DOT MIL-O-23641-1963 OUTLETS SHORE POWER《岸电引出线》.pdf

1、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2. APPLICABLE DOCUMENTS 2.1 invitation for bids, form a part; ofsthis specification to the extent specified herein: The following documents, of the issue in effect on date of SPECIFICATTONS Mi 1 i tary

2、MIGh14 - Molding Plastics and Molded Plastic Parts: Thermosetting JAN-P-100 - Packaging and Packing for Overseas Ship- ment, Ceneral Specification MJfrO-104 - Crates, Wood; Lumber and Plywood Sheathed, Nailed and Bolted MIL-P-15037 - Plastic Sheet, Laminated, Thermosetting, Glass-Cloth, Mlamine-Resi

3、n MILT-173 61 0 Circuit Breakers, Air, Electric, Insu- lated Enclosure 1 Federal 7 PPP-l3-585 - Boxes, Wood, Wirebound PPP-B-602 - Boxes, Wood, Cleated-Plywood PPP-B-62 1 - Boxes, Wood, Nailed and Lock-Corner PPP-b636 . - Box, Fiberboard PPPLC-843 - - Cushioning Material, Cellulosic PPP-T-60 - Tape;

4、 Pressure Sensitive Adhesive, Waterproof - for Packaging and Sealing STANDARDS Military MIbSp129 - Marking for Shipment and Storage Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-0-23b4L 57 m 7779706 0028LLO 7 -_- - .-_IC_ (Copies of specificati

5、ons required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Other publications.- The following commercial standards of the issue in effect on date of invitation for bids form a part of th

6、is speci- fication to the extent specified.herein. American Society of Testing Materials ASmA386 Zinc Coating (Hot-Dip) on Assembled Steel Products (Application for copies should be addressed to the American Society of Testing Materials, 1916 Race St., Philadelphia 3, Pa.) American Standards Associa

7、tion C37.13 - Low Voltage Air Circuit Breakers (Including Application Guide) C37.14 - Low Voltage Air Circuit Breakers, Test Code for C37. 16 - Schedule of Preferred Ratings for Alternating and Direct Current Low Voltage Air Circuit Breakers c37.17 - Preferred Pick-up Calibrations and Trip Delay Set

8、tings for Alternating Current Low Voltage Air Circuit Breakers (Application for copies should be addressed to the American Standards Association, 10 East 40th Street, New York 16, N. Y.) 3, REQUIREMENTS 3.1 Description.- The shore-power-outlet shall be an enclosed manually operated circuit-breaker w

9、ith a receptacle and receptacle plug for connection of the load cable, designed for outdoor installation on docks and constructed as indicated by Figure 1. receptacle cover, indicating light, operating handle shaft, and drain plugs shall be vaportight and watertight. ting type conduit entrance fitti

10、ng to provide a perfect water seal, as indicated in Figure 1. The enclosing cover, Provision shall be made for a pot- 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MILO- 23 641(c) 3.2 Electrical characteristics.- For alternating current installa

11、- tions the complete shore-power-outlet shall be capable of interrupting at rated voltage the 3-phase 60-cycle circuits of the applicable capacities shown in table I while under a 3-phase arcing fault at a power-factor of approximately 0.15 to 0.20 percent lagging., and, following such circuit inter

12、ruptions, the unit shall operate successfully for not less than three on-off cycles under rated volt,ge and current. TABLE I Int errnp t ing Capacities Class I Rating 1 - 15,000 Amperes at 600 V. A. C. Rating 2 - 25,000 Amperes at 600 V. A. C. Class II Rating 1 - 20,000 Amperes at 240 V. A. C. Ratin

13、g 2 - 30,000 Amperes at 240 V. A. C. Rating 3 - 50,000 Amperes at 240 V. A. C. Class III Rating 4 - 10,000 Amperes at 250 V. D. C. Rating 5 - 10,000 Amperes at 250 V. D. C. 20,000 Amperes at 250 V. D. C. Rating 6, 3.3 Material The material for each part shall be as specified Material not definitely

14、specified shall be of the best quality herein. used for the purpose in commercial practice. Material shall befree from oll defects and imperfections that might affect the serviceability of the finished product. quired wherever applicable. The use of “Everdur“ or equal bronze capscrews is re- 4. . -.

15、 i. -. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIG=23641(CG) 3.4 Construction.- The enclosure shall consist of a body and a cover. rous alloy or shall be fabricated of steel plate not less than 1/4-inch thick. Bodies fabricated of steel plate

16、 shall be seam welded. The -top edge of the body shall have a flange not less than l=l/ the circuit shall provide approximately 25 watts heat-dissipation. The switch shall be closed automatically by the opening of the circuit- . breaker, and opened by the closing of the circuit-breaker. shall be pro

17、vided with either a green lens and a heavy metal guard or a neon pilot light with a aolor option. for relamping from the exterior of the enclosure. dication shall be plainly visible in the area in front of the operating end of the outlet. resistant metal, or shall be suitably coated to resist corros

18、ion. The pilot light Lens and guard shall be removable The-pilot light in- All metal parts shall be made of suitable corrosion- 3.6 Operatiny, mechani_.- The operating mechanism of the power- outlets shall be of either the toggle switch type or the push-pull iiTU - handle type as shown on Figure 1.

