ECA 520CA00-A-1992 Blank Detail Specification for Special-Use Sensitive Switches of Certified Quality.pdf

1、Reproduced By GLOBAL ENGINEERING DOCUMENTS With lha Pmnisrion of IA Unda Royalty Areemmt 4 I O O 5 O cv In I a i ANSI/EIA-52OCAOO-A-1992 APPROVED: Aprll 20, 1992 EIA S P ECI FI CATI ON Blank Detail Specification for Special-Use Sensitive Switches of Certified Quality (Revision of EU-52OCAOO) MAY 199

2、2 ELECTRONIC INDUSTRIES ASSOCIATION ENGINEERING DEPARTMENT EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the p

3、urchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of EIA from manufacturing or selling products not conforming to such Standards and Publications, n

4、or shall the existence of such Standards and Publications preclude their voluntary use by those other than IA members, whether the standard is to be used either domestically or internationally. I Recommended Standards and Publications are adopted by EIA in accordance with the American National Stand

5、ards Institute (ANSI) patent policy. By such action, EiA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Recommended Standard or Publication. This EIA Standard is considered to have International Standardization implication, but t

6、he international Electrotechnical Commission activity has not progressed to the point where a valid comparison between the EIA Standard and the IEC document can be made. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. i

7、t is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. Published by ELECTRON IC IN DUSTRIES ASSOCIATION Engineering Department 2001 Pennsylvania Ave. N.W., Washington, D.C.

8、 20006 PRICE: Please refer to the current Catalog of EIA - electrical ratings; - functional operation; - operating characteristics; - strength of actuator; - voltage proof, Values shall be stated for the following characteristics when the following conditions exist (mandatory if applicable): altitud

9、e voltage proof when an altitude rating is declared. gauging when gauging dimensions are declared. logic level endurance when a logic level rating is declared, low level endurance when a low level rating is declared, immersion in cleaning solvents when tenninals are declared suitable for PC mounting

10、. low temperature operation when the low temperature rating is lower than OC, overload when the electrical ratings exceed 6 volts and 0.5 ampere, strength of mounting bushing when the switch is intended to be mounted by a threaded bushing, strength of screw mounting when the switch is intended to be

11、 mounted by screws, solderability when the terminals are declared to be solderable. All other ratings and characteristics are optional. Ratings and characteristics that are not applicable shall be listed as not applicable. E EIA-520CAO0-A Page 3 Generic specification number Electronic components of

12、certified quality in accordance with 31 Outline drawing - maximum enclosure dimensions ( ,. angle of projection) IOTES 1 See figure . for ful dimensional requirements 2 Dimensions are denoted as follows: or insert not applicable) insert test duration or “not applicable“ (insert applicable or not app

13、licable) (insert seal grade or unsealed) (insert acceleration and g value, or insert not applicable) (insert low and high temperature, or insert not applicable) C (insert values) O c to O (insert acceleration, g value and frequency range; or insert not applicable) (insert applicable or not applicabl

14、e) (insert special circuit and detent characteristics if applicable) (insert applicable or not applicable) (insert maximum value if required) (insert values(s) of force and travel. Strength of: -actuator -mounting bushing -screw mounting -termination Seal Solderability 1.2.4 Electrical characteristi

15、cs Actuator grounding Altitude voltage proof Contact bounce Contact chatter Electrical overload Endurance -electrical(insert -logic level -low level -mechanical(insert Insulation resistance Switch resistance -millivolt level -specified current -rated load Temperature rise Voltage proof EIA-52OCAOO-A

16、 Page 5 insert force or torque value insert torque value or insert “not applicable“ insert torque value or “not applicable“ insert “22.5 or “45 if applicable insert type of seal according to 4.14 or 4.15 of EIA-5200000 or %ot app 1 icab 1 e insert “app licab le“ or “not app 1 icab le“ insert maximum

17、 resistance or “not applicable“ insert value of test voltage or “not ap p 1 ic ab 1 e I insert maximum duration or “not applicable insert maximum duration or “not applicable“ insert “applicable“ or “not applicable“ test type) insert cycles of operation and any other required test details insert cycl

18、es of operation or “not applicable“ insert cycles of operation or “not applicable test type) insert cycles of operation or “not applicable“ insert minimum resistance and the associated test voltage or “not applicable“ insert I Q . maximum“ or “not applicable“ insert Q maximum“ or “not app licableT i

19、nsert I Q maximum“ or “not applicable“ insert “30C max“ or “not applicable“ insert value of test voltage EIA-520CAOO-A Page 6 1.3 Part number EIA 520CA00-A 72 m 3234b00 0501634 4 m 5 Switches covered by this detail specification shall be described by the following in the order shown: a) bi The EIA p

20、ublication number for this detail specification. (insert and describe additional categories as required) Example of EIA part number: EIA520CAXXinsert) EIA520CA (insert) (describe) 1 number of the detail specification number of this blank detail specification NOTE: THIS WCUMENT MAY PROVIDE PAT NUMBER

