ECA EIA-198-3-4-F-2009 Ceramic Dielectric Capacitors Classes I II III and IV - Part III Detail Specification Sheets - Section 4 Radial Through-Hole Capacitor Conformally Coated and.pdf

1、 ANSI/EIA-198-3-4-F-2009 Approved: March 3, 2009 EIA STANDARD Ceramic Dielectric Capacitors Classes I, II, III and IV Part III: Detail Specification Sheets Section 4: Radial Through-Hole Capacitor, Conformally Coated and Molded Types EIA-198-3-4-FEIA-19(Revision of EIA-198-3-4-E) 8-3-4-F MARCH 2009

2、EIA Standards Electronic Components Association NOTICE EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purch

3、aser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of EIA from manufacturing or selling products not conforming to such Standards and Publications, nor s

4、hall the existence of such Standards and Publications preclude their voluntary use by those other than EIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by EIA in accordance with the American National Standards Institute (A

5、NSI) patent policy. By such action, EIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is considered to have International Standardization implication, but the International Electrotechn

6、ical Commission activity has not progressed to the point where a valid comparison between the EIA Standard and the IEC document can be made. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of th

7、e user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5153 formulated under the cognizance of the P-2.1 Ceramic Capacitors Standards Committee). Published by: ELECTRONIC C

8、OMPONENTS ASSOCIATION 2009 EIA Standards and Technology Department 2500 Wilson Boulevard Suite 310 Arlington, VA 22201 PRICE: Please call: Global Engineering Documents, USA and Canada (1-800-854-7179) http:/ All rights reserved Printed in U.S.A. PLEASE ! DONT VIOLATE THE LAW! This document is copyri

9、ghted by the EIA and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: Global Engineering Documents 15 Inverness Way East Englewood, CO 80112-5704 or call USA and

10、Canada (1-800-854-7179), International (303-397-7956) EIA-198-3-4-F Page 4 EIA Detail Specification Sheet Ceramic, Radial Through-Hole, Conformally Coated and Molded Types Figure 1. Ceramic, Radial Through-Hole Figure 2. Ceramic, Radial Through-Hole, Conformally Coated Capacitor Dimensions Molded Ca

11、pacitor Dimensions Radial Through-Hole Body Dimensions Size Identifier W Max. Millimeters (Inches) H Max. Millimeters (Inches) T Max. Millimeters (Inches) S Millimeters +0.76 (Inches +0.030) SH Max. Millimeters (Inches) D Millimeters +0.10/-0.03 (Inches +0.004/-0.001) Radial Through-Hole, Conformall

12、y Coated - 15 - 20 - 30 - 40 - 50 3.81 (0.150) 5.08 (0.200) 7.62 (0.300) 10.16 (0.400) 12.70 (0.500) 3.81 (0.150) 5.08 (0.200) 7.62 (0.300) 10.16 (0.400) 12.70 (0.500) 2.54 (0.100) 3.18 (0.125) 3.81 (0.150) 3.81 (0.150) 5.08 (0.200) 2.54 (0.100) 2.54 (0.100) 5.08 (0.200) 5.08 (0.200) 10.16 (0.400) 4

13、.75 (0.187) 5.84 (0.230) 8.38 (0.330) 12.07 (0.475) 13.46 (0.530) 0.51 (0.020) 0.51 (0.020) 0.51 (0.020) 0.64 (0.025) 0.64 (0.025) Radial Through-Hole, Molded Size Identifier Case Width W Millimeters (Inches) Case Length L Millimeters (Inches) Case Thickness T Millimeters (Inches) Lead Space C Milli

14、meters (Inches) Lead Diameter M Millimeters +0.102/-0.025 (Inches +0.004/-0.001) - 05 - 06 - 07 - 08 4.83 0.254 (0.190 0.01) 7.37 0.254 (0.290 0.01) 12.19 0.51 (0.480 0.020) 12.19 0.51 (0.480 0.020) 4.83 0.254 (0.190 0.01) 7.37 0.254 (0.290 0.01) 12.19 0.51 (0.480 0.020) 12.19 0.51 (0.480 0.020) 2.2

15、9 0.254 (0.90 0.01) 2.29 0.254 (0.90 0.01) 3.56 0.25 (0.140 0.010) 6.10 0.25 (0.240 0.010) 5.08 0.381 (0.200 0.015) 5.08 0.381 (0.200 0.015) 10.16 0.51 (0.400 0.020) 10.16 0.51 (0.400 0.020) 0.642 (0.025) 0.642 (0.025) 0.642 (0.025) 0.642 (0.025) 1) Original (design) dimensions in inches. 2) Other s

16、izes, lead spacings, and lead styles are available consult suppliers. MWWT TLLCCMMax: 1.14 mm(0.045”)Min: 31.75mm(1.25”)Min: 31.75 mm(1.25”)DStraight Leads Formed Leads Crimped Leads30Ref.SSSSHTLLWTHEIA-198-3-4-F Page 5 EIA Detail Specification Sheet Ceramic, Radial Through-Hole, Conformally Coated