19、swittch type, it shall be designed for haixl operation-but shall be suffi- ciently rugged to withstand foot operation, self-lubricating or shall be accessible for haricl lubricating as necessary and shall be easily renewable. shall be mads of corrosion-resisting mta1 or shall be suitably coated to r

20、esist,corrosion. - If tlic iiechanicm is OE the toggle All wearing parts shall be The.opc.mcin2 handle and all other parts - 3.7 -Watertightness.- Outlets shall sliow no leakage when tested as tipecified in 42.h. 3.8 Lubrication and-adiustment.- The shore-power-outlet shall be properly Lubricated an

21、d adjusted ready for operation. .-= i - - . fi- * Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_c_ MIL-0-23641 59 9999906 0021115 m MIL- the nameplate and designation shall be wear and corrosion resistantr The voltage and current ratings shall be

22、indicated on each receptacle and plug in a permanent manner that will resist wear aad corrosion. identification plate of corrosian-resistant steel or other suitable non- corrosive material shall be affixed to the body of the shore-power outlet: in a place where it will not interfere with the outlets

23、 normal operation. The identification plate shall contain the following information. An a* OUTLET, SHORE POWER b. Type and rating ce Federal stock number d. Manufaceurerfs name e. Contract No. and date $. U. S. Coast Guard 4. QUALITY ASSURANCE PROVISIONS 4,i Thc supplier is responsible for the perfo

24、rmance of all inspec- tion requirements as specified herein. Except as otherwise specified, the supplier may utilize his own or any other inspection facilities and ser- vices acceptable to the Government. inspection records of the examination and tests shall be kept complete and available to the Gov

25、ernment as speci- fied in the contract: or order, The Government reserves the right to perform any of the inspections cet forth in the specification where such inspections are deemed necessary to assure suppl%es and services conform to prescribed re qu irem nt s. 4*2 Examination.- All shore-power-ou

26、tlets shall be subject to a thorough examination to insure conformance to the requirements of this specification. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4.2.1 Heater and i-ndicator test9- Each unit shall be electrically connected on -the lin

27、e side and tests performed to prove satisfactory operation of the heaters and indicating light. 4.2.2 Safety interlock teste- The safety interlock feature on each , unit shall be operated to prove that the load plug cannot be engaged or disengaged with the circuit-breaker closed. trically operated,

28、powkr must be pyovided to prove its satisfactory opera- tion. If the safety lock is elec- 4.2.3 Circuit breaker test.-Each circuit breaker shall be manu- ally opened and closed a sufficient number of tims to prove satisfactory operation. compressed air at 3 pounds per square inch gauge for not less

29、than 5 minutes while completely submerged in a tank of water. 4.2.4 Watertightness teste- Each outlet shall be tested by applying 4.2.5 Weight test.- Each unit shall be shipped crated and the weight shall be obtained or each size or rating. 5. PREPARATION FOR DELIaRY 5.1 Domestic shipment.- 5.1.1 Im

30、mediate use.- The equipment shall be preserved, packaged, and prepared for shipment in such manner as to insure arrival at destina- tion in a satisfactory condition, and which will beacceptable-. to carriers at lowest rates. o 5.1.2 Storage.- 5.1.2.1 Preservation and packaging.- Equipment shall be p

31、reserved and packaged as specified for overseas shipment. 5.1.2.2 Packing.- Equipment shall be packed in domestic type woad- cleated plywood boxes, nailed wood boxes, or wirebound wood boxes, confor- ContenWshall be cushioned, blocked, and braced to prevent movement within boxes -ng-to Specification

32、s.PPP-B-61, PPP-B-621, and PPP-B-585$ respectively. 5.2 Overseas shipment.- 5.2.1 Preservation and Packaging.- -+ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - - . I MIL-0-23643 57 9799706 0028117 I I 5*2.1.1 Power i)utlet*- The incoming line op

33、ening shall be sealed with pressure-sensitive tape, !type I, Class i, conforming to specification PPP-T-60. shall be removed and its cover replaced. The bulb and the receptacle-plug shall be wrapped separately in cushioning material conforming to Specifica- tion PPP-C-843 and packed together with th

34、e outlet unit in a fiberboard box conforming to Specifcation PPP-b636. The receptacle cover shall he secured in place. The lamp bulb 5,2,2 Packin%.- Equipment shall be packed in overseas type cleated plywood boxes, nailed wood boxes, or wirebound boxes, conforming to Speci- fications PPP-?3-601, MIL

35、-C-104, or PPP-B-585-respectively, Contents shall be cushioned, blocked and braced in accordance with Specification JANCP-100. 5*3 contract or order, interior packages and shipping containers shall be marked in accordance with Standard MIL-STD-129. ,hrkinq.- in addition to any special marking requir

36、ed by the The approved item name is “OUTLETS 8 SHOI and the fact.that the Government may have formulated, furnished, or in any way supplied the said drawings, specifications, or other data is not to be regarded by in+ plication or otherwise as in any mannerlicensing the holder or any other person or

37、 corporation, or conveying any rights or permlssion to manufacture, use, or, sell any patented invention that may in any way be related thereto. Preparing Activity: U. S, Coast Guard i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DIM. TO SUIT CONDUCT ENTRANCE FLANGE OPTIONAL CIRCUIT WEAKER GASKET, OPERATING HANDLE 7 A- l D E b l E W MOUNTING HOLE Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-