ECA 520EAAB-1989 Detail Specification for Machine Insertable Dual In-Line Switches of Certified Quality《已质量认证的机器双列直插交换的详细规范》.pdf

1、4 e e m a i$ O I a 6 EIA 520EAAB 89 = 3234600 0073563 2 W /- . ANSI/ EIA- 52 OEAAB-198 9 APPROVED: May 26, 1989 EIA SPECIFICATION Detail Specif cation for Machine Insertable Dual In-Line Switches of Certified Quality EIA-520EAAB XINE 1989 ELECTRONIC INDUSTRIES ASSOCIATION ENGINEERING DEPARTMENT Appr

2、oved For Use In The NECQ System I I EIA 520EAAB 89 3234600 00735b4 4 W NOTICE EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products,

3、and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or non-member of EIA from manufacturing or selling products not conforming to such Standards

4、 and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than EIA members, whether the standard is to be used either domestically or internationally. Recommended Standards and Publications are adopted by EIA without regard to whether o

5、r not their adoption may involve patents on articles, materials, or processes. By such action, EIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Recommended Standard or Publication. This EIA Specification is considered to have i

6、nternational standardization implication, but the International Electrotechnical Commission activity has not progressed to the point where a valid comparison between the EIA standard and the IEC document can be made. This Specification does not purport to address all safety problems associated with

7、its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (APPROVED FOR USE IN THE NECQ SYSTEM AS NQ-EIA-520EAAB) Copyright

8、 1989 Published by ELECTRONIC INDUSTRIES ASSOCIATION Engineering Department 1722 Eye Street, N.W. Washington, D.C. 20006 PRICE: $10.00 All rights reserved Printed in U.S.A. IA 520EAAB 89 m 3234600 0073565 b m EIA-520EAAB .- . ELECTRONIC INDUSTRIES ASSOCIATION 2001 EYE STREET, N.W. WASHINGTON, D.C. 2

9、0006 GENERIC SPECIFICATION NUMBER EU-5200000 ELECTRONIC COMPONENTS OF ASSESSED OUALITY IN ACCORDANCE WITH . OUTLINE DRAWING 1. Original dimrioar are inchei. 2. The configuration ir optional within the limti of the rpecified dimeiuioru. ETAIL SPECIFICATION NUMBER 3IA-520EAAB BLANK DETAIL SPECIFICATIO

10、N NUMBER EIA-520EA00 RODUCT DESCRIPTIOh DUAL-IN-LINE PACKAGE (DIP) SWITCH, SLIDE ACTUATED, MACHINE INSERTABLE. MULTIPLE SPST STATIONS ELECTRICAL CIRCUIT SEE CIRCUIT DIAGRAM TYPICAL CONSTRUCTION PLASTIC HOUSINGS AND ACTUATORS APPLICATION/ ASSESSMENT LEVEL I INFORMATION ON THE AVAILABILITY OF THE COMP

11、ONENTS I I OMLIFIED TC THIS SPECIPICATICN IS !mm II. I THE OUALIFIED PRODUCTS LIST i P, EIA 520EAAB 89 m 3234600 0073566 8 m s- I 2.0 SECTION TWO - GENERAL EIA-52OEAAB Page 1 DETAIL SPECIFICATION FOR MACHINE INSERTABLE DUAL IN-LINE SWITCHES OF CERTIFIED QUALITY Introduction (From EIA Standards Propo

12、sal No. 2197, formulated under the cognizance of the EIA P-13.4 Subcommittee on In-Line and Miscellaneous Switches.) The complete requirements forthe switches describedherein shall consist of this Detail Specification, the latest issue of EIA-520E000, “Sectional Specification for In-Line Switches of

13、 Certified Quality,“ and the latest issue of EIA-5200000, “Generic Specification for Special-use Electromechanical switches of Certified Quality. It 1.0 SECTION ONE - SCOPE AND OBJECT 1.1 Scope The Dual In-line Machine Insertable Switches of certified quality covered by this Detail Specification: 1.