21、S IN EXCESS OF 15 DIGITS. DEPARTMENT OF DEFENSE USERS ARE CAUTIONED TO CHECK THE USEABILITY OF THESE PART NUMBERS IN THEIR APPLICATION IN ACCORDANCE WITH DOD POLICY, 1.4 Marking The marking of the switch and package shall be in accordance with the requirements of 2.5 of EIA 1020-1. (Insert the detai

22、ls of marking on the switch and on the package, including any special marking requirements,) 1.5 Ordering information Orders for switches covered by this specification shall contain the following information as a minimum: a) the applicable part number according to 1.3; b) “In accordance with EIA-520

23、C000-(X), (XI edition“ (Insert the number and edition of the detail specification); c) when certified records of released lots are required, include “CERTIFIED RECORDS REQUIRED“, 1.6 Certified records of released lot Insert the information required by EIA-5200000, 1.7 Additional information (not for

24、 inspection purposes) 1.7.1 Safety Considerations The user shall consider the suitability of the switch with regard to any safety requirements applicable to the equipment. 1.8 Increased severities or requirements that are additional to those specified in the generic and/or sectional specification. N

25、OTE - Additional or increased requirements should be specified only when essential. EIA 520CA00-A 92 m 3234600 0503635 b m - - EIA-520CA00-A Page 7 1.9 a2 2.1 2.2 2.3 2.4 2.5 Common features See 7 on page 1. Inspection requirements Structurally similar devices Insert principles of structural similar

26、ity for the type covered. Preconditioning Qualification approval inspection Qualification approval inspection requirements shall be in accordance with table 1 in EIA-520C000 with all details and requirements specified in the detail specification, Quality conformance inspection Quality conformance in

27、spection is prescribed in table 1 for lot-by-lot inspections and in table 2 for periodic inspections. For visual examination, the clarification of major and minor defects shall be as follows: (insert description of defects), Sampling procedure details. Table 1 - Test schedule for lot-by-lot inspecti

28、on Test number and test designation (see Note 1) GROUP A ( nonde s truc t ive ) 1-1 Visual examination major minor 2-1 Switch resistance 1-5 Functional operation 3-1 Voltage proof 1-6 Operating characteristics AQL 1 .o 4.0 1 .o 1 .o 1 .o 1 .o Notes l The paragragh number of the test and performance

29、requirements refer to the generic specification for electromechanical switches, EIA 5200000, with the supplementary requirements specified in this specification. 121 In this table: IL= inspection level AQL= acceptable quality level 3 The appropriate test method shall be specified in the detail speci

30、fication, m. EIA 520CA00-A 92 3234b00 050Lb3b 8 W Test number and test EIA-52OCAOO-A Page 8 Conditions Sample size, sample description, Performance of & criterion of acceptability requirements designation 1 test il: (see Note 1) (see Note 1) GROUP B (destructive ) 11-1 Solderability ( destructive 1

31、8-1 Electrical endurance (see note 2) 4-1 Temperature rise 3-1 Voltage proof GROUP D (destructive ) I12 36 (Requaiification per Table I (see Note 1) n I sampledescription I t I I l I ll NOTES : il The number of the test and performance requirements refer to the generic specification for electromecha

32、nical switches, EIA 5200000, with the supplementary requirements specified in this document, In the groups, all specimens shall be subjected to the required tests and all tests shall be performed in the sequence shown, 2 The electrical endurance test shall be limited to the maximum current rating at

33、 standard atmospheric conditions. 31 In this table: n = sample size t = total acceptance criterion (permitted number of defectives for one or several groups combined e.g. Group O, Group 1, Group 2 to Group 6 inclusive). p = periodicity in months. 141 When the detail specification includes additional

34、 tests, additional test groups may have to be added. EIA 520CA00-A 92 m 3234b00 0503637 T m EA STANDARD AND SPCIFICATONNUMBERING Standard or Generic Specification Standard Prefix for all Numbers Sectional Specification Designator Blank Detail Specification Designator -TJ- a STANDARD A document that

35、establishes engineering and technical requirements for processes, procedures, practices and methods that have been decreed by authority or adopted by consensus. Standards may also be established for selection, application and design criteria for material. Standards and other documents not in the spe

36、cification format use only the IA basic numbering system as follows: EIA-123 Original Standard EIA-123-1 Addendum to Original Standard EIA-123-A First Revision of original Standard incorporating all Addenda SPECIFICATION A document prepared specifically to facilitate procurement which clearly and ac

37、curately describes the essential technical requirements for purchased material. Procedures necessary to determine that the requirements for the purchased material covered by the specification have been met shall also be referenced or included. EIA 1230000 EIA 123A000 EIA 123AAOO EIA 123AAAA EIA 123O

38、OAA is a Generic Specification is a Sectional Specification is a Blank Detail Specification is a Detail Specification is a Detail Specification for which no Sectional or Blank Detail Specification was issued. NOTES: I. Some older specifications may not have been converted to this numbering system. 2. See EP-11 “Guide for the Preparation of Specification Using IECQ-System Format,“ for more detail.