17、and Molded Types 1 Requirements Type: Radial Through-Hole capacitors, conformally coated and molded, with ceramic dielectric and solderable leads. Dimensions and Configuration: per Figures 1 and 2. Available Characteristics: C0G (NPO), X7R, Z5U, and Y5V. Operating Temperature Range: per Table 1. Dis

18、sipation Factor (or Q): per Table 1 in accordance with EIA-198, Part II, Method 101 (or 102). Dielectric Strength: 250% of rated voltage in accordance with EIA-198, Part II, Method 103. Insulation Resistance: per Table 1 in accordance with EIA-198, Part II, Method 104. Body Insulation: 500V DC in ac

19、cordance with EIA-198, Part II, Method 103. Capacitance Values, Tolerances and Voltages: Style _ TableConformaly Coated 3 Molded 4 Solderability: Both leads shall be simultaneously evaluated per J-STD-002. Resistance to Soldering Heat: Per EIA-198, Section II, Method 302. Terminal Strength: In accor

20、dance with EIA-198, Section II, Method 303, Test Condition A, 2.2 kg minimum pull to destruction. Resistance to Solvents: For marked components, per EIA-198, Section II, Method 310. No deterioration in marking legibility is permitted. Vibration: Per EIA-198, Section II, Method 304. Environmental Req

21、uirements: 1. The temperature coefficient of capacitance or characteristics as shown in Table 1 shall be as specified in EIA-198, Section I. 2. When seal-tested per EIA-198, Section II, Method 209, capacitors shall meet the capacitance change, the dissipation factor (or Q), and insulation resistance

22、 requirements of Table 1. 3. When life-tested per EIA-198, Section II, Method 201, the units shall meet the capacitance change, the dissipation factor (or Q), and insulation resistance requirements of Table 1. 4. Moisture resistance per EIA-198, Section II, Method 204. 5. Thermal Shock: Per EIA-198,

23、 Section II, Method 202. EIA-198-3-4-Page 6F EIA Detail Specification Sheet Ceramic, Radial Through-Hole, Conformally Coated and Molded Types Table 1. Characteristics of and Requirements for Ceramic Radial-Leaded Capacitors Maximum DF (or Q) Minimum Insulation Resistance 2Characteristic Operating Te

24、mperature Range, C TCC Maximum Capacitance Change Post Seal or Life Test Initial Post Seal or Life Test Initial Post Seal or Life Test C0G (NPO) -55 to +125 30 ppm/C 0.3% or 0.25pF 10.1% (or 1000) 0.5% (or 200) X7R -55 to +125 15% 20% 2.5% 3% 100 G or 1000 M-F 10 G or 100 M-F Y5V -30 to +85 -82 %, +

25、 22% 30% 5% 7% 10 G or 100 M-F 1 G or 10 M-F Z5U +10 to +85 -56 %, + 22% 30% 4% 5% 10 G or 100 M-F 1 G or 10 M-F 1/ Whichever is greater, 2/ Whichever is less. 2 Part Number Guidelines and Product Availability Each manufacturer defines a unique part numbering format for the products covered by this

26、specification. Therefore, there is no specific part numbering format defined in this document. In many cases, the size identifier or “series” portion of the part number will be preceded by one or more alphanumeric characters unique to that specific manufacturer. The EIA Codes in Part 1, which identi

27、fy capacitance, and tolerance, as defined in Table 2, are strictly adhered to across the industry. The method for identifying other variables is typically supplier choice. Table 2 below, provides general guidelines on availability of Radial Through-Hole products within the industry. Tables 3 and 4 d

28、efine the capacitance values and tolerance availability by size identifier and TCC at the time of this revision for conformally coated and molded products respectively. Table 2. Ceramic, Radial-Leaded, General Availability Size Identifier TCC Capacitance Tolerance Voltage 05 06 07 08 15 20 30 40 50

29、C0G (NPO) X7R Z5U Y5V EIA Code (refer to Part I) B = + 0.1 pF C = 0.25 pF D = 0.50 pF F = 1% G = 2% J = 5% K = 10% M = 20% Z = -20%, +80% 50 100 200 EIA-198-3-4-F Page 7 EIA Detail Specification Sheet Ceramic, Radial Through-Hole, Conformally Coated and Molded Types Table 3. Radial Through-Hole, Con

30、formally Coated Range Chart TCC C0G (NPO) X7R Z5U Y5V Size Identifier Working DC Voltage Available Capacitance Available Tolerance Available Capacitance Available Tolerance Available Capacitance Available ToleranceAvailable Capacitance Available Tolerance 15 50 100 200 10 pF 2.2 nF 10 820 pF 1.0 820

31、 pF B, C, D, F, G, J, K 100 pF 100 nF 100 pF 22 nF 100 pF 22 nF J, K, M 10 47 nF 10 nF - - - M, Z 10 220 nF 10 100 nF - - - M, Z 20 50 100 200 1.0 pF 10 nF 1.0 pF 6.8 nF 1.0 pF 3.9 nF B, C, D, F, G, J, K 1.0 nF 1.0 F 1.0 nF 1.0 F 1.0 47 nF J, K, M 10 nF 1.0 F 10 220 nF - - - M, Z 330 1.0 F 150 220 n