14、1.1 Have maximum enclosure dimensions of 32.5 mm (1.280 inch) long, 7.26 (0.286) wide and 4.57 (0.180) high. 1.1.2 Have a maximum rated voltage of 50 Vdc. 1.1.3 Have a maximum rated current of 100 mA. 1.1.4 Have slide actuators that are flush with, or recessed below, the top surface of the switch. 1

15、.1.5 Are sealed against the entrance of soldering flux and cleaning solutions during the process of assembly to circuit boards. 1.2 Object The object of this Detail Specification is to provide all information required for the identification, quality assessment, and certification of these switches. T

16、he information, contained herein or by reference, is complete and sufficient for inspection purposes, 2.1 The related documents, units, symbols, terminology and markings are prescribed in Section Two of Sectional Specification EIA 520E000, and General Speci- fication EIA 5200000, and the following a

17、dditional requirements: 2.5.1 Switches shall be marked so as to identify the state of the contacts with respect to the actuation position (e.g., “ON“ on appropriate side, a round dot on the closed contact side, etc.). I 7 EIA 520EAAB A 3234b00 U073567 T W EIA-52OEAAB Page 2 2.5.2 Pari Number: Switch

18、es shall be identified as follows: Type number from Table IV This Detail Specification number TABLE IV 3.0 SECTION THREE - QUALITY ASSESSMENT PROCEDURES 3.1 The quality assessment procedures are preseribed in Section Three or Sectional Specification EIA 520E000, and are supplemented by the following

19、 information: 3.1.1 Qualification Inspection Tests: The qualification tests are prescribed in Table 1 herein for the qualification of the entire subfamily of switches covered by this Detail Specification. Qualification switches must have 8 poles. 3.4.5 Lot-By-Lot Inspection Tests: The lot-by-lot ins

20、pection tests ara prescribed in Table II herein. 3.4.6 Periodic Inspection Teats: The periodic inspection tests are prescribed in Table III herein. 4.0 SECTION FOUR - TEST METHODS AND REQUIREMENTS 4.1 General The test methods and requirements are prescribed in Section Four of Generic Specification E

21、IA 5200000, Section Four of Sectional specification EIA 520E000, and are supplemented by the following information: 4.1.6 Switches with tape top seals shall be supplied with contacts in the closed position and seals in place for Group A, the solderability test of Group B, and the machine soldering t

22、est of Group C of Qualification Test Table I. These seals may be removed for all other qualification tests. Insulation resistance and voltage proof measurement in Group A only will be made between adjacent poles (the closed circuit prevents taking these readings aeroas open contacta). EIA 520EAAB 89

23、 3234600 0073568 L EIA-52OEAAB Page 3 4.5.1 4.5.2. 4.6.1 4.8.1 4.9.1 4.11.1 4.19 4.24 Switch Resistance Contact resistance is to be measured between the two terminals associated with each switch pole, and shall not exceed 20 milliohms initially and in Qualifiction Groups A and C, and 100 milliohms i

24、n QualificationGroups B, D, E and Periodic Test Group B. Insulation Resistance Insulation resistance shall be measured at 100 +, 5 Vdc, and at stan- dard atmospheric conditions. Insulation resistance shall not be less than 1000 megohms. Voltage Proof Voltage proof measurements shall be made with an

25、applied voltage of 500 Vac (rms) . Maximum allowable leakage current is 500 microamperes. The switch shall withstand the test voltage without sustained arcing, breakdown, or damage to insulation. Vibration Vibration testing shall be in accordance with EIA 186-8 Type III. Strength of Terminations Str

26、ength of terminations shall be tested in accordance with EIA-186-6 with a 1.1 pound- load on a minimum of three randomly selected terminals on each specimen. Electrical Endurance The electrical endurance test shall be run with one-half of the specimens tested in accordance with Test 8-4 (logic load)

27、 and one-half of the specimens tested in accordance with Test 8-5 (low level load). The number of cycles shall be 2000, and no sticks or misses are allowed. Capacitance The maximum allowable capacitance shall be 5 picof arads. Machine Soldering The machine soldering test shall be run in accordance w

28、ith EIA-448-2 Method 16 and with Method A fluxing (touching body), a soldering time of no less than four seconds, and cleaning by immersion and spray.(all four solutions in each case). After the test, there shall be good solder connections, no externally visible indication of leakage, contact resist

