable referenced documents. 4.2 Classification of inspections. The inspection requirements specified

23、herein are as follows: a. First article inspection (see 4.2.1). b. Quality conformance inspection (see 4.2.2). 4.2.1 First article inspection3.2. The first article inspection shall be performed on one fitting when a first article is required (see and 6.2). This inspection shall include the examinati

24、on of 4.3 and the test of 4.4. The first article may be either a first production item or a standard production item from the suppliers current inventory provided the item meets the requirements of the specification and is representative of the design, construction, and manufacturing technique appli

25、cable to the remaining items to be furnished under the contract. 4.2.2 Quality conformance inspection 4.3. The quality conformance inspection shall include the examination of , the test of 4.4, and the packaging inspection of 4.5. 4.3 Examination. Each fitting shall be examined for compliance with t

26、he requirements in section 3 of this document. This element of inspection shall encompass all visual examinations and dimensional measurements. Noncompliance with any specified requirements or presence of one or more defects preventing or lessening maximum efficiency shall constitute cause for rejec

27、tion. 4.4 Test. 4.4.1 Air pressure test. The first article shall be subjected to an air-pressure test of not less than 60 pounds per square inch gage (415 kilopascal) while the fitting is under water. The fitting shall not leak air at any part of the surface. 4.4.2 Alternate pressure test. As an alt

28、ernate test, the fitting shall be subjected to an internal hydrostatic pressure of two times the pressure rating for a period of one minute. Under the hydrostatic pressure test, the fitting shall not leak or sweat at any part of the surface. 4.5 Preparation for delivery inspection. The preservation,

29、 packaging, packing, and marking of the item shall be inspected to verify conformance to the requirements of section 5. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be perfo

30、rmed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within th

31、e Military Services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES INFORMATION FOR GUIDANCE ONLY. (This section contains informa

32、tion of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. The pipe fittings are intended for use as outlined below: 6.1.1 Class 125 fittings. Class 125 pipe fittings are generally used for saturated steam service with pressure/temperature ratings as requir

33、ed for class 125 fittings in ASME B16.15. 6.1.2 Class 250 fittings. Class 250 pipe fittings are normally used for saturated steam service with pressure/temperature ratings as required for Class 250 fittings in ASME B16.15. Provided by IHSNot for ResaleNo reproduction or networking permitted without

34、license from IHS-,-,-WW-P-460E 4 6.2 Acquisition requirements. Acquisition documents should specify the following: a. Title, number, and date of this specification. b. PIN required (see 1.2 and 3.1). c. When a first article is required for inspection and approval (see 3.2 and 4.2.1). d. Level of pre

35、servation and packaging, and level of packing required (see 5.1). 6.3 Data requirements. When this specification is used in an acquisition and data are required to be delivered, the data requirements will be developed as specified by an approved Data Item Description (DID) and delivered in accordanc

36、e with the approved Contract Data Requirements List (DD Form 1423) incorporated into the contract. When the provisions of DoD Federal Acquisition Regulations (FAR) Supplement, Part 27, Sub-Part 227.405-70 are invoked and the DD Form 1423 is not used, the data should be delivered by the contractor in

37、 accordance with the contract requirements. 6.4 Part Identification Number (PIN). The PIN to be used for fittings applied to this specification is found in the applicable MS sheet. 6.4.1 Guidance on use of alternative parts with less hazardous or nonhazardous materials. This specification provides f

38、or a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit and function requirements of their application. 6.5 Subject term (key word) listing. Bushings Caps Couplings Crosses Elbows Plugs Reducers Return Bends Tee

39、s Y-Branches 6.6 Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmental Protection Agency (EPA) is focusing efforts on reducing 3

40、1 priority chemicals. The list of chemicals is available on their website at http:/www.epa.gov/epawaste/hazard/wastemin/priority.htm. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of the materials on the list should be minimized or eliminated unless needed to

41、meet the requirements specified herein (see Section 3). 6.7 Guidance on use of alternative parts with less hazardous or non-hazardous materials. This specification provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that m

42、eets the form, fit, and function requirements of their application. 6.8 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking pe

43、rmitted without license from IHS-,-,-WW-P-460E 5 CONCLUDING MATERIAL MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS Navy - YD Military Coordinating Activity Custodians: Preparing activity: Army - CR4 DLA - CC Navy - YD Air Force - 99 DLA - CC (Project 4730-2009-002) Review activit

44、ies: Army - AR, CE, EA Navy - CG, MC Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-