DOD MIL-C-42068-1989 CHEST MEDICAL INSTRUMENT AND SUPPLY SET《医学器械供给装置柜》.pdf

1、MIL-C-42068 65 779970b 0267832 2 W C-7/-3? 25 June 1989 MILITARY SPECIFICATION CHEST, MEDICAL INSTRUMENT AND SUPPLY SET This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers three types of chests. Chests are

2、 equipped with two cover assemblies which convert to tables through the use of folding legs. 1.2 Classification. Chests covered by this specification shall be of the following types: Type I - Patient treatment and linen, with three compartments. Type II - Medicine and instrument, with six drawers. T

3、ype III - Medical instrument and supply set, with 9 fixed compartments. Beneficial comments (recommendations, additions, deletions) and1 IPersonnel Support Center, ATTN: Directorate of Medical Materiell IDPSC-RST, 2800 South 20th Street, Philadelphia, PA 19101, by I using the self-addressed Standard

4、ization Document Improvement I IProposal (DD Form 1426) appearing at the end of this document I AMSC/NA FSC 6545 lany pertinent data which may be of I Idocument should be addressed to: Headquarters, Defense I use in improving this lor by letter. I THIS DOCUMENT CONTAINS /d PAGES. Provided by IHSNot

5、for ResaleNo reproduction or networking permitted without license from IHS-,-,-2. APPLICABLE DOCUMENTS MIL-C-42068 65 m 9999906 0267833 4 m MIL-C-42068 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this

6、 document to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS Federal QQ-A-

7、200/9 QQ-A-250/8 QQ-A-250/11 TT-E-4 9 1 TT-P-659 PPP-B-6 3 6 Military MIL-P-116 MIL-L-10547 MIL-P-19834 STANDARDS Federal FED-STD-66 FED-STD-151 FED-STD-595 Aluminum Alloy 6063, Bar, Rod, Shapes, Aluminum Alloy 5052, Plate and Sheet Aluminum Alloy 6061, Plate and Sheet Enamel: Gloss, Synthetic (For

8、Metal and Primer Coating and Surfacer; Synthetic, Boxes, Shipping, Fiberboard Tube, and Wire Extruded Wood Furniture) Tints and White (For Metal and Wood Surfaces) Preservation, Methods of Liners, Case, and Sheet, Overwrap; Water- Vaporproof or Waterproof, Flexible Plate, Identification, Aluminum Fo

9、il, Adhesive Backed, Modification Applied Steel: Chemical Composition and Hardenability Metals: Test Methods Colors 2 O e e Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-C-42068 65 m 7797906 026983Y b m MIL-C-42068 Military MIL-STD-105 Sampli

10、ng Procedures and Tables for Inspection MIL-STD-129 Marking for Shipment and Storage MIL-STD-147 Palletized Unit Loads MIL-STD-794 Parts and Equipment, Procedures for Packaging by Attributes of (Unless otherwise indicated copies of federal and military specifications, standards, and handbooks are av

11、ailable from the Naval Publications and Forms Center, (ATTN: NPODS 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified

12、herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS Defense Personnel Support Center (DPSC) 25031 Chest Assembly, Medicine/Instrument 25032 Chest Assembly, Treatment/Linen 25033 Insert Sub-Assembly 25034 Table Top, Cover, Sub-Assembly 25035 Chest Assembly, Ut

13、ensil (Copies of drawings are available from the Defense Personnel Support Center, Directorate of Medical Materiel, DPSC-RST, 2800 So. 20th Street, Philadelphia, PA 19101-8419.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein (exc

14、ept for related associated detail specifications, specification sheets, or MS standards), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3 Provided by IHSNot for ResaleNo reprodu

15、ction or networking permitted without license from IHS-,-,-MIL-C-Li20bB b5 m 737770b 02b7B35 B m MIL-C-42068 3 . REQUIREMENTS 3.1 Materials. Except as specified herein, materials shall conform to the applicable portions of the specifications, standards, and drawings (with bills of material) shown in

16、 Section 2 of this specification, and shall be capable of meeting the requirements shown therein. In addition, the metals shall conform to the chemical requirements of their applicable specifications when tested as specified in 4.4.2. When materials to be used are not specifically designated, those

