DOD A-A-55708-1996 ROTATOR LABORATORY VARIABLE SPEED《实验室变速旋转体》.pdf

1、A-A- 55708 9 August 1996 - COMMERCIAL ITEM DESCRIPTION ROTATOR, LABORATORY, Variable Speed . The.Genera1 Services Administration has authorized the use of this Commercial Item Description for all Federal Agencies. 1. SCOPE. This Commercial Item Description covers a portable variable speed platform r

2、otator for use in a variety of laboratory procedures. 2. SALIENT CHARACTERISTICS: 2.1 The unit shall be a portable, variable speed, platform rotator for use in a variety of laboratory procedures including standard serological procedures. 2.2 The unit shall consist of a base and a top mounted platfor

3、m. 2.3 The unit shall have the nominal dimensions of 12 inches Wide by 13 inches Deep by 6 inches High. 2.4 The unit shall be equipped with: 2.4.1 A solid state speed control for selecting speeds in a nominal range of 80-210 rpms. 2.4.2 A 0-30 minute timer and a selector switch for timed or continuo

4、us operation. Beneficial comments, recommendations, additions, deletions, clarifications; etc. and any other data which may be used to improve this document should be sent to: Defense Personnel Support Center, Directorate of Medical Materiel, ATTN: DPSC-MBP, 2800 South 20th Street, Philadelphia, PA

5、19145-0530, by letter or usina the self-addressed Standardization Document Improvement d )Proposal, (DD Form 1426) appearinq at the end of this document. 1 FSC 6640 AMSC N/A DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction

6、 or networking permitted without license from IHS-,-,-A-A-55708 9993974 0172844 638 A-A- 5 5 7 O 8 2.4.3 A rimmed platform that is padded with a material that prevents labware from sliding during operation. The platform shall have nominal dimensions of 13 inches by 13 inches. 2.5 Workmanship. The la

7、boratory rotator shall be free from defects which detract from its appearance or impair its serviceability. 2.6 Unit. Each (EA). One laboratory rotator as specified, constitutes one unit. Each unit shall be packaged in accordance with the requirements of ASTM D 3951. 3. REGULATORY REOUIREMENTS. 3.1

8、Federal Food, Druq, and Cosmetic Act. If the product covered by this document has been determined by the U.S. Food and Drug Administration to be under its jurisdiction, the offeror/ contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with the requirements of t

9、he Federal Food, Drug and Cosmetic Act, as amended, and regulations promulgated thereunder. In addition, the offeror/contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with the requirements of all other applicable Federal, State, and local statutes, ordinance

10、s, and regulations. 3.2 Recovered materials. The offeror/contractor is encouraged to use recovered materials in accordance with the Federal Acquisition Regulation Subpart 23 -403 to the maximum extent practical. 4. QUALITY ASSURANCE PROVISIONS. 4.1 Product,Conformance. The products provided shall me

11、et the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the cornmercial market. The government reserves the right to require proof of such confor

12、mance. 4.2 Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units. Dimensions and tolerances specified shall be converted using conversion tables contained in the latest revision of ASTM E 380. 4.3 Market acceDt

13、abilitv. The following market acceptability criteria are necessary to document the quality of the product to be provided under this Commercial Item Description. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55708 A-A- 55708 9999974 0172845 57

14、4 4.3.1 The company producing the item must have been producing a product meeting the requirements of this Commercial Item Description for at least two (2) years. 4.3.2 The company must have sold 1,000 units meeting this Commercial Item Description in the commercial market place over the past two (2

15、) years. 4.4 Other aualitv assurance provision. Shall be as indicated in Section E, Inspection, of the contract and/or order. 5. PACKAGING. 5.1 Preservation, Dackacrincr packinq, labelinq and markinq. Shall be as specified in the contract and/or order. Specific requirements for this item are indicat

16、ed in Section C, Description/Specification; general packaging and marking requirements are indicated in Section D, Packaging and Marking. 6 NOTES. 6.1 National Stock Number Data. The following National Stock Number and its respective Item Identification is covered by this document : NATIONAL STOCK “

17、MBER ITEM IDENTIFICATION 6640-01-172-1132 ROTATOR , LABORATORY, Variable Speed., 120/230 volt, 50/60 Hz AC 6 6.2 Source of Documents: 6.2.1 Government Documents Defense Printing Service Detachment Office 700 Robbins Avenue Philadelphia, PA 19111-5094 . Bldg. 4D (NPM-DODSSP) 6.2.2 Non-Government Docu

18、ments. ASTM document s. (Applications for copies should be addressed to the American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. ) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-55708 m 4

19、 OL72B4b 400 m A-A- 55708 ANSI documents. (Applications for copies should be addressed to the American National Standards .Institute, 11 West 42nd Street, New York, NY 10036-8002. ) MILITARY INTERESTS: Preparing Activity: Custodians: DoD-MB Army - MD Navy - MS Air Force - 03 CIVIL AGENCY COORDINATING ACTIVITIES: VA-OSS USPHS FDA - MPQAS GSA-FSS-FCGC Agent : DLA-DM Project Number: 6640-1879 Location: ROTATC14.DOC (WORD 6) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-