29、ance shall be in accordance with 4.5.1, and insulation resistance shall be in accordance with 4.5.2, and all marking shall be readable. - EIA 520EAAB 89 3234b00 13073569 3 - EIA-52OEAAB Page 4 TABLE I: QUALIFICATION APPROVAL INSPECTION TESTS Test Method & Group Group A Visual Examination Dimensions

30、Mass Switch Resistance Insulation Resistance Voltage Proof Group B Solderability Strength of Terminations Electrical Endurance Switch Resistance Voltage Proof Group C Machine S older in g Visual Examination Switch Resistance Insulation Resistance Group D Thermal Shock Vibration Visual Examination Sh

31、ock Visual Examination Switch Resistance Voltage Proof Group D Capacitance Moisture Resistance Switch Resistance Voltage Proof Test No, 1- 1 1-2 1-4 2- 1 2-5 3- 1 11-1 See 4.9 See 4.11.1 2- 1 3- 1 See 4.24 1-1 2- 1 2-5 10-2 5- 3 1- 1 5-2 1-1 2- 1 3- 1 17-1 10- 1 2- 1 3- 1 M/WS M M M M M M M - M M M

32、M M M M M M M M M M M M M M M M M M M M M D /ND ND ND ND ND ND ND D D D ND ND D ND ND ND D D ND D ND ND ND ND D ND ND t.s. Al 1 (1) (1) All All All 10 24 10 10 t.d - O O O O O O 1 1 1 1 1 g.d O 1 1 O O EIA 520EAAB 89 m 3234600 0073570 T m - EIA-52OEAAB Page 5 Test Method & Group Group A (Lot-By Lot)

33、 TABLE II: LOT-BY-LOT INSPECTION TESTS Assessment Level C Test No. - D/ND - IL A94 Visual Examination Major Minor Switch Resistance Insulation Resistance Voltage Proof 1- 1 ND 2- 1 ND II 1% 2-5 ND 3- 1 ND Test Method & Group Test No. Table III: PERIODIC INSPECTION TESTS Group B (every 12 months) Sol

34、derability 11-1 Strength of Terminations See 4.9 Electrical Endurance See 4.11.1 Switch Resistance 2- 1 Voltage Proof 3- 1 Group C (every 36 months) Requalification Table I t.d. g.d. - t.s. - D /m 20 1 D D D ND ND - EIA 520EAAB 89 3234600 0073573 3 W EIA-52OEAAB Page 6 KEY : M= mandatory test D= des

35、tructive test ND = nondestructive test t.s. = minimum quantity of test specimens t.d. = maximum permissible number defective units per test g.d. = maximum permissible number of defective units per group NOTES : (1) = A minimum of 2 pieces of each configuration covered by the Detail Specification. -

36、- EIA 520EAAB 89 m 3234b00 0073572 3 m - f EIA STANDARD AND SPECIFICATION NUMBERING (7 STANDARD A document that establishes engineering and technical requirements for processes, procedures, practices and methods that have been decreed by authority or adopted by consensus. Standards may also be estab

37、lished for selection, application and design criteria for material. Standards and other documents not in the specification format use only the EIA basic numbering system as follows: EIA- 12 3 Original Standard EIA-123-1 Addendum to the Original Standard EIA-123-A First Revision of original Standard

38、incorporating all Addenda SPECIFICATION A document prepared specifically to facilitate procurement which clearly and accurately describes the essential technical requirements for purchased material. Procedures necessary to determine that the requirements for the purchased material covered by the spe

39、cification have been met shall also be referenced or included. EIA Specifications use the following system: ._ EIA123AAA Standard or Generic Specification Indicator Standard Prefix for all Numbers Sectional Specification Designator Blank Detail Specification Designator Detail Specification Designato

40、r A L EIA 1230000 is a Generic Specification EIA 123A000 iS a Sectional Specification EIA 123AA00 is a Blank Detail Specification EIA 123AAAA is a Detail Specification EIA 12300AA is a Detail Specification for which no Sectional or Blank Detail Specfication was issued NOTES 1. Some older specifications may not have been converted to this numbering system. Using IECQ-System Format,“ for more detail. ! 2. See EP-11, “Guide for the Preparation of Specifications % - o