17、used shall be of the highest commercial quality, and suitable for the purpose intended . 3.1.1. Aluminum. 3.1.1.1 Sheet. Aluminum sheet of alloy 6061-T4 shall conform to QQ-A-250- Aluminum sheet of alloy 5052-H32 shall conform to QQ-A-250/8. 3.1.1.2 Tubing and angle. Aluminum alloy 6063-T5 shall be

18、used for tubing and angles, and shall conform to QQ-A-200/9. 3.1.2 Corrosion-resistinq steel. Corrosion-resisting steel shall be AISI 301 and 303 and shall comply with the AISI 300 series of FED-STD-66. 3.2 Style, design and construction. Style, design and construction shall be in accordance with th

19、e Defense Personnel Support Center (DPSC) Drawings referenced for each component. Each chest shall be supplied with two cover assemblies that can be used as tables through the use of folding legs. The completely assembled units shall be lightweight, and suitable for use with, and functionally compat

20、ible with the MUST system. The units shall be readily movable, simple to maintain and easy to clean. The drawers shall slide easily and smoothly. 3.2.1 Type I (Patient Treatment/Linen). The type I, Patient treatment/linen chest shall be furnished with 2 recessed carrying handles, 2 non-adjustable sh

21、elves, and 2 removable cover assemblies, and shall be in accordance with DPSC drawings No. 25032, 25033, 25034, and applicable Bill of Materials. The chest weight with shelves and covers shall not exceed 67 pounds. 4 . e a a Provided by IHSNot for ResaleNo reproduction or networking permitted withou

22、t license from IHS-,-,-MIL-C-q2068 65 D 7777706 0267836 T MIL-C-42068 3.2.2 Type II (Medicine and Instrument). The type II, Medicine and Instrument Chest shall be furnished with two recessed carrying handles, six drawers, two removable cover assemblies, and shall be in accordance with DPSC drawings

23、No. 25031, 25033, and 25034, and applicable Bill of Materials. The second drawer from the top shall have a built-in device for securing narcotics and other sensitive items. The chest weight with drawers and cover shall not exceed eighty-eight pounds. 3.2.3 Type III (Medical Instrument and Supply Set

24、). The type III, Medicine Instrument and Supply Set Chest shall be furnished _- - with two recessed carrying handles, nine fixed compartments and two removable cover assemblies, and shall be in accordance with DPSC drawings No. 25033, 25034, and 25035 and applicable Bill of Materials. The chest weig

25、ht with compartments and covers shall not exceed seventy-five pounds. 3.3 Chest outer covers. Chest outer covers (parts #3) shall be fabricated of either one or two pieces of 0.080 inch thick 6061-T4 aluminum welded with a cntinuous square-groove butt weld. A back-up strip may be used to facilitate

26、welding. Welds to be ground and finished smooth to blend with adjacent surfaces. 3.4 Drawer slides (Type II chest). The drawer glides on the type II chest shall be coated with nylon, 0.10 inch thick, applied by the fluidized bed process, as indicated on sheet 2 of drawing No. 25031. Necessary holes

27、shall be drilled after the coating process. 3.5 Finish. After welding has been completed, but before final assembly, all exposed metal surfaces of the chest except the drawer glide bottoms shall be furnished in hospital green color No. 14241 of Federal Standard No. 595. All surfaces shall be thoroug

28、hly cleaned of dirt, grease, welding flux and loose scale. Before painting, chests shall be primed with one coat of primer per TT-P-659, and two coats of enamel, class B, per TT-E-491. Brackets for the table legs shall be zinc plated prior to painting. The resultant finish shall be hard, smooth and

29、highly resistant to abrasion, chipping, cracking, acid, alkali, and solvents . 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-42068 65 W 979770b 0267837 1 W MIL-C-42068 3.6 Welding. appropriate equipment in a qualified process. be capable of

30、 developing the tensile strength of the parent metal. blend with the adjacent surfaces. a clean and workman-like manner. All welds shall be clean, nonporous, sound, ground and finished smooth to match adjacent surfaces. All welds shall be free from pitmarks and imperfection. All surfaces shall be fr

