ECA 520EA00-1989 Blank Detail Specification for In-Line Switches《直插式开关的空白详细规范》.pdf

1、Q O O cv In I w 5 0 ANSI/ElA-520EA00-$989 APPROVED: January 23, 1989 EIA SP ECI FI CATION Blank Detail Specif cation for In-line Switches EIA-520EA00 MARCH 1989 ELECTRONIC IN DUSTRI ES ASSOCIATION ENGINEERING DEPARTMENT AoDroved For Use In itie NECQ Svstem EIA 520EA00 89 3234600 0073593 O NOTICE EIA

2、 Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the pro

3、per product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or non-member of EIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such standards and Publications pre

4、clude their voluntary use by those other than EIA members, whether the standard is to be used either domestically or internationally. Recommended Standards and Publications are adopted by EIA without regard to whether or not their adoption may involve patents on articles, materials, or processes. By

5、 such action, EIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Recommended Standard or Publication. This EIA Specification is considered to have international standard- ization implication, but the International Electrotechnica

6、l Commission activity has not progressed to the point where a valid comparison between the EIA standard and the IEC document can be made. This Specification does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of

7、the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From EIA Standards Proposal No. 2869, formulated under the cognizance of the P-13.4 Subcommittee on DIP and Miscellaneous Switches.) Approved f

8、or use in the NECQ System as NQ-EIA-520EA00. Copyright 1989 Published by ELECTRONIC INDUSTRIES ASSOCIATION Engineering Department 1722 Eye Street, N.W. Washington, D.C. 20006 All rights reserved Printed in U.S.A. PRICE: $10.Q0 I .-. -. EIA 520EA00 89 = 3234600 0073594 2 = Introduction: I EIA-520EA00

9、 Page 1 Blank Detail Specification For In-line Switches A blank detail specification is a supplementary document to the Sectional Specification and contains requirements for style, layout and minimum content of detail specifications. Detail Specifications not complying with these requirements shall

10、not be considered as being in accordance with the certification system nor shall they be so described. In the preparation of detail specifications, the content of Subclause 2.6 of the Sectional Specification shall be taken into account. A detail specification shall cover a particular type of in-line

11、 switch construction and may include several styles for that type. It is preferable that all styles of a particular type of in-line switch construction be contained in a single detail specification wherever possible. Different construction types shall not be contained in the same detail specificatio

12、n. The detail specification shall state directly, or by reference to other documents, all information necessary to completely describe all interchangeability parameters for that type of in-line switch, including any styles, and to ensure conformance thereof with all requirements for quality assessme

13、nt. 0 The pages following this introduction and instruction illustrate a detail The numbers between brackets correspond to the following information specification. which shall be inserted in the positions indicated: Identification of the detail specification (i) The standards organization under whos

14、e authority the detail specification is drafted. (2) The number of the detail specification, date of issue. (3) The number and issue of the Generic Specification. (4) The number and issue of the Sectional Specification. (5) The number and issue of the IEC Blank Detail Specification. (6) A short desc

15、ription of the type of in-line switch which shall include as a minimum the information needed for listing on the Qualified Products List. See Appendix A. (7) (8) Information on the typical construction (when applicable). A circuit diagram or short description of the electrical circuit(s). (9) Applic

16、ation(s) covered and/or assessment level. 9 EIA 520EA00 89 3234600 O073595 4 EIA-520EA00 Page 2 An outline drawing containing the maximum enclosure dimensions. When space permits, the drawing may include detailed dimensions also. The specification number and the title may be shown here. This is opti

17、onal since it repeats front page information. The introduction and the information shown are mandatory. Following the introduction, the scope and object shall be given. The information shown is mandatory. Additional information may be added as necessary. The information shown is mandatory. Any addit

18、ional information which supplements Section Two of EIA-5200000 shall be given in this section. The paragraph numbers shall correspond with the paragraph numbers of EIA-5200000. New paragraph numbers shall be assigned for headings not included in EIA-5200000. EXAMPLE : The related documents, units, s

19、ymbols, terminology, standard values, preferred values, and marking are prescribed in Section Two of EIA-5200000 and the following additional requirements. 2.3 Terminology : Additional terminology is defined in Appendix A herein. 2.9 Part Numbering: Each switch described by this detail specification

20、 has been assigned a discrete part number. The part numbering system is described in Appendix B herein. The information shown is mandatory. Any additional information which supplements a combination of Section Three of EIA-5200000 and Section Three of the Sectional Specification shall be given in th

21、is section. The paragraph numbers shall correspond with the paragraph numbers of EIA-5200000. New paragraph numbers shall be assigned for headings not included in EIA-5200000. The information shown is mandatory. Any additional information which supple-ments Section Four of EIA-5200000 and Section Fo

22、ur of the Sectional Specification shall be given in this section. The paragraph numbers shall correspond with the paragraph numbers of EIA-5200000. New paragraph numbers shall be assigned for headings not included in EU-5700000. The detail specification shall include a table, based upon Table 1 of E

