ECA 580BA00-1997 Blank Detail Specification Fixed Metallized Electrode Film Dielectric AC Capacitors.pdf

1、b Blank Detail Specification: Fixed Metallized Electrode Film Dielectric O O m O dD In I lu a - ANSU EIA- 58 OBAO 0-199 7 Approved: August 27, i997 EIA I SPECIFICATION AC Capacitors EIA-580BA00 OCTOBER 1997 ELECTRONIC INDUSTRIES ASSOCIATION ENGINEERING DEPARTMENT NOTICE EIA Engineering Standards and

2、 Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his partic

3、ular need. Existence of such Standards and Publications shall not in any respect preclude any member or non-member of EIA fiom manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use

4、by those other than EIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by EIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, EIA does not assume any liability to any patent

5、 orner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Specification is considered to have International Standardization implication, but the International Electrotechnical Commission activity has not progressed to the point where a valid compari

6、son between the EIA Specification and the IEC document can be made. This Specification does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Specification to establish appropriate safety and hea

7、lth practices and to determine the applicability of regulatory limitations before its use. prom Standards Proposal No. 2804, formulated under the cognizance of EIA P-2.2 Subcommittee on Plastic and Paper Dielectric.) Published by QELECTRONIC INDUSTRIES ASSOCIATION 1997 Engineering Department 2500 Wi

8、lson Boulevard Arlington, VA 22201 PRICE: Please refer to the current Catalog of EM, JEDEC, and TIA STANDARDS and ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1-800-854-7179) In terna t ional (303-397-7956) All rights reserved Printed in U.S.A. EIA-5 SOBA00 FIXED CA

9、PACITORS PART : Blank Detail Specification: Fixed metallized electrode film dielectric AC capacitors - Assessment level F Introduction to a Blank Detail Specification A blank detail specification is a supplementary document to the Sectional Specification and contains requirements for style and layou

10、t and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they be so described. In the preparation of detail specification the content of 1.4 of the sectional specificatio

11、n shall be taken into account. The numbers between brackets on the first page correspond to the following information which shall be inserted in the position indicated. Identification of the detail specification: 1) The International Electrotechnical Commission (IEC) or the national standards organi

12、zation (NSO) under whose authority the detail specification is drafted. 2) The IEC or NSO number of the detail specification, date of issue and any further information required by the national system. 3) The number and issue of the IEC or NSO specification. 4) The IEC number of the blank detail spec

13、ification. Identification of the capacitor: 5) A short description of the type of capacitor. 6) Information on typical construction (when applicable). NOTE-When the capacitor is not designed for use in printed board applications, this shall be clearly stated in the detail specification in this posit

14、ion. -z- STD-EIA 5OBAUU-ENGL 1997 = 3234b00 05853b7 312 EIA-580BA00 7) Outline drawing with main dimensions that are of importance for interchangeability andor reference to the national or international documents for outlines. Alternatively, this drawing may be given in an appendix to the detail spe

15、cification. 8) Application or group of applications covered and/or assessment level. NOTE-The assessment level(s) to be used in a detail specification shall be selected from the sectional specification subclause, 3.5.4. This implies that one blank detail specification may be used in combination with

16、 several assessment levels, provided the grouping of tests does not change. . 9) Reference data on the most important properties, to allow comparison between the various capacitor types. EM-58OBAOO Page 1 SECTION ONE - GENERAL DATA 1 General data 1.1 Mounting Recommended method) of mounting (to be i

17、nserted) (see 1.4.2 of ). 1.2 Dimensions Table 1 Dimensions (in millimeters, or millimeters and inchez Case O A B A B size code NOTES 1 when there is no case size reference. Table 1 may be omitted and the clmensions given in table 2, which then becomes table 1. The dimensions shall be given as maxim

18、um dimensions or nominal dimensions with a tolerance. 2 1.3 Ratings and characteristics Capacitance range Tolerance on rated capacitance Rated voltage(s) (See table 2) Rated AC RMS voltage (and frequency Fdifferent from 50/60 Hz) - Rated peak (pulse) voltage (if applicable) Category voltage (if appl