31、ee from sharp edges. Other welding shall be continuous on all surfaces, using welding rod of composition similar to parent metal, and suitable for the 3.7 Watertightness. specified in 4.4.1. chest . Welding shall be done by qualified welders using Spot welds shall All exposed spot welds shall be smo

32、othed sufficiently to All welds shall be finished in purpose intended. The finished chest shall be tested as There shall be no entry of water into the 3.8 Identification marking. Identification marking shall be permanently stamped on the chest or a metal nameplate shall be firmly attached to the che

33、st as shown in applicable drawing. following shall be permanently and legibly marked on the nameplate: National Stock Number Item Identification Contract or Purchase Order Number Manufacturers Name or Registered Trademark The A nameplate conforming to type I of MIL-P-19834 shall be considered accept

34、able. spotwelded to chest. 3.9 Workmanship. The complete chest and component parts shall be clean, well made, and free from defects which detract from their appearance or may impair their serviceability. Other types of metal nameplate shall be Workmanship shall be first class throughout. 4. QUALITY

35、ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purcha

36、se order, the contractor may use his own or any facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections ar

37、e deemed necessary to ensure supplies and services conform to prescribed requirements. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-420b 65 m 3999706 0267838 3 m a MIL-C-42068 4.1.1 Responsibility for compliance. All items shall meet all r

38、equirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that

39、 all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defect

40、ive material, either indicated or actual, nor does it commit the Government to accept defective material. 4.1.2 Records. Records of examinations and tests performed by or for the contractor shall be maintained by the contractor and made available to the Government, upon the Governments request, at a

41、ny time, or from time to time, during the performance of the contract and for a period of 3 years after delivery of the supplies to which such records relate. 4.1.3 Inspection. Inspection, as used in this specification, is defined as both examination (such as visual and auditory investigation withou

42、t the use of special laboratory appliances or procedures) and testing (determination by technical means of physical and chemical properties) of the item. 4.1.4 Certificates of quality. Certificates of quality supplied by the manufacturer of the component or material may be furnished in lieu of actua

43、l performance of such testing by the contractor, provided lot identity has been maintained and can be demonstrated to the Government. The certificate shall include the name of the contractor, the contract number, the name of the manufacturer or supplier, the National Stock Number (NSN), the item ide

44、ntification, the name of the component/material, the lot number, the lot size, the sample size, the date of testing, the test method, individual test results, and the specification requirements. 0 4.2 Sampling. 4.2.1 For examination. Sampling for examination shall be conducted in accordance with MIL

45、-STD-105 and table I. The unit of product for examination purposes shall be one chest. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-42068 65 m 7797906 02b9837 5 MIL-C-42068 TABLE I. Samplinq for examination. I I Inspection I AQL I I I I I

46、Type of Defect I Level* I (Percent Defective) I i For visual examination I I I Major defects I s-3 I 1.0 I Minor defects I s-3 I I I I I I For dimensional I I examination I s-2 I 2.5 4.0 I I I I *Minimum sample size shall be three (3). 4.2.2 For test. Sampling for precipitation test (see 4.4.1) shal

47、l be conducted in accordance with MIL-STD-105. The unit of product for examination purposes shall be one chest per lot and the acceptance number shall be zero. 4.3 Examination. The chests shall be examined for defects including, but not limited to, those listed in table II. TABLE II. Classification

48、of defects. I I I Icataqories I Defects I I I I I I I I I I I I I I I I I I Major 101 102 103 104 105 106 107 108 Minor I 201 I 202 I 203 I I 204 I 205 I I I 1 I I I I I I I I I I I I Covers do not seat or latch properly. I Drawers do not move smoothly in and out. I be lifted up to remove it from th

49、e frame. I Does not rest evenly on flat surface. I Any component missing or not as specified. I Materials non-conforming to specification. I I I I Covers not able to fold into tables as required.1 Drawer stops not positive so each drawer must I Lock drawer and lock not operating correctly. I Finish not free of burrs, scratches, dents. I Chest not free of sharp edges. I Identification marking not present, complete, I legible, correct. I Shel