DOD A-A-53920-1989 CAN PETRI CULTURE DISH《有盖培养皿铁罐》.pdf

1、A-A-53720 bb = 7777774 OOLLL72 7 A-A-539 2 O 20 June 1989 COMMERCIAL ITEM DESCRIPTION CAN, PETRI CULTURE DISH The General Services Administration has authorized the use of this commercial item description as replacement for Federal Specification GG-C-120a This commercial item description covers a co

2、rrosion-resistant steel Petri culture dish can with a lift-out rack. . Salient characteristics. Shall be a Petri culture dish can for holding 100 millimeter (mm) diameter size Petri culture dishes with covers. Shall be suitable for holding Petri culture dishes during a heat sterilization process, an

3、d for use as a sanitary dust- free storage container for the Petri dishes. Shall consist of cylindrical can with a telescoping lid and a lift-out rack that fits inside the can. The can, lid, and rack shall be made of corrosion-resisting steel that is polished with a No. 3 finish to facilitate cleani

4、ng. The can and lid shall be fabricated from a minimum No. 24 United States Standard Gage (.O25 inch thick) corrosion-resisting steel conforming to type 304 of ASTM Designation A 167. The seams of the can and lid shall be soldered with a non-toxic silver solder. Shall be supplied with a lift-out rac

5、k having the capacity to hold and stack 12-100 X 15 mm commercial designated size Petri dishes (with covers) or 15-100 X 10 mm commercial . designated size Petri dishes (with covers). The rack construction shall include a circular base with two vertical frame members. The lift-out rack shall be dime

6、nsioned to fit freely inside the cylindrical can. The base shall be fabricated from a minimum No. 22 United States Standard Gage (.O3125 inch thick) corrosion-resisting steel conforming to type 304 of ASTM Designation A 167. members shall be 1/2 inch wide minimum strip fabricated from a minimum No.

7、16 United States Standard Gage (.O625 inch thick) corrosion-resisting steel conforming to type 304 of ASTM Designation A 167. The vertical frame AMSC N/A FSC 6640 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. y THIS DOCUMENT CONTAINS $! PAGES. -T - Provided by IHS

8、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Shall be supplied with the cylindrical can having nominal body dimensions of nine (9) inches high and 4-1/2 inches diameter. The outside body of the can shall be encircled with a halfhound bead, located approximately

9、two (2) inches below the top edge, to serve-as a shoulder for the telescoping lid in closure. Shall be supplied with a lid cover that has a nominal three (3) inch height and an inside diameter that is dimensioned to provide a snug fit on the body of the-can in closure. The nomminal overall height of

10、 the assembled can (i.e. with telescoping lid in place) shall be ten (10) inches. WorkmanshiE. Lack shall be free from defects which detract from their appearance or impair their serviceability. - Unit. Each (EA). One can, with lid and rack as specified, constitutes one unit, The Petri culture dis-h

11、 can, lid cover and lift-out .Quality Assurance Provisions. Responsibility. for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance o all inspection requirements as specified herein. Except: as otherwise specified in the contrac

12、t or purchase order, the contractor may use his own or any facilities suitable or the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspe

13、ctions are deemed necessary to assure supplies and services conform to prescribed. requirements. the contractor shall be maintained by the contractor and made uvUIiLUuJ.b bv baAc. uvA4lll4 upuii b4Ae SviCfit5 eqGut, at riy time, or from time to time, during the performance of the contract and for a

14、period of three years after delivery of the supplies to which such records relate. I Records. Records of examinations and tests performed by or for .!“LI-. L. L1,- rn-*-L ,- In addition, the offeror/contractor shall comply, and be responsible for compliance by its subcontractoxs/suppI.iecs, with the

15、 requirements of all other applicable Federal, State, and local statutes, ordinances, and regulations. Recovered materials. The offeror/contractor is. encouraged to use recovered material in accordance with Public Law 94-580, as amended, and,ac implemented by Federal Acquisition Regulation Subpart 2

16、3,4-to the maximum extent practical. ,. . .- - .i_ 1 -. . . s. -. .- _i . 3 - - . . . -. .- . .i . - . I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - _ A-A-53920 bb W 7777774 0033335 2 W I- Other publications. The following documents form a par

17、t of this specification to the extent that is specified herein. Unless otherwise indicated, the effect on date of invitation for bids or I request for proposals shall apply. r. .% I AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) A-A-53 9 2 O Preservation, packaginq, p acking, labelinq, and markin

18、q. Unless otherwise specified, preservation, packaging, and packing shall be to a degree of protection to preclude damage to containers and/or contents thereof under normal shipping conditions, handling, etc., involving shipment from the supply source to the receiving activity, plus reshipment from

19、receiving activity, and shall conform to applicable carriers rules and regulations. Intermediate and exterior package quantities and labeling and marking shall be as specified in the contract and/or order. ASTM A167 Standard Specification for Stainless and Heat- Resisting Chromium-Nickel Steel Plate

20、, Sheet, and Strip. (Application for copies should be addressed to American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103). NOTE: The following National Stock Number is covered by this document: 6640-00-428-6050 Ordering data, (Intermediate/exterior package quantities a

21、nd labeling and marking must be specified in the contract and/or order) MILITARY INTERESTS: PREPARING ACTIVITY: DoD - MB Custodians : Army - MD Navy - MS Air Force - 03 Agent: DLA-DM CIVIL AGENCY COORDINATING ACTIVITIES: VA-OSS PHS Project No. 6640-1573 Location: CID/CAN/PITRI/S31/16 4 e Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-