19、icable) (See table 2) EIA-580BA00 Page 2 Rated Peak current capacitance PF Climatic category Rated Peak current capacitance PF Rated case temperature Tangent of loss angle (Frequency . . .) Leakage current (terminal-to-case) Rated peak current or rated voltage pulse slope, dU/dt, if applicable Sinus

20、oidal rated AC current (at reference frequency .) and derating curve versus temperature (if applicable). Table 2-Values of capacitance, AC voltage and peak current (or voltage pulse slope), related to case sizes k Rated AC voltage (Ur Category AC voltage (Ut?)* Case size reference * If different fro

21、m the rated voltage. I Table %Particular characteristics 1.4 Related documents Generic specifications: IEC Publication 384-1 (1982): Fixed Capacitors for use in Electronic Equipment, Part 1 : Generic Specification Amendments No. 1 (1985) and No. 2 (1987) EIA-5 8 OB AO0 Page 3 Sectional Specification

22、: IEC Publication QC (199J: Part : Fixed Metallized Electrode Film Dielectric AC Capacitors. 1.5 Marking The marking of the capacitor and the package shall be in accordance with the requirements of IEC Publication QC : PaK-4 subclause 1.6. NOTE-The details of the marking of the component and the pac

23、kage shall be given in full in the detail specification. 1.6 Ordering information Orders for capacitors covered by this specification shall contain, in clear or in coded form, the following minimum information: a) Rated capacitance b) Tolerance on rated capacitance c) Rated AC voltage at 50/60 Hz d)

24、 Number and issue reference of the Detail Specification. e) Rated case temperature 1.7 Certified records of released lots Requiredhot required 1.8 Additional information (not for inspection purposes) 1.9 Additional or increased severities or requirements Additional or increased severities or require

25、ments to those specified in the generic and/or sectional specification. NOTE-Additions or increased requirements should be specified only when essential. EIA-5 SOBA00 Page 4 Conditions of test (see note 1) SECTION TWO - INSPECTION REQUIREMENTS IL AQL (see note 2) S-4 2.5% 2 Inspection requirements 2

26、.1 Procedures 2.1.1 For qualification approval, the procedures shall be in accordance with the sectional specification, IEC Publication QC : part- subclause 3.4. 2.1.2 For Quality Conformance Inspection, the test schedule (table 4) includes sampling, periodicity, severities and requirements. The for

27、mation of inspection lots is covered by 3.5.1 of the Sectional Specification. I Subclause number and D test (see note 1) Group A inspection subgroup A 1 (lot-by-lot) ND Subgroup A2 1N-D 4.4 Dielectric withstand voltage 4.5 Capacitance I 4.6 Dissipation factor I I II 1.0% As in 4.4.1 and 4.4.4 Freque

28、ncy: 60E I Frequency: 6Or I Temperature: 90 OC air FC Duration: 10 min &er case reaches 85 OC Performance Requirements (see note 1) As in 4.2.3 As specified in table 1 this specification. Legible marking and as specified in 1.5 of this specification As in 4.4.5 and 4.4.5.1 As in 4.5.1 As in 4.6.1 No

29、 evidence of leakage of the impregnant IL AQL Performance Requirements (see note 2) (see note 1) 30pAmaximum I S-3 2.5% Periodicity sample size acceptance (see note 3) Pn c Performance requirements (see note 1) Frequency: 60 Hz Frequency: 60 Hz As in 4.5.1 As in 4.6.1 . EIA-5 8 OB AO0 Page 5 Subclau

30、se number and test (see note 1) D or ND - - D Conditions of test (see note 1) 4.8 Leakage current 1 15 VAC 60 Hz applied terminal to case Group B inspection subgroup B 1 (lt-by-lot) 4.1 1 Solderability Tin-lead solders with noncorrosive fluxes and normal soldering techniques. Good tinning as evidenc

31、e by free-flowing of the solder with wetting of the terminations. 4.12 Terminalstrength Torque plus axial compression and pull. As in 4.12.1 - D or ND - ND Subclause number and test (see note 1) Conditions of test (see note 1) Group C inspection (periodic) subgroup C 1 A Pari of sample of subgroup c

