DOT MIL-L-23091-1961 LEADS BUOY BATTERY《烛状导电棒 指引 指示浮标组》.pdf

1、MIL-L-23071 b1 W 9777706 0088777 8 W mbL-23 O9 1 (CC) 14 November 1961 _ Blitrtz Specification LEADS, BUOY BATTERY 1. SCOPE 1.1 Scope.= Thfa specification covexa olectrica leads used to interconnect lead acid 1w discharge type storage batteries muatad in racka in the highly cotrofve awsphere of elec

2、trical buop. 1.2 Crassification.= hads shall be of the folowing sires: size . Lenuth 7 1 0 14-inch 3 9 Sbi nch 4 75-inch 2. APPLICABLE Documms 2.1 The fo1lwing docwmnts, of the issue ia affect on data of invitation for bids, fom a part of this specification to the extent speci- fied herein: SPECIFIC

3、ATIO? Federal - *GZO1 had sheet STANDARD Mi fitary MtSTD.1129 Merking For Shipment And Storage (Copies of pecificationa and standards required by contractors - in connection with specific procurant functions ahould be obtaimd from the procuring activity or as directed by tho contracting officer.) PR

4、OBLEM HARD COPY Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - MIL-L-23091 61 W 9779906 0088798 T W .- MbL-23 09 1 (CO ) 3.1 Description.- Leads shall consist of BL single insulated red-flexible conductor, with terminals att6Ched to each end. 3.2

5、 Conductors.- Conductors for leads shall be wire size No. 8AWC with a minimtan of 35 and a maxiunam of 40 tinned strancn of copper wire. rubber interior cover. abrasion and to amnonia gas, hydrogen gas, salt water, oil, and other deteriorating $ubstaaces, acids, and alkalies, which may be encountera

6、d ia the interior of electric buoys, The insulation shall be a semi-hard rubber outer covering over a uoftar The insulation shall be highly resistant to 3.3 Terminals.- Tenninas shall be of solid lead confonnfng to Grade B of Specification QeG201. 3.4 Design and dimensions.- Design and dimnsioas of

7、leads shall conform to Figure 1. 3.4.1 Tubular area.- TerPinalr shall be provided with an inside tubular area which will permit assembly with a tight fit around insulation and No. 8AWG wire. 3.3 Mechanical strenRth.0 After aoeembiy laads shall show no Sig- of breakage or distortion when subjected to

8、 a pu .: of 300 pounds for one minute 3.6 orkmanship.= and shall ba free from burrs, sharp edger, and other imperfections which may impair servi ceabi lity. The leads shall be uniform in quality and shape, 4, QUALITY ASSUBANCE PROVISIONS 4.1 The supplier is responsible for the performance of all ins

9、pection requirements as specified herein. the supplier may utiliza his own or any other inspection facilities and services acceptable to the Goverament. Inspection records of the examination and tests shall be kept complete und avoilabla to the Coverrmient for the period of time specified in the con

10、tract or order. The Government reserves the right to perforai any of the inspections set forth in the specification where such inspections are deemed necessary fO assura oupplies and sedceo confonn to prercribed requiramntrh Ercept as otherwse specified, 4.2 I&.- Ali leads of the Iama site presentad

11、 at one tium shall ba considerad lot for purposar of iaopectioa and tarts. - - 2. PROBLEM HARD COPY Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Mi Gb23 09 1 (CC) 4.3 Samples for inspection.- Ten percent of the leads from each lot ahall be selecte

12、d at random for axamination. 4.4 1rrsvectfon.- Samples mlactsd ia accordance with 4.3 shall be inspected to verify compliance with all requirements of this specification. 4.5 Strain test samies.- Two leada from each lot, or one from each lot of less than fifty, shall be selected for the strain test.

13、 accordance with 6.5 shall be determined by means of freely banging weights or a suftabie testing machine. equipment by means other than by fasteners through the stud hole. shall withstand the pull specified in 3.5 without failure. 4.6 Strain test The mechanicaf strength of leads ssIected n Leads sh

14、all be firmly clamped to the test The leads 4.7 Rejection rate.- if defects are found in haif or more than half of the samples selected for examination, the entire lot shall be rejected. Failure of any strain test sample to pass the strain test of 4.6 shall be cause for rejection of the entire lot.

15、5. PREPARATION FOR DELIVERY 5.1 Preservation and packascinq.- Cleaning, drying, and packaging shall be in accordnce with the manufacturers comercial practice. Protection must be such as tu prevent deterioration during shipment and subsequent intervals preliminary to use. in a manner to ensure arriva

16、i at destination in satisfactory condition and which will be acceptable to the carriers at lowst rates. 5.2 Packinq.- The leads shall be packed or prepared for shipment 5.3 Markinq.- Interior packages and shipping containers shall be marked in accordance with Mflitary Standard MIGSTbl29. 6. NOTES 6.

17、1 Ordering data Procurement documents should specify the followingt (a) Title, number, and date of this specification. (b) Sizes required (see 1.2). 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-d MIL-L-23091 61 9777906 0088800 4 . HftL-2309 l(C

18、C) (e) Federal stock numbers. . - Notice.- When Government drawings, specifications, or other data are used for any purpose other than in connection with a definitely related CoverrPPrnt procurement operation, the United States Goverment thereby incurs no responsibility nor any obligation whatsoever

19、 and the fact tht the Goverment my have formulated, furnished, or in any way supplied the said drawings, apacfficstions? or other data io nof to be regarded by impiScation or otherwise as in any manuet licensing the holder or any other parson or corporation, or conveying any rights or permission to

20、manufacture, use, or rell any patented invention that play ia any way be rrlated thereto. PROBLEM HARD COPY Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-23071 b1 U 7779706 OOO1 b U MIGG23Wl (CC) 4 L A I I B SIZE 1 2 3 4 9/32 5/32 STUD HOU DUMETEE! 9/32 - CABLE SIZE 8 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-