DOD A-A-53543-1988 BOTTLE SCREWCAP《螺丝钉瓶》.pdf

1、A-A-53543 66 W 7777774 0033027 3 W k- A-A-5 354 3 30 June 1988 ib t COMMERCIAL ITEM DESCRIPTION BOTTLE, SCREWCAP The General Services Administration has authorized the use of this commercial item description. This commercial item description covers a 32 ounce capacity screwcap bottle suitable for st

2、oring laboratory chemicals, solutions and corrosive liquids. Salient characteristics. Shall be a 32 ounce capacity narrow-mouth screwcap bottle. Shall be of high-density polyethylene or polypropylene plastic. Shall be of natural color. Shall be cylindrical and symmetrical in shape and shall have a n

3、arrow-mouth with a continuous type thread finish. The mouth opening of the bottle shall be large enough to readily permit filling and dispensing of the contents. The normal capacity point of the bottle, shall not extend above the bottom level of the neck. Shall be so constructed that the bottle is s

4、table when placed on a smooth flat surface. The bottle shall be supplied with a one-piece molded polypropylene screw cap closure with a continuous type thread. With the screw cap hand tightened to the bottle, there shall be no evidence of leakage. To provide for firm gripping for removing and tighte

5、ning of the screw cap the outside vertical surface of the closure shall have ribs. Workmanship. The bottle shall be free from defects which detract from its appearance or impair its serviceability. Unit. Each (EA). One bottle, as specified, constitutes one unit . AMSC N/A FSC 6640 DISTRIBUTION STATE

6、MENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-53543 bb m 977977q 001LOZ 5 m A-A- 5 3 5 4 3 Quality Assurance Provisions. Responsibility for inspection

7、. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any facilities suitable for the per

8、formance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed require

9、ments. Records. Records of examinations and tests performed by or for the contractor shall be maintained by the contractor and made available to the Government upon the Governments request, at any time, or from time to time, during the performance of the contract and for a period of three years afte

10、r delivery of the supplies to which such records relate. 1 1 i Ins ection. Inspection, as used herein, is defined as both examination + such as visual or auditory investigation without the use of special laboratory appliances or procedures) and testing (determination by technical means of physical a

11、nd chemical properties) of the item. accordance with commercial practice. The unit of product for test purposes shall be one bottle. Sampling for tests. Sampling for tests shall be conducted in Tests. Tests shall be conducted to determine compliance with specification requirements. Where feasible, t

12、he same sample shall be used for one or more tests. Leak test. The bottle shall be filled with water at ambient temperature and the closure shall be hand tightened. The bottle shall be inverted for one hour and examined for evidence of leakage. Contractor certification. The contractor shall certify

13、that the product offered meets the salient characteristics of this description and conforms to the producers own drawings, specifications, standards, and quality assurance practices. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-535Li3 bb m 9

14、977774 0011027 7 m A-A-5 3 54 3 The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Metric Products. Products manufactured to metric dimensions will be considered on an eq

15、ual basis with those manufactured using inch-pound units, providing they fall within the tolerances specified using conversion tables contained in the latest revision of Federal Standard No. 376, and all other requirements of this document are met. If a product is manufactured to metric dimensions a

16、nd those dimensions exceed the tolerances specified in the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. Regulatory requirements. Federal Food, Drug and Co

17、smetic Act. If the product covered by this document has been determined bv the U.S. Food and Drua -a Administration to be under its jurisdiction, the offeror/ contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with the requirements of the Federal Food, Drug a

18、nd Cosmetic Act, as amended, and regulations promulgated thereunder. In addition, the offeror/contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with the requirements of all other applicable Federal, State, and local statutes, ordinances, and regulations. Rec

19、overed materials. The offeror/contractor is encouraged to use recovered material in accordance with Public Law 94-580, as amended, and as implemented by Federal Acquisition Subpart 23.4 to the maximum extent practical. Preservation, packaging, packing, labeling, and marking. Unless otherwise specifi

20、ed, preservation, packaging, and packing shall be to a degree of protection to preclude damage to containers and/or contents thereof under normal shipping conditions, handling, etc., involving shipment from the supply source to the receiving activity, plus reshipment from receiving activity, and sha

21、ll conform to applicable carriers rules and regulations. Intermediate and exterior package quantities and labeling and marking shall be as specified in the contract and/or order. 3 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-53543 bb = 7777

22、374 OOLL030 3 i A-A-5 3 5 43 NOTE1 document: The following National Stock Number is covered by this 6640-00-197-9878 BOTTLE SCREWCAP Orderin data. (Intermediae/exterior package quantities and &marking must be specified in the contract and/or order: MILITARY INPERESTS: Preparing Activity: Custodians

23、: Army - MD Navy - MS Air Force - 03 DoD-MB Agent: DLA-DM CIVIL AGENCY COORDINATING ACTIVITIES: PH8 Project No. 6640-3499 Location: Dick # 6 CID-BOTTLE-SCREWCAP 4 *V.S. GOVERNMENT PRINIING OFFICE: 1988 - 505433/92546 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-