32、1 6 9 11 4.1 Dimensions (detail) As specified in table 1 of this specdcation. 4.13.1 Initial measurements Capacitance Tangent of loss angle Dielectric withstand voltage As in 4.4.1 and 4.4.4 I I As in 4.4.5 and 4.4.5.1 4.9 Vibration EU RS- 186, method 7 type III with no electrical load I As in 4.9.1

33、 and meet 4.2.3 plus I 4.4 Subgroup C 1B part of sample of subgroup C 1 6 18 1 . EIA-580BA00 Page 6 Subclause number and test (see note 1) Conditions of test or (see note 1) Periodicity sample size acceptance (see note 3) Pn c Performance requirements (See note 1) 4.13.1 Initial measurements Capacit

34、ance I Frequency: 60 &- As in 4.5.1 Tangent of loss angle Asin4.6.1 Frequency: 60 & As in 4.4.5 and 4.4.5.1 Dielectric withstand voltage 4.7.2 Low-temperature As in 4.4.1 and 4.4.4 No evidence of leakage of the impregnant Temperature: 40 “C to room No cycles: 2 Cycle: 24 h 40 “C then 24 h at RT I 23

35、 “C to 40 “C 4.15.1 Low-temperature capacitance change Subgroup C 1 combined sample of subgroup C 1 A and ClB Capacitance change withm i 2% to - 5% of 23 “C value 6 27 2 DI 4.13 Humidity As in 4.13.3 &d 4.13.4 EL4 RS- 186, Capacitance Tangent of loss angle 4.13.3 Final measurements Capacitance chang

36、e within 2% of initial values. Must meet values in 4.6.1 - As in 4.4.5 and 4.4.5.1 Dielectric withstand voltage Subgroup C2 DI 6 15 1 4.1 O Salt spray AS 4.10.1 - LeSS than 5% Of area with finish failure. EIA RS- 186 method 5 type II D 125% rated voltage 10 “C above rated temperature 2000 h 381 Subg

37、roup C3 4.17 High-temperature life test As in 4.17.6 EIA-5 80B AO0 Page 7 D Conditions of test Periodicity 3 In this table: P = Periodicity (in months) N = Sample size C D = Destructive ND = Nondestructive IL. AQL RT = Room temperature DF = Dissipation factor = Acceptance criterion (permitted number

38、 of defectives) = Inspection level per IEC Publication 4 1 O = Acceptable quality level per EC Publication 4 1 O 4 In the case of more than one endurance test, the detail specification may change the periodicity in such a way that only one endurance test is carried out every 3 months. 5 If one defec

39、t occurs, a second endurance test shall be carried out after which no defects are permitted. . Standard or Generic Specification Standard Prefix for all Numbers Sectional Specrfication Designator Blank Detail Specification Designator 3- STD-EIA SBOBAOO-ENGL 1777 = 3234bU0 U585375 479 9 EIA STANDARD

40、AND SPECIFICATION NUMBERING STANDARD A document that establishes engineering and technical requirements for processes, procedures, practices and methods that have been decreed by authority or adopted by consensus. Standards may also be established for selection, application and design criteria for m

41、aterial. Standards and other documents not in the specification format use only the IA basic numbering system as follows: IA-1 23 Original Standard EIA-123-1 Addendum to Original Standard EIA-123-A First Revision of original Standard incorporating all Addenda SPECIFICATION A document prepared specif

42、ically to facilitate procurement which clearly and accurately describes the essential technical requirements for purchased material. Procedures necessary to determine that the requirements for the purchased material covered by the specification have been met shall also be referenced or included. EIA

43、 Specifjcations use the following system: EIA 1230000 EIA 123A000 EIA 123AAOO EIA 123AAAA EIA 123OOAA is a Generic Specification is a Sectional Specification is a Blank Detail Specification is a Detail Specification is a Detaii Specification for which no Sectional or Blank Detail Specification was issued. NOTES: 1. Some older specifications may not have been converted to this numbering system. 2. See EP-I 1 “Guide for the Preparation of Specification Using IECQ-System Format,“ for more detail. .