32、F - - - M, Z 30 50 100 200 1.0 pF 220 nF 1.0 pF 100 nF 1.0 pF 3.3 nF B, C, D, F, G, J, K 100 pF 3.3 F 100 pF 1.0 F 100 pF 220 nF J, K, M 6.8 nF 3.3 F 6.8 1.0 F 1.0 2.2 nF M, Z - - - - - - - - - - - - 40 50 100 200 470 pF 68 nF 470 pF 47 nF 470 pF 18 nF F, G, J, K 4.7 nF 2.7 F 4.7 nF 1.0 F 4.7 470 nF

33、 J, K, M 10 nF 4.7 F 10 nF 22 F 10 100 nF M, Z - - - - - - - - - - - - 50 50 100 200 39 68 nF 33 56 nF - - - F, G, J, K 1.0 4.7 F 330 nF 2.2 F 100 390 nF J, K, M 1.0 4.7 F 1.0 2.2 F - - - M, Z - - - - - - - - - - - - EIA-198-3-4-F Page 8 EIA Detail Specification Sheet Ceramic, Radial Through-Hole, C

34、onformally Coated and Molded Types Table 4. Radial Through-Hole, Molded Range Chart TCC C0G (NPO) X7R Z5U Size Identifier Working DC Voltage Available Capacitance Available Tolerance Available Capacitance Available Tolerance Available Capacitance Available Tolerance 05 50 100 200 1.0 pF 8.2 nF 1.0 p

35、F 4.7 nF 1.0 pF 2.7 nF B, C, D, F, G, J, K 100 pF 150 nF 100 pF 68 nF 10 pF 15 nF J, K, M 10 pF 390 nF 10 pF 220 nF - - - M, Z 06 50 100 200 10 22 nF 5.6 22 nF 1.5 10 nF D, F, G, J, K 100 pF 1.0 F 100 pF 68 nF 100 pF 15 nF J, K, M 470 nF 1.0 F 270 470 nF - - - M, Z 07 50 100 200 2.2 4.7 nF 2.2 100 n

36、F 2.2 100 nF D, F, G, J, K 5.6 nF 2.2 F 5.6 nF 2.2 F 5.6 nF 3.3 F J, K, M 100 nF 4.7 F 100 nF 2.2 F - - - M, Z 08 50 100 200 120 150 nF 100 180 nF 5.6 100 nF F, G, J, K 560 nF 1.0 F 2.7 3.9 F 3.9 4.7 nF J, K, M 5.6 10 F 2.7 3.3 F - - - M, Z EIA-198-3-4-F Page 9 EIA Detail Specification Sheet Ceramic

37、, Radial Through-Hole, Conformally Coated and Molded Types Revision History Spec # - Rev Description of Changes Pages Date EIA-198-3-4-E General: Repaginated as separate document. Various 3/28/97 EIA-198-3-4-E General: Added references to test methods in Part. Various 3/28/97 EIA-198-3-4-E Changed A

38、C to CC Style code in Tables 3 & 4. 6, 7 3/28/97 EIA-198-3-4-F Consolidated slash sheets 4 and 5 into one document. All 3/26/08 EIA-198-3-4-F Reformatted all tables to include all styles and TCC options. Various 3/26/08 EIA-198-3-4-F Renamed and revised section 2 to reflect supplier choice in defini

39、ng part numbers. 3 3/26/08 EIA-198-3-4-F Replaced Style codes with Size Identifiers in all references. Various 3/26/08 EIA-198-3-4-F Changed Size Identifier codes from 4 to 2 digit codes, reflecting identification of major manufacturers. Various 3/26/08 EIA-198-3-4-F Added dimensions for Molded Radi

40、al Size Identifiers -07 and -08 supported by multiple major manufacturers. Various 3/26/08 EIA-198-3-4-F Interchanged lead length/crimp length dimensions in Figure 2. 2 10/7/08 EIA-198-3-4-F Added B-tolerance description. Various 10/7/08 EIA-198-3-4-F Added J-tolerance for X7R in capacitance range c

41、harts. 5, 6 10/7/08 EIA-198-3-4-F Added requirements for solderability, vibration, resistance to solvents, moisture resistance, and thermal shock. 3 10/7/08 EIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, health or technical

42、reasons, please fill in the appropriate information below and mail or FAX to: Electronic Components Association Standards and Technology Department 2500 Wilson Blvd. Suite 310 Arlington, VA 22201 FAX: (703-875-8908) Document No.: Document Title: Submitters Name: Telephone No.: FAX No.: E-mail: Addre

43、ss: Urgency of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR EIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Electronic Components Association 2500 Wilson Boulevard, Suite 310 * Arlington, VA 22201 * tel 703-907-8021 * fax 703-875-8908 www.ecaus.org