23、IA-5200000, which is complete and sufficient for qualification approval inspection and which substantiates compliance of all optional in-line switch features with the performance requirements. The detail specification shall include a table, based upon Appendix A of this specification, which is compl

24、ete and sufficient for lot-by-lot and periodic inspection. EIA 520EA00 89 m 3234600 0073596 6 m - EIA-520EAOO Page 3 I GENERIC SPECIFICATION NUMBER (3) ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDANCE WITH (4) I OUTLINE DRAWING DETAIL SPECIFICATIOb NUMBER (2) BLANK DETAIL SPECIFICATION NUMBEF

25、; (5) PRODUCT DESCRIPTIOh (6) ELECTRICAL CIRCUIT (7) TYPICAL CONSTRUCTIOh (8) APPLICATION/ ASSESSMENT LEVEL (9) I 1 INFORMATION ON THE AVAILABILITY OF THE COMPONENTS QUALIFIED TO THIS SPECIFICATION IS GIVEN IN I THE QUALIFIED PRODUCTS LIST EIA 520EA00 89 323LbOO 0073597 8 EIA-520EA00 Page 4 (12) INT

26、RODUCTION This detail specification was prepared by (enter rmre of Ccrrrmiittee, mufacturer or -1 Note: -tail Specifications are to confom with all requirementc specified in its blank detail specification, sectional cpecification and generic specification. (13) SECTION ONE - SCOPE AND OBJECT 1.1 Sco

27、pe The (applicable modifiers to describe subfamily of in-line switches) switches of certified quality covered by this detail specification: 1. have maximum enclosure dimensions of (maximum length, width, and height dimensions). 2. have a maximum rated voltage of (highest rated voltage of subfamily).

28、 3. have a maximum rated current of (highest rated current of subfamily). 4. (other) 1.2 Object: a The object of this detail specification is to provide all information required for the identification, quality assessment; and certification of -these switches. The information, contained herein or by

29、reference, is complete and sufficient for inspection purposes. (14) SECTION TWO - GENERAL The related documents, units, symbols, terminology, standard values, preferred values, and markings are prescribed in Section Two of EIA-5200000. (15) SECTION THREE - QUALITY ASSESSMENT PROCEDURES The quality a

30、ssessment procedures are prescribed in Section Three of EIA-5200000 and are supplemented by the following information. 3.1.1. Qualification Approval Inspection Tests: The qualification approval inspection tests are prescribed in Table I herein for the qualification of the entire subfamily of switche

31、s covered by this Detail Specification. 3.4.6 Lot-by-Lot Inspection Tests: The lot-by-lot inspection te,sts are prescribed in Table II herein. (If the sequence of tests is not optional, the detail specification shall specify the mandatory test sequence.) 3.4.7 Periodic Inspection Tests: The periodic

32、 inspection tests are also prescribed in Table III herein. - 5- EIA 520EA00 89 W 3234600 0073598 T EIA-520EA00 Page 5 (16) SECTION FOUR - TEST METHODS AND REQUIREMENTS The test methods andrrequirements are prescribed in Section Four of EIA-5200000 and are supplemented by the following information. (

33、See instruction. As a minimum, the detail specification shall prescribe all details of test required by the basic test methods, RS-448 etc., for the following tests. ) 1-1 1-2 1-4 2- 1 2-5 3- 1 11-1 4.9 8 2- 1 2-5 3- 1 Visual Examination Dimensional Examination Mass Switch Resistance Insulation Resi

34、stance Voltage Proof Solderability Strength of Terminations Electrical Endurance Switch Resistance Insulation Resistance Voltage Proof (17) Table I - Qualification Approval Inspection Tests (18) Table II - Lot-By-Lot and Periodic Inspection Tests (19) Table III - Periodic Inspections Tests EIA 520EA

35、00 89 = 3234b00 0073599 L , EIA STANDARD AND SPECIFICATION NUMBERING STANDARD A document that establishes engineering and technical requirements for processes, procedures, practices and methods that have been decreed by authority or adopted by consensus. Standards may also be established for selecti

36、on, application and design criteria for material. Standards and other documents not in the specification format use only the EIA basic numbering system as follows: EIA-123 Original Standard EIA-123-1 Addendum to the Original Standard EIA-123-A First Revision of original Standard incorporating all Ad

37、denda SPECIFICATION A document prepared specifically to facilitate procurement which clearly and accurately describes the essential technical requirements for purchased material. Procedures necessary to determine that the requirements for the purchased material covered by the specification 6 have be

38、en met shall also be referenced or included. k EIA Specifications use the following system: Standard or Generic Specification Indicator Standard Prefix for all Numbers Sectional Specification Designator i- Blank Detail Specification Designator A - A - Detail Specification Designator EIA 1230000 is a

39、 Generic Specification EIA 123A000 is a Sectional Specification EIA 123AA00 is a Blank Detail Specification EIA 123AAAA is a Detail Specification EIA 12300AA is a Detail Specification for which no Sectional or Blank Detail Specification was issued NOTES 1. Some older specifications may not have been converted to this numbering system. 2. See EP-11, “Guide for the Preparation of Specifications Using IECQ-System Format,I1 for more detail. c:) - -